Download Print this page

Advertisement

Quick Links

UV 3040
SERIES MANUAL
WE VALUE YOUR TRUST
Thank you for purchasing our company's products.
Here are the specific instructions for using the equipment.

Advertisement

loading
Need help?

Need help?

Do you have a question about the UV 3040 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for DoCash UV 3040

  • Page 1 UV 3040 SERIES MANUAL WE VALUE YOUR TRUST Thank you for purchasing our company's products. Here are the specific instructions for using the equipment.
  • Page 2 1.Please Note 17.Please ensure that the machine is properly grounded. Please read this instruction carefully before using UV 3040: 18.Please avoid using this machine during thunderstorms to avoid lightning 1.This machine cannot be used by children or disabled people, please use it under strikes.
  • Page 3 Confirm that the boot operation is normal 3. Preparation before use Please ensuring that the machine is placed appropriately, removingthe machine's fixed sheet 1.Confirm that the machine has a normal appearance and is placed stably. Check whether the power supply voltage mark of the machine is 220V or 110V. It should only be used if it metal, and confirming that the power-on andstartup actions are normal and the machine matches the local supply voltage.
  • Page 4 2.The computer must be equipped with a Gigabit LAN card and a Gigabit network cable so that the software can be connected normally. 3.Set the computer IPv4 address to 192.168.127.11, and do not check IPv6. Only then can the driver automatically connect normally. Add in The operation is as follows: Find the icon in the lower right corner of the desktop, right-click, select [Open Network and...
  • Page 5 5.Open the decompressed software, find it RIIN and double-click to open it. 6.Check if the software recognizes the encryption port, if it shows UV-A3 version, it is normal. 7.Open the system se ngs and find the control so ware. When the green hinge icon is displayed in the lower le corner, it means that the driver is online.
  • Page 6 10 . Control software setup instructions There are three options: printing to the left,printing to the right, Printing direction and bidirectional printing. The control software display interface is mainly divided into three parts: You can choose to turn off feathering, light feathering, normal feathering, 1.
  • Page 7 Calibration process: <2> Vertical Check:lf the print head is vertically offset to the left or right, you need to loosen the head fixing screw and gently twist it left or right to adjust. When a new machine is installed, replaced or hits the print head, calibrate it from top to bottom to complete the calibration work.
  • Page 8 Click left to calibrate, and the machine will print a calibration chart. Voltage: The correct result is that the coincidence position of the calibration line and the reference line is at position 0. Otherwise, please add or subtract the value of the coincidence position of the calibration line and the reference line on the original basis and enter it in the corresponding color box.
  • Page 10 <3> Ruler: <2> Data source: Select the ink output method corresponding to the spot color. Take white ink printing as an In order to show the actual size and position of the canvas and image, RIIN RIP software example (the varnish is the same to introduce the functions. sets rulers (including horizontal rulers and vertical rulers).
  • Page 11 <7> Adjustment range: <3> When the machine is not in use, please turn it on once a day and print test strips. If the ink of the test strip is broken, automatic cleaning is required to ensure that the -5 to +5. test strip is normal.
  • Page 12 Solution: Description: This status indicates that the machine's nozzle is in good condition. 1. Use automatically clean and check whether it can absorb ink from damper. If not, please replace it with a new cap or readjust its position. <2> The ink of the test strip is partially broken 2.C heck whether there is any ink residue on the surface of the head.
  • Page 13 Solution: 1.C heck whether the height of the nozzle and the print media are within 2-3mm. Solution: 2.T he printing environment temperature is within the range of 25℃~30℃. 1.U nplug and plug the head wire, check whether it contacts are oxidized or damaged, if so, 3.T est whether the ink-absorbing pad can draw ink normally.