Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for CreatBot PEEK-250
Summary of Contents for CreatBot PEEK-250
- Page 1 CreatBot PEEK-250 User manual English V1.0 Henan Creatbot Technology Limited - 1 -...
- Page 2 CONTENTS Notice ..........................3 Machine Diagram Front..........................4 Rear ..........................5 Extruder.......................... 6 Printer Operation Leveling Platform......................7 Load Filament ......................8 Unload Filament......................9 Main menu........................10 Detail page........................12 Axis operation......................13 Filament menu......................14 SD Card/U-disk......................15 Info. menu........................16 Setting menu .......................17 Frequently Asked Questions Hardware Troubleshoot....................20 Printing Troubleshoot ....................21...
- Page 3 Please use the filament provided by CreatBot, or high quality filament by third manufacturers. Due to the use of third party inferior material caused by the failure of the printer, the loss will be borne by the user.
- Page 4 Machine Diagram Front Upper door Screen Working status light Front door Filament chamber Water pump Heating status light U-disk port Power switch USB cable port - 4 -...
- Page 5 Machine Diagram Rear Upper cooling circulation fan Back cover Circuit cooling circulation fan Power port - 5 -...
- Page 6 Machine Diagram Extruder Filament tube connector Water cooling tube connector Extruder PCB Cooling fan Filament nut Heating block Nozzle - 6 -...
- Page 7 Printer Operation Leveling Platform Leveling nuts 1. Turn on printer. 2. Click “Move” > “All home” on the screen. 3. Move the extruder by hand to 4 corners of bed, and check the distance between nozzle and bed. Tighten or loosen 4 adjusting nuts below the bed to make sure the distance between nozzle and bed is around 0.1mm with feeler blade or approximately the thickness of one business card in all corners to ensure the bed is Leveled.
- Page 8 Printer Operation Load Filament Preheat head Straightened filament 1. Preheat nozzle. 2. Straighted filament and check the filament do not self-winding. 3. Thread the filament through the filament sensor and manually load the filament until it into the extruder. 4. Click “Load”, until the filament come out from the nozzle. 5.
- Page 9 Printer Operation Unload/Change Filament Unload filament menu Preheat head Pull out filament 1. Enter “ Filament” menu ， click “Unload” . 2. Wait for the nozzle heated to the suitable temperature. 3. After reaching temperature, extruder will extrude a little filament, then unload the filament from extruder.
- Page 10 Printer Operation Touch screen Main Menu 210 ° C Touch and set up the temp of the nozzle. Preset nozzle temperature 210 ° C Current nozzle temperature 25 ° C 25 ° C 110 ° C Touch and set up the temp of the hotbed. Preset platform temperature 110 °...
- Page 11 Printer Operation Touch screen Main Menu preheat Open U-disk Cool down USB unavailable Filament menu bed up Move axis bed down resume stop pause Setting - 11 -...
- Page 12 Printer Operation Touch screen Detail page Adjust. During printing, you can click itto adjust the print speed fan speed andthe extrusion. Current printing progress pause stop change 100% print speed：100% flow rate：100% 100% colling fan speed：100% 100% - 12 -...
- Page 13 Printer Operation Axis operation Minimum units Move X to home Move Y to home Move Z to home All axis to home Move Y axis Move X axis Z down/up Back X,Y,Z current position of hotend. - 13 -...
- Page 14 Printer Operation Filament menu extruder Extrude filament Retract filament Back Click and enter a value load/unload Adjust value when extrude/retract filament - 14 -...
- Page 15 Printer Operation SD Card/U-disk print file2.gcode file2.gcode Click and choose a file to print Last page Superior menu Next page Back - 15 -...
- Page 16 Printer Operation Info. page 0000:00:00 6.1.XXXXXX 6.1.0 Time used Print time used 0000:00:00 Firmware Firmware version 6.1.XXXXXX UI version UI version 6.1.0 Back - 16 -...
- Page 17 Printer Operation Setting menu X/Y/Z and exturder motor setting (range:5-9999) Save Back The values in the picture are not real values, the real values refer to the printer default values - 17 -...
- Page 18 Printer Operation Setting menu sink fan speed (range:1-100) cooling fan speed (range:1-100) head temperature (range:0-420) hotbed temperature (range:0-100) - 18 -...
- Page 19 Printer Operation Setting menu Enter the WiFi name and password, and click Connect. The printer will automatically connect to WiFi. Only supports 2.4GHz Wi-Fi. - 19 -...
- Page 20 Frequently Asked Questions Hardware Troubleshoot 1. Display "MINTEMP" ? The environment is too low, or temperature sensor is damaged, please keep the room temperature above 0 ℃ . 2. Display "MAXTEMP" ? Temperature of nozzle or bed too high, or temperature sensor is damaged, please keep their temperature in a suitable range.
- Page 21 Printing Troubleshoot not over 120℃, and you can close the bed above 100mm except printing ABS or other high-temperature required filaments. 3. The model not stick on the platform ? Please paste masking paper or Kapton tape on the platform, or the nozzle is too far away from the platform, or the bottom of the model is not flat.
- Page 22 Quality · Experience · Ser vice Henan Creatbot Technology Limited Website: www.CreatBot.com Email: sales@creatbot.com Address: No.150 Lamei Road, Zhongyuan District, Zhengzhou City, Henan Province, China...
Need help?
Do you have a question about the PEEK-250 and is the answer not in the manual?
Questions and answers