Advertisement
Quick Links
Advertisement
Related Manuals for CTC Union FRM220-10G-SXX
Summary of Contents for CTC Union FRM220-10G-SXX
- Page 1 FRM220-10G-SXX (H/W ver.2.1) 10G 3R Transponder...
- Page 2 8F, No. 60 Zhouzi St., Neihu, Taipei 114, Taiwan T +886-2-26591021 F +886-2-26590237 E sales@ctcu.com H www.ctcu.com 2019 CTC Union Technologies Co., LTD. All trademarks are the property of their respective owners. Technical information in this document is subject to change without notice.
- Page 3 Table of Contents Introduction ................... 4 Specifications ................5 Management Features ..............6 Panel ....................6 LED Indicators ................7 Installation ..................7 Operation Modes ................8 Auto Laser Shutdown ..............8 Console Management ..............9 Main Menu Operation ..............10 Loop Back Testing (LBT) ............
- Page 4 Introduction FRM220-10G-SXX is a 3-port 3R optical regeneration device with clock data recovery (CDR). The "3R" consists of Re-amplification, Re-shaping and Re-timing. The transponder card converts a data signal to the correct wavelength for transmission on a specific channel by supporting XFP, and/or SFP+ optics on both line side and client side interfaces.
- Page 5 Specifications Optical Interface Connector 2-XFP and 1-SFP+ cage Data rate 1Gbps ~ 10Gb/s (selectable fixed rates) Duplex mode Full duplex Fiber Depends on XFP/SFP+ Distance Depends on XFP/SFP+ Wavelength Depends on XFP/SFP+ Voltage 3.3V for SFP+ / 5V, -5.2V, 3.3V, 1.8V for XFP Clock SFP+ requires no reference clock XFP with or without reference clock...
- Page 6 2. Rack management - When placed in NMC managed rack, all other settings are overridden by the NMC management. 3. Due to their power requirements and high heat dissipation, CTC Union recommends placing no more than 10 cards in CH20 rack with empty space between each card.
- Page 7 CH-02M, CH02-NMC or the CH-20 chassis. CH02M Chassis AC, DC, 2AC, 2DC, or AD CH02-NMC Chassis AC, DC, 2AC, 2DC, or AD FRM220-CH20 Figure 2. Slide-in Card mounting of FRM220-10G-SXX Follow all ESD precautions when handling the card and XFP/SFP+ modules.
- Page 8 Operation Modes FRM220-10G-SXX is constructed with three ports and is programmable to send bi-direction data between any two ports as follows: Manual Primary – data is routed between the line side SFP+ and the primary XFP. Use this mode for SFP+ to XFP conversion.
- Page 9 Connect the serial cable to CH02M's DB9. Run the terminal emulation program. About 15 seconds after being powered on, the 10G-SXX will display the main menu as shown in the following example. **************************************** CTC UNION TECHNOLOGIES CO.,LTD FRM220-10G Manager Ver:1.01 **************************************** Model:[FRM220-10G-SXX] Ver:[2.100-2.030-0.000-1.624]...
- Page 10 Main Menu Operation Select any of the menu items by keying in the menu item number or letter. Use the [ESC] to return to a previous menu. Any setting is immediately applied to the transponder's circuitry. After all of the parameter settings have been selected, press "s"...
- Page 11 Operating Mode: Fiber Detect Mode: <0> Auto <1> SM Auto <2> Manual Pri <3> Manual Sec <4> Manual Pri to Sec <ESC> Go to previous menu. Please select an item. These operating modes are selected when the converter is being used as a 1+1 protection on XFP.
- Page 12 Loop Back Testing (LBT) The loop back capability of FRM220-10G-SXX is useful for debugging a dysfunctional link, or when commissioning a site. In loopback mode, the signal is routed into the CDR (Clock Data Recovery) circuitry and then routed back to the signal source. FRM220-10G-SXX model features loop back for each of the three fiber ports, Line, Primary and Secondary.
- Page 13 The rate setting is the only setting required. For normal operation, ensure that no Loop Back is configured. Since FRM220-10G-SXX 3R transponder has a clock recovery function, it is able to repeat indefinitely and still maintain data integrity.
- Page 14 CWDM Transponder FRM220-10G-SXX functions primarily as a repeater or a media converter. As a repeater for long-haul applications, the signal is fully regenerated at the trunk. Clock Data Recovery (CDR) helps in reshaping, retiming, and regenerating (3R) the output signal at a number of pre-assigned frequencies for different protocols.
- Page 15 (DOM) and gives the end user the ability to monitor real-time parameters of the SFP, such as optical output power, optical input power, temperature, etc. Example of reading Digital Diagnostics in XFP **************************************** CTC UNION TECHNOLOGIES CO.,LTD FRM220-10G Manager Ver:1.01 **************************************** XFP/SFP+ Digital Diagnostic <1>...
- Page 16 Upgrading The FRM220-10G-SXX card may be firmware upgraded when it is placed in the FRM220 with NMC management card. The user may use a local console connection to the NMC, a remote Telnet (IP) connection, or a Web based (HTTP) connection with any available browser. The NMC communicates to all cards through a serial TTL control bus.
- Page 17 About XFP/SFP+ Units The FRM220-10G-SXX accepts any XFP or SFP+ unit that complies with the MSA standard. It will also accept “multiple voltage” XFPs and should not be a problem for any new XFP. Follow all ESD precautions when handling the card and pluggable modules.
Need help?
Do you have a question about the FRM220-10G-SXX and is the answer not in the manual?
Questions and answers