Parker PVSG-IoT-TP 4GLTE Series User Manual

Vehicle system gateway for mobile iot

Hide thumbs

page of 29

/ 29
Bookmarks

Quick Links

Download this manual

Parker Vehicle System Gateway for Mobile IoT

PVSG-IoT-TP*-4GLTE

U s e r G u i d e

Need help?

Do you have a question about the PVSG-IoT-TP 4GLTE Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Parker PVSG-IoT-TP 4GLTE Series

Page 1 Parker Vehicle System Gateway for Mobile IoT PVSG-IoT-TP*-4GLTE U s e r G u i d e...
Page 2 Copyright 2023 © Parker Hannifin Corporation. All rights reserved. No part of this work may be reproduced, published, or distributed in any form or by any means (electronically, mechanically, photocopying, recording, or otherwise), or stored in a database retrieval system, without the prior written permission of Parker Hannifin Corporation in each instance.
Page 3 Table of Contents Safety symbols ..........................5 1. PVSG-IoT-TP*-4GLTE Service and Plan Offerings ................7 1.1 Plug & Play Hardware ......................7 1.2 Part Numbers & Accessories ....................8 1.2.1 Lite Service Plan Feature Content .................. 9 1.2.2 Standard Service Plan Feature Content ...............
Page 4 7. Need Further Assistance? ......................25 7.1 Where to find help? ......................25 7.2 IoT Community Page ......................25 7.3 Parker Mobile IoT Service App ..................25 8. Markings/Approvals ....................... 25 8.1 FCC Compliance ......................25 8.2 IC Compliance ......................... 26 9.
Page 5 Contact the manufacturer if there is anything you are not sure about or if you have any questions regarding the product and its handling or maintenance. The term "manufacturer" refers to Parker Hannifin Corporation. Safety symbols The following symbols are used in this document to indicate potentially hazardous situations: Danger! Risk of death or injury.
Page 6 Welding after installation Complete as much as possible of the welding work on the chassis before the installation of the system. If welding must be done afterward, proceed as follows: Do not place the welding unit cables near the electrical wires of the control system. Disconnect the electrical connections between the system and external equipment.
Page 7 1. PVSG-IoT-TP*-4GLTE Service and Plan Offerings 1.1 Plug & Play Hardware The main features of the PVSG-IoT-TP*-4GLTE hardware are listed in the following table: Connectivity 4G NA and 3G EU/AUS/NZL / eSIM included Environmental IP67 rating and hardened Certifications FCC, ISED RSS, CE, RCM, ICASA, POTRAZ RAM Memory 512 MB Flash Memory...
Page 8 1.2 Part Numbers & Accessories The PVSG-IoT-TP*-4GLTE can be activated with one of three available service plans. The service plans are sold separate, and it is recommended to purchase at the time-of-service activation. Each part number includes specific cellular service, web portal access and OTA capabilities for the duration defined in the description.
Page 9 1.2.1 Lite Service Plan Feature Content...
Page 10 1.2.2 Standard Service Plan Feature Content...
Page 11 1.2.3 Premium Service Plan Feature Content...
Page 12 4G modem support North American/Americas Bands in 4G and Europe/Australia/New ▪ Zealand/International Bands in 3G. see section 6.2 Modem and Cellular Communications for more information, please contact your Parker Representative for more information. ▪ Service) agreement in place. In addition, the customer must have created a EULA (End User License Agreement) and process for flow down to end users Billing period begins when customer assigns a machine template to the gateway.
Page 13 distracts the driver ▪ as safety hazard. Follow all laws and regulations governing the placement of equipment and mounts. Excess cable can be a tripping hazard. Ensure cable is not draped where it will interfere with ▪ either the driver or passenger as they move within the cab 2.2 Installation Guidelines Gateway can be safely installed on a secured bracket that is robust enough to minimize any ▪...
Page 14 The following guidelines are related to physically attaching the PVSG-IoT-TP*-4GLTE to a vehicle: Mounting Screw Locations. There are a total of 4 mounting screw holes, one at each ▪ corner, as pointed by the red arrows below. Two of the holes are slightly elongated for tolerance purposes.
Page 15 2.5 Suggested Installation Locations To achieve the best performance on the TP1 product, the following installation considerations are recommended. Ideal location as Less ideal but still functional GNSS antennas have an unobstructed sky view Less ideal but still functional Less ideal but still functional 2.6 Designing and Connecting the Vehicle Harness The vehicle manufacturer or integrator is responsible for designing a vehicle harness that mates with the PVSG-IoT-TP*-4GLTE connector(s).
Page 16 To use the remote diagnostic features of the PVSG-IOT-TP*-4GLTE gateway, the diagnostic bus of the gateway must be properly connected to the diagnostic bus of the IQAN control system. Once the vehicle harness is designed, it can be connected to the PVSG-IOT-TP*-4GLTE simply by clicking the mating connectors into the connector ports on the PVSG-IOT-TP*-4GLTE.
Page 17 3.1.2 Pinout The following tables show the pinouts for the connectors: Main Connector Pin-out Function +12V OR +24V VBATT DIGITAL_IN CAN1_H CAN1_L CHASSIS GROUND IGNITION SENSE CAN0_H CAN0_L CHASSIS GROUND DIGITAL OUT CHASSIS GROUND Figure 3: PVSG-IOT-TP*-4GLTE connector GROUND The pins with italicized descriptions are not used in the IQAN Connect solution. It is recommended to plug in the unused pins for the connector.
Page 18 4. Pinout The PVSG-IoT-TP*-4GLTE is powered by a direct battery connection to pin 1, upstream of any main power disconnect switch. The gateway is activated by applying switched power to the ignition sense input pin 6. The PVSG-IoT-TP*-4GLTE operates in a 12 V or 24 V system and can operate from 6.5 V up to 32 V with over-voltage protection at 36 V.
Page 19 5. Power Control Input (Ignition Sense) Damage to equipment! Do not connect inputs directly to unprotected inductive loads such as solenoids or relay coils, as these can produce high voltage spikes that may damage the PVSG-IoT-TP*-4GLTE. If an inductive load must be connected to an input, use protective circuitry such as a diode or transorb.
Page 20 PVSG-IOT-TP*-4GLTE Figure 5: Power control for Sleep Mode function 6. Communication The types of communication available to the PVSG-IoT-TP*-4GLTE are Controller Area Network (CAN), Ethernet, Modem (GSM), Wi-Fi 6.1 Controller Area Network The PVSG-IoT-TP*-4GLTE has 2 CAN communication ports available. The hardware provides controller area network (CAN) communication according to the SAE J1939 specification, making the PVSG-IOT-TP*-4GLTE compatible with CAN based protocol through software.
Page 21 For a list of J1939 connection considerations, refer to the SAE J1939 specifications available through the Society for Automotive Engineers. SAE J1939-11 covers the including cable type, connector type, and cable lengths. The standard variant of the PVSG-IOT-TP*-4GLTE does not have a CAN termination resistor, which assumes that the CAN bus is terminated in the harness.
Page 22 6.2 Modem and Cellular Communications 6.2.1 Modem Specifications The main specifications of the PVSG-IOT-TP*-4GLTE cellular modems interface is listed in the following table: 6.2.1.1 North America/ Central/ South America Cellular Interface America PVSG-IOT-TP*-4GLTE Parameter Description 4G LTE LET FDD Cat 1 Bands 2 ,4, 12 Band 1, 2, 4, 5, 8 HSPA+ (3G)
Page 23 Wi-Fi Local Access Point: Connect mobile devices (PC, phone, tablet) to gateway access ▪ point, perform IQAN real time diagnostic and software OTA updates locally or user the Parker Service Tool. Access the IoT knowledge base for my information on setting up Wi-Fi service and tools: www.community.parker.com The main specifications of the PVSG-IoT-TP*-4GLTE Wi-Fi interface are listed in the following table: (Note 1: Certain governments do not permit operating with all available channels.)
Page 24 6.4 GPS/GNSS Interface The PVSG-IoT-TP*-4GLTE has an onboard GPS chip for calculating geolocation information to be used throughout the cloud application.
Page 25 7. Need Further Assistance? 7.1 Where to find help? Contact the supplier of the PVSG-IoT-TP*-4GLTE gateway or open a ticket with the Parker Support Help Desk 1-888-915-4357 (help) number when looking for assistance on any of the IoT products and services. Also email phsupport@parker.com...
Page 26 This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
Page 27 9. EU Declaration of Conformity...
Page 28 10. Appendix 10.1 Diagram conventions The following symbols are used in the schematic diagrams in this document: Symbol Meaning General input General output Frequency input Analog input Frequency sensor Pulse sensor Resistive sensor General sensor Application switch Load Pull-down resistor Pull-up resistor Battery Fuse...
Page 29 © 2023 Parker Hannifin Corporation PVSG-IoT-TP*-4GLTE User Guide 04/2023 Parker Hannifin Corporation Electronic Motion and Controls Division 850 Arthur Ave Elk Grove Village, IL 60007 phone 800 221 9257 http://www.parker.com/emc...

This manual is also suitable for:

Pvsg-iot-tp1-4glte Pvsg-iot-tp1-4glte-wifi msg