Do you have a question about the FP-S42B and is the answer not in the manual?
Questions and answers
CANDY TEENG
April 14, 2025
cant pair the device with iphone,where to click allow sharp app to access
1 comments:
Mr. Anderson
April 15, 2025
To allow the Sharp FP-S42B app to access your iPhone for pairing:
1. Download and install the designated Sharp Air App from the provided link. 2. Launch the app and follow the initial setup instructions. 3. Tap the menu button (≡) at the upper left of the app screen. 4. Tap “Register Device”. 5. Tap “Connection with a router” and follow the in-app instructions to connect the air purifier.
Ensure your iPhone is running iOS 12 or later and connected to a compatible Wi-Fi network (2.4GHz or 5GHz).
Page 1
FP-S40B AIR PURIFIER OPERATION MANUAL “Plasmacluster” and “Device of a cluster of grapes” are trademarks of Sharp Corporation. * The number in this technology mark indicates an approximate number of ions supplied into air of 1 cm , which is measured around the center of a room applicable floor area (at 1.2 m height above the floor) when...
Page 24
ENGLISH Thank you for purchasing the SHARP Air Purifier. Please read this manual carefully before using the product. This manual should be kept in a safe place for reference. CONTENTS Important Safety Instructions ..............1 Product Overview ...................3 How To Install ..................5 How To Operate ..................6...
Page 25
It must be replaced, repaired or people often pass by. discarded by the manufacturer or a 6. Do not use the product near the following Sharp authorized Service Center or locations. similarly qualified service agent in order a. Near fires. (Gas appliances, fireplaces, to avoid any hazards.
Page 26
using the product around appliances that it over easily damaged flooring, uneven produce combustion (gas appliances, surfaces, or carpets. etc.). Otherwise it may cause carbon 3. When carrying the product, remove the monoxide poisoning. AC Adapter from the product and then 8.
Page 27
Product Overview Main Body Air Outlet Sensor Filter Only FP-S42B Sensitive Dust Sensor (Inside view of the Only FP-S42B product and on one side) Odor Sensor * Temperature and Humidity Sensor * Only FP-S42B Rear View Operation Panel Two in one HEPA and Deodorizing Filter **...
Page 28
Operation Panel For FP-S42B For FP-S40B Power ON/OFF Button Only FP-S42B Mode Button, Indicators Button and Indicator for Wi- CLEAN ION SHOWER Button, Fi function (See Page 16) Indicator Odor Indicator Cleanliness Indicator • Indicates the product • Indicates the air purity of the room in 5 detects odor.
Page 29
How To Install NOTE Make sure to turn off and unplug the product before installing the filters. Remove the Side Panels and the Pre-Filters. Side Panel Pre-Filter Take out the filters from the plastic bags and then install the filters. Install the Pre-Filters and the Side Panels.
Page 30
How To Operate Start/Stop When the product starts up, it will operate in the previous mode it was running in. ♪~ Stop ♪ Start Fan speed AUTO: The fan speed is automatically switched depending on the amount of impurities in the air.
Page 31
(with the product powered ON or OFF) The Operation Panel is locked while the Child-Lock is set to ON. Press for 3 sec. • You can turn Wi-Fi off even while Child- Lock is ON. (Only FP-S42B) ♪ ♪ Turn off ♪ Switching Plasmacluster Ion...
Page 32
Only FP-S42B Sensor sensitivity Enter the setting mode. (with the product powered OFF) ♪ Press simultaneously for 3 sec. The indicator lights up and displays the current settings. (Example FP-S42B) Sensor sensitivity Bluetooth Auto restart Light control Change settings. Light...
Page 33
How To Maintain NOTE (Benzine, paint thinner, polishing powder or grease, etc.) Make sure to turn Using these items may cause damage off and unplug or discoloration of the product or sensor malfunction. the product before cleaning the product and replacing the filters. Maintenance cycle: Once a month •...
Page 34
Sensors Remove the dust gently with a cleaning tool such as a vacuum cleaner. Temperature and Odor Sensor Humidity Sensor Only FP-S42B Only FP-S42B Sensitive Dust Sensor Sensor Filter If the Sensor Filter is very dirty, wash it with water and dry it thoroughly.
Page 35
When to replace the filters When the Filter Replacement Indicator flashes, replace the filters. Replace the filters. Slow flashing Replace the filters immediately. Rapid flashing Replace the filters according to the instructions on Page 5. Then, follow the steps below to reset (turn off) the Filter Replacement Indicator.
Page 36
Troubleshooting Sensor blocked by something? Check the Before calling for service helpline, sensor area. (Page 3) please review the Troubleshooting • Check the Sensor Filter. If it is clogged or list below, since the problem may dirty, clean it. (Page 10) not be the product malfunctioning.
Page 37
- LOW Indicator - AUTO Indicator Only FP-S42B - MED Indicator Only FP-S42B • Unplug the product, wait one minute, and then plug the product back in. If error still occurs, then contact the Sharp Service Center. EN-13 FP-S42B_S40B.indb FP-S42B_S40B.indb 2024/03/15 2024/03/15...
Page 38
Wi-Fi Function Only FP-S42B Safety precautions of the Wi-Fi functions 6. Communication charges will be incurred WARNING when downloading and using the app. When remotely controlling the air Precautions when using radio purifier waves When operating remotely from outside, you 1.
Page 39
- Mobile router connection following URL. - Tethering connection https://jp.sharp/support/cloud/adapter/ Smart device (ex: smart phone) license_a04.pdf • Minimum software requirements: Android 8 or later / iOS 12 or later Wi-Fi access point (Router)
Page 40
How to use the Wi-Fi function Connect with the app (Sharp Air App) By linking your air purifier with your smart devices, you can enjoy more convenience. Scan the QR code to download and install the designated app. And then follow the steps below for setup.
Page 41
Troubleshooting of the Wi-Fi function The Wi-Fi connection of the air device. purifier and the router is not When changing the router working. • Perform the following steps to reconnect • Check the specifications of the router in the air purifier to a new router. use.
Page 42
How to initialize the Wi-Fi function NOTE When initializing the Wi-Fi function, delete the air purifier registration from the App if it is already registered. Press the Wi-Fi Button for more than 8 seconds. • About 3 seconds after pressing the (with the product powered ON or OFF) button, the air purifier will sound a Press for more...
Page 43
About the Wi-Fi Indicator status Wi-Fi Indicator flashes slowly • It will be in one of the following status. A. The Wi-Fi connection of the air purifier and a router is in setup. B. The connection of the air purifier and a smart device is in setup.
Page 44
Specifications Model FP-S42B Power Supply AC Adapter * Rated Input AC 100 - 240 V 50 - 60 Hz 0.9 A Rated Outlet DC 24.0 V 1.5 A 36.0 W Fan Speed Adjustment Fan Speed (m / h) Rated Power (W) Noise Level (dB) * 1.2 (When Wi-Fi adapter is ON.)
Page 45
Standby Power When the product’s AC Adapter is inserted in a wall outlet it consumes standby power in order to operate electrical circuits. To conserve energy, unplug the AC Adapter when the product is not in use. Model FP-S40B Power Supply AC Adapter * Rated Input AC 100 - 240 V...
Need help?
Do you have a question about the FP-S42B and is the answer not in the manual?
Questions and answers
cant pair the device with iphone,where to click allow sharp app to access
To allow the Sharp FP-S42B app to access your iPhone for pairing:
1. Download and install the designated Sharp Air App from the provided link.
2. Launch the app and follow the initial setup instructions.
3. Tap the menu button (≡) at the upper left of the app screen.
4. Tap “Register Device”.
5. Tap “Connection with a router” and follow the in-app instructions to connect the air purifier.
Ensure your iPhone is running iOS 12 or later and connected to a compatible Wi-Fi network (2.4GHz or 5GHz).
This answer is automatically generated