Related Manuals for Lumag Rambo HC15
Summary of Contents for Lumag Rambo HC15
- Page 1 Distribution Limited Petrol Wood Chipper Operator’s Manual HC15 FOR YOUR SAFETY READ AND UNDERSTAND THE ENTIRE MANUAL BEFORE OPERATING THIS MACHINE...
- Page 3 For the warranty to be valid the Warranty Registration Form must be completed and returned to Lumag Distribution Limited within 14 days of the purchase, together with a copy of the purchase invoice. We will use your email to confirm that we have received the completed Warranty Registration Form and contact you about any errors or omissions on the form.
- Page 5 All Other Moving Parts & Lubricate X (2) Cables 1 – First service only, 2 = Should be carried out by your Lumag Dealer, 3 = May need to be done more often in dusty areas & 4 = Replace paper element only...
-
Page 9: Table Of Contents
Table of Contents Table of Contents PART I: General Safety Rules ......................2 PART II: Familiar with the Wood Chipper ..................7 PART III: Operating the Wood Chipper .................... 8 PART IV: Maintaining the Wood Chipper..................10 PART V: Troubleshooting and Parts List ..................12 Conventions used in this manual WARNING This indicates a hazardous situation, which, if not avoided, could result in death or serious... -
Page 10: Part I: General Safety Rules
Part I: General Safety Rules PART I: General Safety Rules Safety Labels Found on Your Unit... - Page 11 Part I: General Safety Rules WARNING Read this Safety & Operating Instructions manual before you use the Wood Chipper. Become familiar with the operation and service recommendations to ensure the best performance of your machine. Propose CAUTION This machine is designed solely to chip wood and must not be used for any other purpose. It should only be used by trained operators who are familiar with the content of this manual.
- Page 12 Part I: General Safety Rules WARNING This is a high-powered machine, with moving parts operating with high energy. You must operate the machine safely. Unsafe operation can create a number of hazards for you, as well as anyone else in the nearby area. Always take the following precautions when using this machine: A.
- Page 13 Part I: General Safety Rules completely. Don't handle gasoline if you or anyone nearby is smoking, or if you're near anything that could cause it to ignite or explode. Reinstall the fuel tank cap and fuel container cap securely. If you spill gasoline, do not attempt to start the engine. Move the machine away from the area of the spill and avoid creating any source of ignition until the gas vapors have dissipated.
- Page 14 Part I: General Safety Rules disconnect the spark plug wire, keeping it away from the spark plug to prevent accidental starting, wait 5 minutes for engine to cool down, then inspect for damage. Vibration is generally a warning of trouble. Check damaged parts and clean, repair and/or replace as necessary.
-
Page 15: Part Ii: Familiar With The Wood Chipper
Part II: Familiar with the Wood Chipper PART II: Familiar with the Wood Chipper It may be helpful to familiarize yourself with the controls and features of the Wood Chipper. If you have any question, please contact the dealers in your area. TECHNICAL SPECIFICATIONS Recoil Start Engine... -
Page 16: Part Iii: Operating The Wood Chipper
Part III: Operating the Wood Chipper PART III: Operating the Wood Chipper It may be helpful to better familiarize yourself with the features of your Wood Chipper before beginning the steps outlined in this chapter. WARNING A. Read and understand all instructions, safety precautions, and/or warnings listed in “PART I: General Safety Rules”... - Page 17 Part III: Operating the Wood Chipper Stopping Move the Throttle Lever to IDLE. Recoil Start: Turn the Ignition Switch to the OFF position. Electric Start: Turn the Key to the OFF position. Operator Zone Wood Chipping NOTICE Woods’ and branches’ diameter should be no bigger than 120mm. WARNING Do not place your hands into the chute when loading.
-
Page 18: Part Iv: Maintaining The Wood Chipper
Part IV: Maintaining The Wood Chipper PART IV: Maintaining the Wood Chipper Regular maintenance is the way to ensure the best performance and long life of your machine. Please refer to this manual and the engine manufacturer's user manual for maintenance procedures. - Page 19 Part IV: Maintaining The Wood Chipper Lubrication NOTICE All Bearings of your Chipper are sealed units and should have sufficient lubricant to last the life of your machine with normal use. Greasing the rack and Pinion NOTICE All the rack and pinion should be greased before every use.
-
Page 20: Part V: Troubleshooting And Parts List
Part VI: Troubleshooting and Parts List PART V: Troubleshooting and Parts List Most problems are easy to fix. Consult the Troubleshooting Table below for common problems and their solutions. If you continue to experience problems, contact the dealers in your area. WARNING Before performing any maintenance procedure or inspection, stop the engine, wait five minutes to allow all parts to cool. - Page 21 Part VI: Troubleshooting and Parts List Rack catching on tail Adjust carriage hold downs (slide guides). tube (at end of stroke). Check for wood chips or debris between ram bushing plate and beam. Rack returning very slow Check rack lift bearing for alignment or damage.
- Page 22 Distribution Limited PART DRAWINGS FOR YOUR SAFETY READ AND UNDERSTAND THE ENTIRE MANUAL BEFORE OPERATING THIS MACHINE...
- Page 23 Part VI: Troubleshooting and Parts List Explosion View Ref.No. Description Ref.No. Description foundation Feet fixation Wheel axis tower Blade Tower hitch wheel Discharge chute Belt cover inner plate Chute adjust clutch Engine fixation bearing In-feed pulley Belt 42*9*5 spacer Rubber plate Belt cover Rubber fixation(upper) Bearing fixation frame...
- Page 24 Unit 10, Hatchmoor Industrial Estate, Hatherleigh, Okehampton, Devon EX20 3LP www.lumag-gb.co.uk 01837 811741 Lumag Distribution Limited Company Number: 09267547 VAT Number: GB154566788 Hatherleigh Plant and Tool Hire is a trading name of Lumag Distribution LTD...
Need help?
Do you have a question about the Rambo HC15 and is the answer not in the manual?
Questions and answers