Page 3
overview IMPORTANT SAFETY INSTRUCTIONS 22. Although a rapid change in temperature could cause frost inside the dome, there will be no problem with the video. 23. This device has been verified using STP cable. The use of appropriate GND grounding and STP cable 1.
Page 4
For below model only. Do not arbitrarily loosen or tighten the gore valve. TNV-C7013RC The ITE is to be connected only to PoE networks without routing to the outside plant. Risk Group 1 (Groupe de Risque 1) The wired LAN hub providing power over the Ethernet (PoE) in accordance with IEEE 802.3af shall be a UL Listed device with the output evaluated as a Limited Power Source...
CONTENTS OVERVIEW Important Safety Instructions WEB VIEWER Connecting to the Camera Recommended PC Specifications Password setting Recommended Micro SD/SDHC/SDXC Login Memory Card Specifications Camera Web Viewer Setup NAS recommended specs What’s Included Optional Accessories for Installation At a Glance APPENDIX Troubleshooting INSTALLATION &...
overview RECOMMENDED PC SPECIFICATIONS NAS RECOMMENDED SPECS ~ CPU : Intel(R) Core(TM) i7 3.4 GHz or higher ~ Recommended capacity : 200GB or higher is recommended. ~ RAM : 8G or higher ~ For this camera, you are recommended to use a NAS with the following manufacturer’s specs. ~ Recommended browser: Chrome Recommended products : QNAP NAS, Synology NAS ~ Supported browsers: Chrome, Safari, Firefox, MS Edge(chromium based)
WHAT’S INCLUDED Appearance Item Name Quantity Description Please check if your camera and accessories are all included in the product package. (As for each sales country, accessories are not the same.) Cable bushing for network/power cable installation. Appearance Item Name Quantity Description Cable bushing...
overview OPTIONAL ACCESSORIES FOR INSTALLATION AT A GLANCE You can purchase appropriate optional accessories available. Appearance Dome cover SPG-VAN13W Item Description Dome cover Case cover used to protect the lens and the main unit. Camera body Body part where the camera lens and connection terminals are included. Mount Bracket Used to install the camera in a corner.
Page 9
Components (Camera body) Item Description Micro SD card slot Compartment for the Micro SD card. The button restores all camera settings to the factory default. Press and hold for about 5 seconds to reboot the system. If you reset the camera, the network settings will be adjusted so that DHCP can be Reset Button enabled.
installation & connection INSTALLATION 2. Remove the camera body by turning its fastening screw counterclockwise. You don’t have to completely remove the screws. This camera is waterproof and in compliance with the IP66 spec, but the jack connected to the external cable is not. You are recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.
Page 11
Inserting a Micro SD card Removing a Micro SD card Slide the Micro SD card into the Micro SD card slot on the camera module in the direction of the arrow. Gently press down on the exposed end of the Micro SD card as shown in the diagram to eject the Micro SD card from the slot.
Page 12
installation & connection Installation (mount bracket) 1-3. Pull out network cable through the hole in the mount bracket. [Direct installation] 1-1. Punch a hole for cable passage within the designated area. 90 mm 65 mm [Installing using pipe] Install the dome cover (SPG-VAN13W) after separately purchasing it to connect and install a pipe. 2-1.
Page 13
2-3. Pull out network cable through the pipe. [Installing the network cable] (IP66) 2-1. Pull off the extruded part of the 1-hole cable bushing provided. 2-2. Use the cap installer to pass through the network cable. 2-3. Mount the cable bushing to the camera body. Installation (camera body) 1.
Page 14
installation & connection 2-4. Connect the network cable jack to the PoE port of the camera body. 3-4. Mount the cable bushing to the camera body. [Installing audio/alarm cables] 4. Pull out the cable bushings from the camera body. [Installing network/power cables] 3-1.
Page 15
5. Insert the cable bushing of the audio/alarm cables into the camera body. 7. Using the fastening screws on the camera body, fix the camera body to the mount bracket. 6. Connect the audio/alarm cable connector to the audio/alarm cable port of the camera body. TR20 English _15...
Page 16
installation & connection Installation (dome cover) [Installing using pipe] 9-1. Assemble the dome cover. [Direct installation] Install the dome cover (SPG-VAN13W) after separately purchasing it. 8-1. Assemble the dome cover. Make sure to firmly tighten the fastening screws so that there is no water damage issue. Make sure to firmly tighten the fastening screws so that there is no water damage issue.
Page 17
9-2. Cover the unused pipe hole with a cap. Outdoor installation When you install it outside of the building, please waterproof it with waterproof butyl rubber tape (can be purchased in stores) so that water does not leak from the gap of the cable connected to the outside. 1.
installation & connection Setting focus CONNECTING WITH OTHER DEVICE Adjust the focus for a clearer image by turning the lens. Adjust the focus after removing the lens protection cover. Power Power Ethernet Ethernet Ethernet Connection Connect the Ethernet cable to the local network or to the Internet. 18_ installation &...
Page 19
Power Supply Use the screwdriver to connect each line (+, –) of the power cable to the corresponding power port of the Connecting audio and alarm I/O camera. If the power source for PoE and DC 12V are simultaneously turned on, the device power will be supplied by DC 12V. Speaker You can also use a router featuring PoE to supply power to the camera.
Page 20
installation & connection Connecting to the I/O port box To connect to an external sensor Connect the Alarm I/O cable to the corresponding port of the port box. To use as an Alarm IN: Connect one of the [ALARM I/O] port and the other terminal to the [GND] port. Alarm In Wiring Diagram(example) Alarm cable External connection...
network connection and setup CONNECTING THE CAMERA DIRECTLY TO A DHCP BASED DSL/CABLE You can set up the network settings according to your network configurations. MODEM CONNECTING THE CAMERA DIRECTLY TO LOCAL AREA NETWORKING Connecting to the camera from a local PC in the LAN INTERNET DSL/Cable Modem 1.
If using a Broadband Router ~ IP Address : Enter an address falling in the IP range provided by the Broadband Router. Device manager program can be downloaded from <Support>-<Online Tool> menu at Hanwha Vision website ex) 192.168.1.2~254, 192.168.0.2~254, (https://www.HanwhaVision.com).
~ Example of the Dynamic IP environment configure the IP. TNV-C7013RC - If a Broadband Router, with cameras connected, is assigned an IP address by the DHCP server 2. Click < + > at the main page of device manager.
network connection and setup PORT RANGE FORWARD (PORT MAPPING) SETUP Setting up Port Range Forward for several network cameras ~ You can set a rule of Port Forwarding on the Broadband Router device through its configuration web page. If you have installed a Broadband Router with a camera connected, you must set the port range forwarding on the ~ A user can change each port using the camera setting screen.
CONNECTING TO THE CAMERA FROM A SHARED LOCAL PC 1. Run device manager. It will scan for connected cameras and display them as a list. 2. Double-click a camera to access. The Internet browser starts and connects to the camera. Access to the camera can also be gained by typing the camera’s IP address in the address bar of the Internet browser.
web viewer CONNECTING TO THE CAMERA Connecting via Bonjour 1. Run the client or operating system in support of the Bonjour protocol. Normally, you would 2. Click the camera name for search. In the Mac operating system, click the camera name searched from the Bonjour tab of Safari. 1.
PASSWORD SETTING CAMERA WEB VIEWER SETUP When you access the product for the first time, you must register the 1. Click the [Setup ( )] icon. login password. 2. The Settings window appears. 3. You can configure settings for the camera’s basic information, video, audio, network, event, analysis, and For a new password with 8 to 9 digits, you must use at least 3 of system over the network.
appendix TROUBLESHOOTING PROBLEM SOLUTION PROBLEM SOLUTION ~ Verify the settings in the following sequence: When an Windows 10 user accesses <Motion detection> of <Analytics> is ~ This is what happens when microphone driver has been set to Realtek driver. the web viewer through Chrome set to <Enable>, but no notification A.
Page 29
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Hanwha Vision cares for the environment at all product manufacturing stages, and is taking measures to provide customers with more environmentally friendly products.
Need help?
Do you have a question about the TNV-C7013RC and is the answer not in the manual?
Questions and answers