Download Print this page
Lumag RAMBO-V2 Original Operating Instructions
Lumag RAMBO-V2 Original Operating Instructions

Lumag RAMBO-V2 Original Operating Instructions

Petrol chipper

Advertisement

Quick Links

Translated from German to English - www.onlinedoctranslator.com
PETROL CHIPPER
original operating instructions
RAMBO‐V2
ATTENTION! The machine is delivered without engine oil and without fuel.
Both the model number and the serial number can be found on the nameplate on the machine.
You should keep both numbers safe so that you can access them in the future. This
Instructions explain the functions and applications of the machine.
FOR YOUR SAFETY
Before using the device, read the operating instructions,
Safety and warning instructions must be observed!

Advertisement

loading
Need help?

Need help?

Do you have a question about the RAMBO-V2 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Lumag RAMBO-V2

  • Page 1 Translated from German to English - www.onlinedoctranslator.com PETROL CHIPPER original operating instructions RAMBO‐V2 ATTENTION! The machine is delivered without engine oil and without fuel. Both the model number and the serial number can be found on the nameplate on the machine. You should keep both numbers safe so that you can access them in the future.
  • Page 2 9.1.1 Electric start 9.1.2 Safety circuit (EMERGENCY STOP) 21. Warranty/Guarantee/Customer Service 10. Technical Description 22. EC Declaration of Conformity 11. Scope of delivery 23. Components RAMBO-V2 12th assembly 24. Notes 13. Drive type 13.1 Gasoline engine 13.2 Refueling 13.2.1 Filling engine oil 13.2.2 Refueling...
  • Page 3 1.1 Information on the operating instructions 1.4 Copyright This operating manual provides important information on handling the RAMBO-V2 petrol chipper. The All documents are protected by copyright. The prerequisite for safe working is correct compliance with distribution and reproduction of documents,...
  • Page 4 2. Intended use 3. Operating hours restriction The petrol shredder – RAMBO-V2 – is designed In residential and small settlement areas or on exclusively for shredding bushes, shrubs, bark the premises of hospitals and care facilities, and branches up to 15 cm thick. The machine is shredders may not be operated all day on not suitable for processing garden soil.
  • Page 5 5. Security 5.2 Safety instructions This section provides a comprehensive WARNING! overview of all important safety aspects for adequate protection of the operator as well as Familiarize yourself with the machine. for safe and trouble-free operation. Proper training is a prerequisite for working safely with this machine.
  • Page 6 and endanger other persons through improper Operation use. First-time users should seek instruction from WARNING! the seller to familiarize themselves with the The shredded material is ejected from the characteristics of the machine, its intended use machine at high speed. Always wear and the necessary safety devices.
  • Page 7 If handled improperly, the sharp edges of end of work the knives can pose a significant risk of Do not leave the machine unattended while injury.Make sure that the two chopping blades the engine is running. and the counter blade are correctly installed and securely fastened.
  • Page 8 5.4 Transport must not be put into operation with such damage. When transporting the machine on a vehicle or Close the tank cap properly after refueling. trailer and before moving it to another location, switch off the engine and wait until the work tools have come to a standstill.
  • Page 9 Work on the electrical system may only be carried out by qualified electricians. personal protective equipment (PPE) Only use original LUMAG spare parts and negligent use omission accessories. The use of other spare parts and personal protective equipment can result in accessories increases the risk of accidents.
  • Page 10 danger from noise 6. Warning and information hearing loss symbols used Prolonged, unprotected work with the machine can lead to hearing damage. → Always wear hearing protection. Symbols are provided on the machine to provide important information about the Hazards from materials and other substances product and instructions for use.
  • Page 11 with Carry you safety shoes Keep bystanders away from the work steel caps. area. chopping of branches of all kinds Wear protective gloves. up to max. 150 mm diameter, depending on the type and freshness of the wood. Wear eye protection. electric start, ignition key (12V) Wear hearing protection.
  • Page 12 7. Part designation 7.1 Shredder 7.2 gasoline engine trailer hitch safety chain drawbar Front axle, foldable with wheel brake Adjustable discharge flap fuel tap discharge chute, two-part (between tank and engine) gasoline engine rubber protective flap safety bar (EMERGENCY STOP) 10 Feed hopper, foldable 11 Transport wheel (2x) 12 drum chippers...
  • Page 13 8. Functions oil drain plug The oil drain plugs are located on the sides of the engine. 8.1 Engine fuel tank The fuel tap is located under the tank. Engine switch (main switch) = ignition switch on the electric starter (1) The engine switch in the OFF position prevents the machine (engine) from starting.
  • Page 14 9. Technical data IMPORTANT NOTE! model number RAMBO-V2 When loading, remove the drawbar or fold it drive up and secure it with a cotter pin! V-twin engine 4-stroke OHV Beninmotor 999 cm³ displacement Engine power, max. 24.5 kW* CAUTION! 3,600 rpm Engine speed max.
  • Page 15 10. Technical Description Connecting the battery: 1. Turn the ignition key on the electric starter to the OFF position and remove it. 2. First connect the red cable to the positive The shredder is used to chop woody material, pole (+). preferably in the garden area.
  • Page 16 If you have any questions or problems during installation, please contact us. You can reach us by email: info@lumag-maschinen.de or by phone at +49 8571/92 556-0. To simplify the assembly process, we have divided the assembly instructions into several steps.
  • Page 17 CAUTION! Step 3: Install rear tire (D2) The frame with rotor and petrol engine is very heavy (approx. 200 kg). Please pay attention The rear tires are mounted on the rear axle. on the weight! Lift the assembly using a forklift or crane rear axle remove.
  • Page 18 Now place the front axle carrier in the already mounted retaining plate. Now screw the front axle carrier to the retaining plate using the 4 hexagon screws, washers and nuts (Image 3+4). release the parking brake Figure 3 Figure 4 Step 5: Mount the front axle (F) parking brake locked The front axle is mounted on the front axle...
  • Page 19 Step 7: Install tank brackets (I) mounts on the rotor frame. Then slide it on. The tank brackets are mounted on the engine. Now close the feed hopper and secure it with the two clamps. Finally, it must be secured against accidental opening with the two Mount the two tank brackets using the hexagon screws!
  • Page 20 Figure 1 (C1) Figure 2 (C2) Step 12: Drawbar with trailer coupling + Install chain (K) The drawbar is mounted on the front axle carrier. The pull rod is inserted and screwed in using a hexagon screw, washer and nut as shown in Figure 1.
  • Page 21 13. Drive type Check engine oil level 13.1 Gasoline engine Turn off the engine and let it cool down. The machine is powered by a petrol engine. For information on starting and stopping the 1. Remove the dipstick. petrol engine, please refer to the engine 2.
  • Page 22 13.2.2 Refueling refueling 1. Turn the fuel tap to OFF. 2. Clean the area around the fuel tank cap of dirt and foreign objects. DANGER! 3. Unscrew the tank cap. 4. Fuel tank withgasoline (RON95)To allow health risk of explosion through room for the gasoline to expand, do not fill Combustion engine.
  • Page 23 14. Commissioning When shredding, shredded material, stones, etc. can be sprayed away. No other people or animals may be in the ejection area = danger zone. The machine must not be set up on a sloping surface. Particular care must be Also pay attention to vehicles, windows and taken to ensure that the floor does not other objects so that they are not damaged.
  • Page 24 5. If the choke lever was set to START (=CHOKE) to start the engine, gradually return it to DANGER! RUN (=RUN) while the engine warms up. Do not start the engine in enclosed spaces. The exhaust fumes contain carbon monoxide, which is very toxic if inhaled! To operate, open the throttle fully and slowly move it towards HIGH/FAST (=RABBIT).
  • Page 25 14.4 Stopping the engine in an emergency In dangerous situations, machine movements must be stopped as quickly as possible and the power supply switched off. In case of danger: 1. Press the safety bar on the feed hopper; an EMERGENCY STOP is initiated. 2.
  • Page 26 15. Chipping operation For constipation: Before each use, check the machine for: – loose screws and nuts – damaged rubber flap in the feed hopper, replace if necessary Switch off the engine and remove the spark plug – Function of the safety circuit connector for safety reasons! –...
  • Page 27 15.2 Chopping – Process shredded material with a high water content alternately with woody material to avoid clogging the machine. Make sure the shredded material is as DRY – The blade system draws in the chopped as possible! Shredded material that is too material largely independently.
  • Page 28 – Non-slip safety shoes – Safety glasses with side protection when working on pressurized components or near pressurized systems Only use original LUMAG spare parts. Other parts can cause unforeseeable damage and injuries. Work on the electrical equipment may only be carried out by qualified electricians.
  • Page 29 16.2 Maintenance plan The following sections describe the maintenance work required to ensure optimal and trouble-free operation. After After After Every Before 25 Bh* 30-50 season everyone everyone respectively Requirement maintenance work Bra* Bra* first 1 bra* 5 Bh* Check the machine ■...
  • Page 30 16.3 Lubricants IMPORTANT NOTE! Fuels and lubricants used must comply with the operator's operating fluids regulations and the specified specifications; if necessary, consult the supplier. fuel module specification filling quantity fuel Motor 10.0 liters gasoline ROZ95 or higher 10W-30 or Motor 2.4 liters engine oil...
  • Page 31 5. Screw the oil drain plug and new oil filter back in. Lightly coat the oil filter seal with oil. 6. Slowly pour 2.4 liters of engine oil into the oil filler cap 7. Screw the oil filler cap tightly 8.
  • Page 32 16.5.1 Check drive belt for wear and 16.6 Changing/cleaning the air filter tension To check the drive belts: DANGER! 1. Remove the belt cover 2. If the drive belts show wear, both must be Risk of fire and explosion when handling replaced flammable liquids! See…...
  • Page 33 16.7 Check/change/clean spark plug 16.9 Check wheels and tire pressure Wheels (tread and tire condition) and tire pressure: – Check that the screw connection on the wheel DANGER! axles is correctly seated. Danger of burns! – Check for cuts and foreign objects in the tire tread The engine and parts (e.g.
  • Page 34 Check and, if necessary, repair loose – Dispose of cleaning cloths and processing residues connections properly. in an environmentally friendly manner in compliance with applicable local regulations – use a soft brush or a vacuum cleaner for Interval: weekly interior cleaning After cleaning, check that all previously opened covers and safety devices have been properly 16.13 Check and repair construction...
  • Page 35 17th transport 17.1 Transport by hand Grab the machine by the drawbar, lift it slightly and move it. DANGER! 17.2 Transport with chassis Danger of burns from hot surfaces on the engine! 1. Attach the trailer hitch to the towing vehicle.
  • Page 36 18. Storage 19. Disposal Storage of the machine and temporary When the machine is no longer serviceable and decommissioning. is to be scrapped, it must be deactivated and dismantled, that is, it must be brought to a condition where it can no longer be used for Store the machine under the following conditions: the purposes for which it was designed.
  • Page 37 20. Troubleshooting WARNING! Any faults in the machine or engine that require major intervention should always be repaired by your LUMAG specialist workshop or an authorized specialist workshop. Improper intervention will void the warranty. Before any troubleshooting – Switch off the machine, remove the ignition key –...
  • Page 38 The guarantee for LUMAG products is 24 months for exclusively private use, and 12 months for commercial or Service time: Monday to Thursday from 7.30 a.m.
  • Page 39 22. CE declaration of conformity In accordance with the provisions of the EC directives Machinery Directive 2006/42/EC EMC Directive 2014/30/EU explains the company LUMAG GmbH Rudolf-Diesel-Straße 1a D-84375 Kirchdorf a.Inn Phone: +49 8571 / 92 556-0 Fax: +49 8571 / 92 556-19...
  • Page 40 23. Components RAMBO‐V2 WARNING! All repairs to the machine must be carried out by authorized personnel. Any necessary electrical work should only be carried out by an authorized specialist.
  • Page 41 24. Notes...
  • Page 44 Subject to change! Version RAMBOV2 (06.2024 D) LUMAG specialist dealer can be found at: www.lumag-maschinen.de LUMAG GmbH Rudolf-Diesel-Str. 1a D-84375 Kirchdorf a.Inn Germany Internet:www.lumag-maschinen.de...