Subscribe to Our Youtube Channel
Related Manuals for Struers TargetX
Summary of Contents for Struers TargetX
- Page 1 TargetX Instruction Manual Original Instructions Doc. no.: 15757026-01_A_en Date of release: 2021.02.12...
- Page 2 Copyright The contents of this manual are the property of Struers ApS. Reproduction of any part of this manual without the written permission of Struers ApS is not allowed. All rights reserved. © Struers ApS 2021.02.12. TargetX...
- Page 3 5.7 Mounting the base plate with tape 5.8 Additional alignment 5.9 Vertical alignment of TargetGrip in the setup station sledge 6 Noise 7 Vibration 8 Preparing the device 8.1 Starting the machine the first time 8.2 Control panel functions - TargetX 8.3 Configuration - TargetX TargetX...
- Page 4 8.3.1 Display contrast 8.3.2 Changing the measurement unit 8.3.3 Language 9 Operating the device 10 Maintenance and service - TargetX 10.1 General cleaning 10.2 Daily 10.3 Weekly 10.4 Spare parts 10.5 Service and repair 10.6 Disposal 11 Technical data 11.1 Technical data - TargetX 11.2 Diagrams...
- Page 5 The device is designed to detect and measure the distance to hidden (internal) targets. TargetX comes with a console and a setup station, which is placed in a suitable X-ray device. TargetX is operated from the console.
- Page 6 2 Safety Struers equipment must only be used in connection with and as described in the instruction manual supplied with the equipment. If the equipment is subjected to misuse, incorrect installation, alteration, neglect, accident or incorrect repair, Struers will accept no responsibility for damage to the user or the equipment.
- Page 7 TargetX is designed for identifying and measuring the distance to hidden targets in specimens for mechanical target preparation. TargetX is intended to be used in combination with a X-ray chamber. The X-ray chamber enable the user to view hidden targets for preparation in a specimen. TargetX is then used to measure the...
- Page 8 3 Getting started distance to the target or targets. The measurement values are afterwards used for target preparation with TargetMaster. TargetX - Front view A Display B Control panel 3.2.1 Base plate Base plate mounted in x-ray chamber 3.2.2 Setup station...
- Page 9 • Place the machine and accessories in their original packaging. Installation WARNING Struers equipment must only be used in connection with and as described in the instruction manual supplied with the equipment. Unpacking Note Struers recommends that all original packaging and fittings are kept for future use.
- Page 10 Take care of your fingers when handling the machine. Wear safety shoes when handling heavy machinery. Note Always lift the machine from beneath. Weight TargetX 13 kg (28.6 lbs) Location CRUSHING HAZARD Take care of your fingers when handling the machine.
- Page 11 5 Installation Note TargetX is supplied with at 5 m (16 ft) connection cable, but you can use an additional connection cable if necessary. Power supply ELECTRICAL HAZARD Switch off the electrical power supply before installing electrical equipment. The machine must be earthed (grounded).
- Page 12 5.5.4 Cable connection Connect one end of the connection cable to the setup station. Connect the other end to the TargetX control unit. Note Align the setup station on two axes before you start using it. Mounting the base plate The base plate ensures that the setup station always is positioned correctly inside your x-ray device.
- Page 13 Turn the table until the reference is plane-parallel with the vertical crosshair. Note the position (x degrees) for future use. Make sure that the table is in this position when you use TargetX. Note Before you start the measuring process with TargetX, the reference edge must always be plane-parallel with the vertical crosshair of the x-ray monitor.
- Page 14 If needed, open the x-ray door, adjust, close the door, start the x-ray, use the TargetX control unit, and repeat this several times while you carry out the following alignment procedure: Locate the reference edge and the alignment plane on TargetGrip.
- Page 15 The first time the machine is switched on, the MAIN MENU screen is shown. Navigating in the display: See Control panel functions - TargetX ►15 Language Select the language you wish to use. If needed, you can change the language at a later date.
- Page 16 Move quickly to the right Tilt to the left Tilt to the right Move to the left Move to the right Configuration - TargetX From the Main menu screen, select the Configuration. From the Configuration screen, select: – Display contrast –...
- Page 17 Select the language you wish to use. If needed, you can change the language at a later date. From the MAIN MENU screen, select CONFIG. > Language. Scroll up or down in the list to select the language of your choice. TargetX...
- Page 18 Rotate the tilt motor shaft back and forth until it clicks into position in TargetGrip. Make sure that TargetX is in target measuring mode . In this mode, Target measuring is highlighted on the display of the TargetX control unit.
- Page 19 10 Maintenance and service - TargetX 12. Fine-position the target plane at the vertical crosshair. 13. Note the target value shown on the TargetX control unit. Transfer this value manually to TargetMaster. 14. If you have multiple targets, use the controls on the control panel to move the specimen to the other targets and note the positions of these targets.
- Page 20 10.5 Service and repair Struers recommends that a regular service check be carried out yearly or after every 1500 hours of use. When the machine is started up, the display shows information about total operation time and the machines service information.
- Page 21 Contact your local authorities for information on the correct method of disposal in accordance with national legislation. For disposal of consumables and recirculation fluid, follow local regulations. 11 Technical data 11.1 Technical data - TargetX Subject Specifications Safety standards See the Declaration of Conformity...
- Page 22 285 mm (11.2") Weight 13 kg (28.6 lbs) 11.2 Diagrams If you wish to view specific information in detail, see the online version of this manual. 11.2.1 Diagrams - TargetX Title TargetX, Block diagram 15753051 A TargetX, Circuit diagram 15753121 A TargetX...
- Page 23 11 Technical data 17753051 A Z501 Power Inlet F1-2 EMC-filter Fuses Switch A502 Power Supply 24Vdc, 4,2A Targetx stander M501, Linear movement A501 Step motor Control Board (X113) NEC V850 uP Circuit 24Vdc in Reset Circuit M502,Rotating movement Non Volatile Memory...
- Page 24 A503 X503 X503 Liquid Crystal Display X110 - Display W505 with LED back light 240 x 128 dots 8x0,25mm2 STRUERS ApS STRUERS ApS STRUERS ApS To length gauge Pederstrupvej 84 Pederstrupvej 84 Pederstrupvej 84 DK-2750 Ballerup DK-2750 Ballerup DK-2750 Ballerup...
- Page 25 Responsibility of the manufacturer The following restrictions should be observed, as violation of the restrictions may cause cancellation of Struers legal obligations. The manufacturer assumes no responsibility for errors in the text and/or illustrations in this manual. The information in this manual is subject to change without notice. The manual may mention accessories or parts not included in the supplied version of the equipment.
- Page 26 Type / Тип / Typ / Type / Typ / Τύπος / Tipo / Tüüp / Tyyppi / Type / Tip / Típus / Tipo / Tipas / Tips / Type / Typ / Tipo / Tipul / Typ / Tip TargetX 05756923 / Typ / 種...
Need help?
Do you have a question about the TargetX and is the answer not in the manual?
Questions and answers