Advertisement
Quick Links
Advertisement
Related Manuals for CP Plus ORANGE F Series
Summary of Contents for CP Plus ORANGE F Series
- Page 1 Quick Start Guide Version 1.0.3...
- Page 2 Welcome Thank you for purchasing our Network camera! This user’s manual is designed to be a reference tool for your system. Please read the following safeguard and warnings carefully before you use this series product! Please keep this user’s manual well for future reference! Important Safeguards and Warnings 1．Electrical safety All installation and operation here should conform to your local electrical safety codes.
- Page 3 is recommended to use the device with thunder proof device in order to improve thunder proof effect. The grounding holes of the product are recommended to be grounded to further enhance the reliability of the camera. Do not touch the CCD (CMOS) optic component directly. You can use the blower to clean the dust or dirt on the lens surface.
- Page 4 Statement Please refer to the actual product for more details; the manual is just for reference. The manual will be regularly upgraded according to the product update; the upgraded content will be added in the manual without prior announcement. Please contact the supplier or customer service if there is any problem occurred when using the device. Please contact the customer service for the latest procedure and supplementary documentation.
- Page 5 Table of Contents Device Framework ..........................5 Device External Cable ......................5 Dimension ..........................6 Device Installation ..........................7 Install SD Card ......................... 7 Fix Device ..........................8 Connect Device Cable ......................9 Adjust Device Angle ....................... 11 Network Configuration ........................12 Initializing Devices ........................
- Page 6 1 Device Framework 1.1 Device External Cable Note The following structure figure is for reference only. It is only used to know the ⚫ functions of cable ports. ⚫ There might be some minor differences between different devices, so please refer to the actual products you purchased.
- Page 7 Port name Connector name Function description Alarm input port receive on-off signal from external ALARM_IN1 alarm source. Alarm output port, output alarm signal to alarm device. I/O Port ALARM_OUT1 ALARM_GND Ground terminal. Table 1-2 1.2 Dimension Note The following figure is for reference only, which is only used to know the device dimension.
- Page 8 2 Device Installation 2.1 Install SD Card Note Please implement the step when the device is equipped with Micro SD card slot ⚫ and it needs to use Micro SD card. Please cut off power before installing Micro SD card. ⚫...
- Page 9 2.2 Fix Device Note ⚫ The following figures are for reference only; please refer to the product for more details. Make sure the bracket installation surface can sustain at least 3X weight of the total ⚫ weight of bracket and camera. Some devices do not support manual focusing lever, please refer to the real ⚫...
- Page 10 2.3 Connect Device Cable ⚫ Connect device corresponding power, video output, audio cable and RS485 control cable well according to requirement, and then use insulated tape to twine the connection respectively to make it waterproof. Connect alarm input and output terminal to external cable according to “Connect ⚫...
- Page 11 Figure 2-4 Figure 2-5 Step 3 Log in WEB interface, make corresponding settings upon alarm input and output on the interface of alarm setup. ⚫ Alarm input of WEB is corresponding to the alarm input of I/O port cable. It is to set corresponding NO, NC input according to the high- and low-level signal generated when alarm happens for alarm input device.
- Page 12 Figure 2-6 Step 1 Keep the convex groove outward and install the rubber ring into the network port, keep the smaller hole of the rubber ring outward and install the fixing rubber ring into the main body of the waterproof connector. Step 2 Pull the network cable without crystal head through main body of waterproof connector, fixing rubber ring and waterproof locking cover, make the crystal head of network cable, and then...
- Page 13 Network Configuration The IP address of all the cameras is the same when leaving factory (default IP192.168.1.250), in order to make the camera get access to the network smoothly, please plan the useable IP segment reasonably according to the actual network environment. Initializing Devices Select one or several uninitialized devices.
- Page 14 Set the initialization parameters for the device. The Device Initialization screen is displayed. The Initialization screen is displayed after initializing is completed. Click the success icon ( ) or click the failure icon ( ) for the details. Click Finish to finish initialization. After the initialization is completed, the status of the devices shows as Initialized on the main user interface of the Tool.
- Page 15 Modifying IP Find the device you want to modify IP, and then click the IP Modification button The Modify IP Address dialog box is displayed. Select the mode for setting the IP address according to the actual situation. Click OK to complete modification.
- Page 16 3.3 Login WEB Interface Note: Different devices may have different WEB interfaces, the figures below are just for reference, please refer to the document <<WEB Operation Manual>> in the disk and the actual interface for more details Step 1 Open IE and input the modified camera IP address in the address bar. Step 2 The login interface is shown below, please input your user name and password (Default user name is admin and password is admin respectively), click “login”.
- Page 17 Figure 3-4 Note: ⚫ This quick start guide is for reference only. Slight difference may be found in user interface. ⚫ All the designs and software here are subject to change without prior written notice. ⚫ All trademarks and registered trademarks mentioned are the properties of their respective owners.
- Page 18 Thank You for choosing CP PLUS!!! Website: - www.cpplusworld.com Email id: - sales@cpplusworld.com; support@cpplusworld.com...
Need help?
Do you have a question about the ORANGE F Series and is the answer not in the manual?
Questions and answers