Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Hanwha Vision TNO-7180R
Summary of Contents for Hanwha Vision TNO-7180R
- Page 1 NETWORK CAMERA User Manual TNO-7180R...
- Page 2 Network Camera User Manual Copyright ©2021 Co., Ltd. All rights reserved. Hanwha Vision Trademark Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Copyright of this document is reserved.
- Page 3 overview IMPORTANT SAFETY INSTRUCTIONS 21. Installing or using the product in water can cause serious damage to the product. 22. This device has been verified using STP cable. The use of appropriate GND grounding and STP cable 1. Read these instructions. is recommended to effectively protect your product and property from transient voltage, thunderstroke, 2.
- Page 4 For below models only. The ITE is to be connected only to PoE networks without routing to the outside plant. TNO-7180R The wired LAN hub providing power over the Ethernet (PoE) in accordance with IEEE 802.3bt shall be a UL Listed device with the output evaluated as a Limited Power Source as Risk Group 1 defined in UL60950-1 or PS2 as defined in UL62368-1.
- Page 5 CONTENTS OVERVIEW Important Safety Instructions WEB VIEWER Connecting to the Camera Recommended PC Specifications Password setting Recommended Micro SD/SDHC/SDXC Login Memory Card Specifications Camera Web Viewer Setup NAS recommended specs What’s Included At a Glance APPENDIX Troubleshooting INSTALLATION & CONNECTION Installation Connecting with other Device Powering and networking...
- Page 6 overview RECOMMENDED PC SPECIFICATIONS NAS RECOMMENDED SPECS ~ CPU : Intel(R) Core(TM) i7 3.4 GHz or higher ~ Recommended capacity : 200GB or higher is recommended. ~ RAM : 8G or higher ~ For this camera, you are recommended to use a NAS with the following manufacturer’s specs. ~ Supported OS : MS Windows 8.1, 10, Mac OS X 10.13 Recommended products : QNAP NAS, Synology NAS ~ Recommended browser: Google Chrome...
- Page 7 WHAT’S INCLUDED Please check if your camera and accessories are all included in the product package. (As for each sales country, accessories are not the same.) Appearance Item Name Quantity Description Appearance Item Name Quantity Description Used for dome cover Main Body disassembly, Screw bit...
- Page 8 overview AT A GLANCE Item Description Appearance Sunshield It protects the camera from the direct sunlight. IR LED These infrared LED’s are controlled by the illumination sensor. Lens Lens for the camera. Illumination Sensor Detects incoming light to control the IR LED. Installation base A part that is attached to the bracket or mounting surface for installation.
- Page 9 Inner View of Installation Base Screws used for installation For the screws that needs user adjustment during product installation, T30 should be used so that the screw driver bit shipped with the product can be used. Using screws other than T30 for adjustment might negatively impact the performance quality of the product (e.g.
- Page 10 installation & connection INSTALLATION Inserting a Micro SD card 1. With the provided screw driver bit, turn the screws counterclockwise to remove them from the Micro SD This camera is waterproof and in compliance with the IP66 spec, but the jack connected to the external cable is not. card cover.
- Page 11 Removing a Micro SD card Do not forcefully insert it in the reverse direction. It might damage your Micro SD card and your product. Gently press down on the exposed end of the Micro SD card as shown in the diagram to eject the Micro SD card from the slot.
- Page 12 overview Installing the installation base Installing the network cable 1. Use the screwdriver to connect the grounding 1. Remove the cable bushing from the installation base. wire to the GND on the bottom of the installation base. Grounding protects the product from a surge or lightning.
- Page 13 4. For waterproof protection, pull down the cable below the cable bushing as shown in the figure below. Installing audio/alarm/RS-485/power cables 1. Remove the cable bushing from the installation base. 5. Plug the network cable bushing into the installation base. 2.
- Page 14 installation & connection Installing the camera body 3. Use the provided driver bit to loosen the camera screws so that you can adjust the surveillance direction. You can adjust panning and tilting of your camera. 1. Connect the audio/alarm/RS-485/power/network cable to the installation base port. Tilt For power supply, connect the power cable to the provided terminal block and plug it in the port.
- Page 15 4. Once installation is complete, peel off the protective cover from the camera lens. English _15...
- Page 16 installation & connection CONNECTING WITH OTHER DEVICE Connecting WiFi Camera Setup 1. Connect OTG adapter (5-pin) and WiFi dongle to the micro USB port. Smartphone Setup WiFi dongle 1. Install the Wisenet Installation application. 2. Select the camera SSID after turning on the WiFi. RESET 3.
- Page 17 POWERING AND NETWORKING Network Cable Specification Item Contents Remark Connector RJ-45(10/100/1000BASE-T) To operate with 1000BASE-T, a cable of External internet Ethernet 10/100/1000BASE-T UTP-6 or higher should be used for the Giga hub. SFP Port Cable Category 6 Switch Switch Max Distance 100 m DC Resistance ≤...
- Page 18 installation & connection Connecting to Audio Input/Output Alarm input/output and RS-485 connection Microphone Speaker <ALARM IN/OUT> <RS-485> Network Microphone Alarm Sensor Speaker (Warning lamp) 1. Connect the MIC port of the camera with the microphone or LINE OUT port of the amplifier where the microphone is connected.
- Page 19 To connect the external sensor Connect one of the 2 signal lines to the [ALARM 1] port (if you want this to be the input port) and the remaining one to the [GND] port. Alarm In Wiring Diagram External Inside of the camera VCC_3.3V connection RESISTOR...
- Page 20 network connection and setup You can set up the network settings according to your network configurations. CONNECTING THE CAMERA DIRECTLY TO A DHCP BASED DSL/CABLE MODEM CONNECTING THE CAMERA DIRECTLY TO LOCAL AREA NETWORKING Connecting to the camera from a local PC in the LAN INTERNET 1.
- Page 21 If using a Broadband Router ~ IP Address : Enter an address falling in the IP range provided by the Broadband Router. Device manager program can be downloaded from <Support>-<Online Tool> menu at Hanwha Vision website ex) 192.168.1.2~254, 192.168.0.2~254, (https://www.HanwhaVision.com).
- Page 22 ~ Example of the Dynamic IP environment configure the IP. TNO-7180R - If a Broadband Router, with cameras connected, is assigned an IP address by the DHCP server 2. Click < + > at the main page of device manager.
- Page 23 PORT RANGE FORWARD (PORT MAPPING) SETUP Setting up Port Range Forward for several network cameras ~ You can set a rule of Port Forwarding on the Broadband Router device through its configuration web page. If you have installed a Broadband Router with a camera connected, you must set the port range forwarding on the ~ A user can change each port using the camera setting screen.
- Page 24 network connection and setup CONNECTING TO THE CAMERA FROM A SHARED LOCAL PC 1. Run device manager. It will scan for connected cameras and display them as a list. 2. Double-click a camera to access. The Internet browser starts and connects to the camera. Access to the camera can also be gained by typing the camera’s IP address in the address bar of the Internet browser.
- Page 25 web viewer CONNECTING TO THE CAMERA Connecting via Bonjour 1. Run the client or operating system in support of the Bonjour protocol. Normally, you would 2. Click the camera name for search. In the Mac operating system, click the camera name searched from the Bonjour tab of Safari. 1.
- Page 26 web viewer PASSWORD SETTING CAMERA WEB VIEWER SETUP When you access the product for the first time, you must register the 1. Click the [Setup ( )] icon. login password. 2. The Settings window appears. 3. You can configure settings for the camera’s basic information, video, audio, network, event, analysis, and For a new password with 8 to 9 digits, you must use at least 3 of system over the network.
- Page 27 appendix TROUBLESHOOTING PROBLEM SOLUTION PROBLEM SOLUTION ~ On the authentication popup window prompted when initially accessing https, click "View ~ Verify the settings in the following sequence: <Motion detection> of <Analytics> is Authentication Certificate" and select the "Always trust when connecting to the designated set to <Enable>, but no notification A.
- Page 28 Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Hanwha Vision cares for the environment at all product manufacturing stages, and is taking measures to provide customers with more environmentally friendly products.
Need help?
Do you have a question about the TNO-7180R and is the answer not in the manual?
Questions and answers