Advertisement
Quick Links
Advertisement
Related Manuals for Hanwha Vision TNV-C8014RM
Summary of Contents for Hanwha Vision TNV-C8014RM
- Page 1 NETWORK CAMERA User Manual TNV-C8014RM TNV-C8034RM...
- Page 2 Network Camera User Manual Copyright ©2024 Co., Ltd. All rights reserved. Hanwha Vision Trademark Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Copyright of this document is reserved.
- Page 3 3. Heed all warnings. video. 4. Follow all instructions. 23. The operating temperature for the TNV-C8014RM/TNV-C8034RM products is -40°C to +55°C(-40°F to 5. Do not use this apparatus near water. +131°F). 6. Clean the contaminated area on the product surface with a soft, dry cloth or a damp cloth.
- Page 4 overview Class construction The ITE is to be connected only to PoE networks without routing to the outside plant. An apparatus with CLASS construction shall be connected to a MAINS socket outlet with a The wired LAN hub providing power over the Ethernet (PoE) in accordance with IEEE 802.3af shall be a UL Listed device with the output evaluated as a Limited Power protective earthing connection.
- Page 5 CONTENTS OVERVIEW WEB VIEWER Important Safety Instructions Connecting to the Camera Recommended PC Specifications Password setting Recommended Micro SD/SDHC/SDXC Login Memory Card Specifications Camera Web Viewer Setup NAS recommended specs APPENDIX Troubleshooting INSTALLATION & CONNECTION What’s Included At a Glance Installation Adjusting the monitoring direction for the camera...
- Page 6 overview RECOMMENDED PC SPECIFICATIONS NAS RECOMMENDED SPECS ~ CPU : Intel(R) Core(TM) i7 3.4 GHz or higher ~ Recommended capacity : 200GB or higher is recommended. ~ RAM : 8G or higher ~ For this camera, you are recommended to use a NAS with the following manufacturer’s specs. ~ Recommended browser: Chrome Recommended products : QNAP NAS, Synology NAS ~ Supported browsers: Chrome, Safari, Firefox, MS Edge(chromium based)
- Page 7 installation & connection WHAT’S INCLUDED AT A GLANCE As for each sales country, accessories are not the same. Audio I/O port Wiring hole cover Camera-body Dome-cover Microphone M12 Female hole connector IR LED Illumination Sensor Lens Use installation screws of at least M4, L30 for the installation of this product. Micro USB port Reset button...
- Page 8 installation & connection INSTALLATION Inserting a Micro SD card Insert the micro SD card into the micro SD card slot on the camera body in the arrow direction. Precautions before installation Ensure you read out the following instructions before installing the camera: ~ Select an installation site that can hold at least 5 times the camera’s weight.
- Page 9 Removing a Micro SD card Installation Gently press down on the exposed end of the Micro SD card as shown in the diagram to eject the Micro SD [Directly installing on wall/ceiling] card from the slot. 1. Place the camera body on the desired location considering the direction to be monitored, mark the locations for the screw holes, and then drill the holes.
- Page 10 installation & connection 3. Insert the external M12 male connector into the M12 female connector connection groove of the camera. Assembling the dome cover 4. Turn the screws on both sides of the camera lens fixing cover counterclockwise to loosen them. [Directly installing on wall/ceiling] Forcing to tilt the lens (hood) without loosening the screws may cause a product defect.
- Page 11 ADJUSTING THE MONITORING DIRECTION FOR THE CAMERA ` Methods of adjustment 1. Adjust the pan angle taking account of the direction to monitor. 2. Adjust the horizontal angle so that the video does not flip when rotated. 3. Adjust the tilt angle toward the direction to monitor. Tilt Tilt Lens Rotation...
- Page 12 installation & connection CONNECTING WITH OTHER DEVICE Connecting a connector cable Insert the external M12 male connector into the M12 female connector connection groove of the camera. WiFi dongle This camera uses Female, D-coded types. PoE (Power over Ethernet) is supported. You are recommended to use a shielded network connector.
- Page 13 Waterproofing of cable connections Connecting WiFi When you install the product outdoors without using the connectors and cables which meet the M12 Camera Setup specification, it should be waterproofed with waterproof butyl rubber tape (which can be purchased in stores) 1.
- Page 14 installation & connection Connecting to Audio Input/Output ~ Audio Codec - Audio In : G.711 PCM (Bit Rate: 64kbps / Sampling Frequency: 8kHz), G.726 ADPCM (Bit Rate: 16Kbps, 24Kbps, 32Kbps, 40Kbps / Sampling Frequency: 8kHz), AAC (Bit Rate: 48Kbps / Sampling Frequency: 16kHz) ~ Full duplex Audio Speaker...
- Page 15 network connection and setup CONNECTING THE CAMERA DIRECTLY TO A DHCP BASED DSL/CABLE You can set up the network settings according to your network configurations. MODEM CONNECTING THE CAMERA DIRECTLY TO LOCAL AREA NETWORKING Connecting to the camera from a local PC in the LAN INTERNET 1.
- Page 16 If using a Broadband Router ~ IP Address : Enter an address falling in the IP range provided by the Broadband Router. Device manager program can be downloaded from <Support>-<Online Tool> menu at Hanwha Vision website ex) 192.168.1.2~254, 192.168.0.2~254, (https://www.HanwhaVision.com).
- Page 17 AUTOMATICALLY CONFIGURING IP Configuring Dynamic IP Receive IP address from DHCP 1. Click the camera from the list that you want to automatically ~ Example of the Dynamic IP environment configure the IP. TNV-C8034RM - If a Broadband Router, with cameras connected, is assigned an IP address by the DHCP server 2.
- Page 18 network connection and setup PORT RANGE FORWARD (PORT MAPPING) SETUP Setting up Port Range Forward for several network cameras ~ You can set a rule of Port Forwarding on the Broadband Router device through its configuration web page. If you have installed a Broadband Router with a camera connected, you must set the port range forwarding on the ~ A user can change each port using the camera setting screen.
- Page 19 CONNECTING TO THE CAMERA FROM A SHARED LOCAL PC 1. Run device manager. It will scan for connected cameras and display them as a list. 2. Double-click a camera to access. The Internet browser starts and connects to the camera. Access to the camera can also be gained by typing the camera’s IP address in the address bar of the Internet browser.
- Page 20 web viewer web viewer CONNECTING TO THE CAMERA Connecting via Bonjour 1. Run the client or operating system in support of the Bonjour protocol. Normally, you would 2. Click the camera name for search. In the Mac operating system, click the camera name searched from the Bonjour tab of Safari. 1.
- Page 21 PASSWORD SETTING CAMERA WEB VIEWER SETUP When you access the product for the first time, you must register the 1. Click the [Setup ( )] icon. login password. 2. The Settings window appears. 3. You can configure settings for the camera’s basic information, video, audio, network, event, analysis, and For a new password with 8 to 9 characters, you must use at least 3 system over the network.
- Page 22 appendix TROUBLESHOOTING PROBLEM SOLUTION PROBLEM SOLUTION Voice is not recorded even though When an Windows 10 user accesses ~ You must enable the <Audio In> check box in <Basic> - <Video Profile>. ~ This is what happens when microphone driver has been set to Realtek driver. audio input settings are configured.
- Page 23 Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Hanwha Vision cares for the environment at all product manufacturing stages, and is taking measures to provide customers with more environmentally friendly products.
Need help?
Do you have a question about the TNV-C8014RM and is the answer not in the manual?
Questions and answers