Page 3
Table of contents Table of contents General information..........................5 1.1 Symbols and signal words....................... 5 Safety instructions............................. 8 Features and scope of delivery......................13 Installation..............................15 Starting up..............................22 Connections and controls........................24 Operating..............................28 7.1 Starting up the device........................28 7.2 Main menu............................
Page 4
Table of contents 7.12 Reset to factory defaults......................55 Technical specifications........................56 Plug and connection assignment....................58 Cleaning............................... 59 Protecting the environment......................60 70th Stage TRI LED Bundle Complete LED Lighting Set...
Page 5
Our products and documentation are subject to a process of continuous development. They are therefore subject to change. Please refer to the latest version of the documentation, which is ready for download under www.thomann.de. 1.1 Symbols and signal words In this section you will find an overview of the meaning of symbols and signal words that are used in this document.
Page 6
General information Signal word Meaning DANGER! This combination of symbol and signal word indicates an immediate dangerous situation that will result in death or serious injury if it is not avoided. WARNING! This combination of symbol and signal word indicates a pos‐ sible dangerous situation that can result in death or serious injury if it is not avoided.
Page 7
General information Warning signs Type of danger Warning – suspended load. Warning – danger zone. 70th Stage TRI LED Bundle Complete LED Lighting Set...
Page 8
Safety instructions Safety instructions Intended use This device is intended for use as an electronic lighting effect by means of LED technology. The device is designed for professional use only and is not suitable for use in households. Use the device only as described in this user manual.
Page 9
Safety instructions DANGER! Danger to life due to electric current! Within the device there are areas where high voltages may be present. Never remove any covers. There are no user-serviceable parts inside. Do not use the device when covers, safety equipment or optical components are missing or damaged. DANGER! Danger to life due to electric current! A short circuit could lead to a fire hazard and risk of death.
Page 10
Safety instructions NOTICE! Risk of fire due to covered vents and neighbouring heat sources! If the vents of the device are covered or the device is operated in the immediate vicinity of other heat sources, the device can over‐ heat and burst into flames. Never cover the device or the vents. Do not install the device in the immediate vicinity of other heat sources.
Page 11
Safety instructions NOTICE! Risk of short circuit due to changing the connection wiring during operation! If connection cables of individual spots are removed or replaced during operation, short circuits may occur that can irreparably damage the device. Always disconnect the device from the mains before making any changes to the wiring. NOTICE! Damage to the device by disconnecting LED spots during operation! If individual LED spots are disconnected from the device during operation, the device can get damaged.
Page 12
Safety instructions NOTICE! Possible damage due to leaking batteries! Batteries can leak and cause permanent damage to the device. Take the batteries out of the device if it is not going to be used for an extended period of time. 70th Stage TRI LED Bundle Complete LED Lighting Set...
Page 13
Complete can be easily controlled via the supplied foot switch or DMX 512. Special features of the device: Special edition of the classic lighting set to mark Thomann’s 70th anniversary Special edition with new innovative sound mode 4 LED spots with 7 3 W RGB TRI-Colour LEDs each (28 in total) Control via DMX 512 or foot switch (available via foot switch: automatic mode, sound-to- light mode, freeze &...
Page 14
Features and scope of delivery T-bar with 4 LED spots, lighting stand (max. height 240 cm), foot switch with 4 buttons, transport bag for light and stand (included in the scope of delivery) Remote control (item no. 354223, optionally available) For technological reasons, the light output of LEDs decreases over their lifetime.
Page 15
Installation Installation Unpack and check carefully there is no transportation damage before using the unit. Keep the equipment packaging. To fully protect the product against vibration, dust and moisture during transportation or storage use the original packaging or your own packaging material suitable for transport or storage, respectively.
Page 16
Installation NOTICE! Damage to the device by disconnecting LED spots during operation! If individual LED spots are disconnected from the device during operation, the device can get damaged. Operate the device only when all LED spots are connected. Always disconnect the device from the mains before removing the LED spots. NOTICE! Risk of overheating and fire due to inadequate distance and bad ventilation! If the distance between the light source and the illuminated surface is too short or...
Page 17
Installation NOTICE! Potential property damage due to unsuitable stands! If the device is mounted on an unsuitable stand, there is a risk that the stand will fall over and cause damage. Only use stands whose maximum bearing capacity is at least as high as the weight of the device.
Page 18
Installation Pre-mounted spots The four spots (1 … 4, left to right) are pre-mounted on the T-bar. All you need to do is attach the stand and connect the foot switch unit. ö ö & & 70th Stage TRI LED Bundle Complete LED Lighting Set...
Page 19
Installation 1 Locking screws to fix the height and inclination angle 2 Threads for attaching additional effects units or for hanging using the C-hooks 3 Locking screw for fixing the spots on the T-bar and the horizontal orientation (dispersion direction) 4 Electrical connection of the spot at the T-bar (pre-mounted) 5 6.35-mm jack socket for connecting the foot switch unit.
Page 20
Installation Inserting the battery into the Push the lock of the battery holder towards the centre of the housing and pull out the battery remote control holder like a drawer. Insert the batteries. The battery is correct if the positive pole points to the housing base of the remote control.
Page 21
Installation Please note that this device must not be connected to a dimmer. 70th Stage TRI LED Bundle Complete LED Lighting Set...
Page 22
Starting up Starting up Create all connections while the device is off. Use the shortest possible high-quality cables for all connections. Take care when running the cables to prevent tripping hazards. Connections in DMX mode Connect the DMX input of the device to the DMX output of a DMX controller or another DMX device.
Page 23
Starting up Connections in master/slave When you configure a group of devices in master/slave mode, the first unit will control the mode other units for an automatic, sound-activated, synchronized show. This function is ideal when you want to start a show immediately. Connect the DMX output of the master device to the DMX input of the first slave device.
Page 24
Connections and controls Connections and controls Front panel ö & 70th Stage TRI LED Bundle Complete LED Lighting Set...
Page 25
Connections and controls 1 Rubber panel plug for the power supply with fuse holder 2 [Mic] | Built-in microphone for the “sound control” operating mode 3 [Mode] | Activates the main menu and toggles between menu items. Closes an open submenu. 4 Display 5 [DOWN] | Decreases the displayed value by one.
Page 26
Connections and controls Foot switch unit (item no. 279058) ö 1 [Auto Run/Program] | Activates “Automatic” mode (playback of pre-programmed automatic shows). 2 [Sound Active] | Activates “Sound control” mode (playback of sound-controlled automatic shows). 3 [Freeze] | Pauses the running show (“freeze”) and resumes it after a break. 4 [Blackout] | Blacks out all LEDs or turns them back on again.
Page 27
Connections and controls Infrared remote control Since the universal remote control can be used for several device types, some buttons may not (item no. 354223, be assigned and therefore have no function. optionally available) 1 [AUTO] | Activates “Automatic” mode. ö...
Page 28
Operating Operating 7.1 Starting up the device Connect the unit to the power grid to start the operation. After a few seconds the display shows a running reset. Then the unit is ready for use. 7.2 Main menu Press [Mode] to activate the main menu and select an operating mode. Use [Setup] to select further options.
Page 29
Operating “Pre-programmed automatic A pre-programmed automatic show can only be activated if the device is operating in stand- show” operating mode alone mode or as master in a master/slave combination. This setting is only relevant if the device is not controlled via DMX. Press [Mode] repeatedly until the display shows ‘Pr.xx’...
Page 30
Operating Display Description ‘Co.03’ Blue ‘Co.04’ Cold white ‘Co.05’ Amber ‘Co.06’ Orange ‘Co.07’ Yellow ‘Co.08’ Purple ‘Co.09’ Pink ‘Co.10’ Cyan ‘Co.11’ Light red ‘Co.12’ Light green ‘Co.13’ Light blue ‘Co.14’ Warm white To adjust the flash frequency, press [Setup]. Now use [Up] and [Down] to select a value between ‘FL.00’...
Page 31
Operating Settings for programmes 02 to 23: To adjust the speed of the selected auto show, press [Setup] repeatedly until the display shows ‘SP.xx’ . Now use [Up] and [Down] to select a value between ‘SP.01’ (slow) and ‘SP.99’ (fast) or ‘SPFL’...
Page 32
Operating In automatic mode the saved programmes run sequentially. Press the [AUTO] button several times to start the automatic sequence from a specific programme. There is however no way to permanently specify a specific programme as the starting programme. DMX mode This setting is only relevant when the device is controlled via DMX.
Page 33
Operating Display Description ‘SO.01’ … ‘SO.03’ Gentle effects ‘SO.04’ … ‘SO.21’ Dynamic effects ‘SO.22’ Collection of gentle effects ‘SO.23’ Collection of dynamic effects ‘SO.24’ Collection of all effects Press [Setup]. Now you can adjust the sensitivity for the sound control. Use [Up] and [Down] to select a value between 0 (low sensitivity) and 50 (high sensitivity), display shows ‘SU.xx-FL(00)’...
Page 34
Operating Constant monochrome pattern A constant monochrome pattern can only be activated when the unit is operating in stand alone mode or as master in a master / slave combination. This setting is only relevant if the device is not controlled via DMX. Press [Mode] repeatedly until the display shows ‘Colr’...
Page 35
Operating Settings Press [Mode] repeatedly until the display shows ‘Set’ . Press [Setup]. Use [Up] and [Down] to select a setting. Display Meaning ‘Cu.SE’ Dimmer curves ‘di.SP’ Dimmer speed ‘Pi.dl’ Running direction of the lights ‘-rst’ Restore factory setting ‘FAIL’ Behaviour in case of DMX signal failure ‘LocK’...
Page 36
Operating Display Meaning ‘Cu-3’ Inv Square Law ‘Cu-4’ S-Type Press [Mode] repeatedly until the display shows ‘di.SP’ . Press [Setup]. You can choose the speed ‘FASt’ (fast) or ‘SLO’ (slow). Press [Mode] repeatedly until the display shows ‘Pi.dl’ . Press [Setup]. Use [Up] and [Down] to select a setting between ‘Nor’...
Page 37
Operating 7.3 Menu overview Menu 1 Menu 2 Menu 3 Menu 4 auto au.01...03 sp.01-fl(81) fl.00...99 pr.01 co.00...14(01) fl.00...99 pr.02-23 sp.01...fl(81) SLAVE d.001...512 3/4/6/12/15/19 d--- soud so.01...24 su.00-fl(50) Colr r.000...255 g.000...255 b.000...255 70th Stage TRI LED Bundle Complete LED Lighting Set...
Page 38
Operating cu.se cu-1/2/3/4 di.sp fast/slo pi.dl nor/inv -rst no/yes fail off/hold lock on/off info v.x.x.x 70th Stage TRI LED Bundle Complete LED Lighting Set...
Page 39
Operating 7.4 Functions in 3-channel DMX mode Channel Value Function 0…255 Red intensity (0% to 100%) for all LEDs 0…255 Green intensity (0% to 100%) for all LEDs 0…255 Blue intensity (0% to 100%) for all LEDs 7.5 Functions in 4-channel DMX mode Channel Value Function...
Page 40
Operating Channel Value Function 76…85 Pre-programmed automatic show no. 07 86…95 Pre-programmed automatic show no. 08 96…105 Pre-programmed automatic show no. 09 106…115 Pre-programmed automatic show no. 10 116…125 Pre-programmed automatic show no. 11 126…135 Pre-programmed automatic show no. 12 136…145 Pre-programmed automatic show no.
Page 41
Operating Channel Value Function 236…245 Pre-programmed automatic show no. 23 246…255 Sound-controlled show 0…25 Sound-controlled show no. 01 26…35 Sound-controlled show no. 02 36…45 Sound-controlled show no. 03 46…55 Sound-controlled show no. 04 56…65 Sound-controlled show no. 05 66…75 Sound-controlled show no. 06 76…85 Sound-controlled show no.
Page 42
Operating Channel Value Function 156…165 Sound-controlled show no. 15 166…175 Sound-controlled show no. 16 176…185 Sound-controlled show no. 17 186…195 Sound-controlled show no. 18 196…205 Sound-controlled show no. 19 206…215 Sound-controlled show no. 20 216…225 Sound-controlled show no. 21 226…235 Sound-controlled show no.
Page 43
Operating Channel Value Function Channel 2 = 246…255 0…255 Increasing sensitivity 7.6 Functions in 6-channel DMX mode Channel Value Function 0…255 Red intensity (0% to 100%) for all LEDs of spots 1 and 2 0…255 Green intensity (0% to 100%) for all LEDs of spots 1 and 2 0…255 Blue intensity (0% to 100%) for all LEDs of spots 1 and 2 0…255...
Page 44
Operating 7.7 Functions in 12-channel DMX mode Channel Value Function 0…255 Red intensity (0% to 100%) for all LEDs of spot 1 0…255 Green intensity (0% to 100%) for all LEDs of spot 1 0…255 Blue intensity (0% to 100%) for all LEDs of spot 1 0…255 Red intensity (0% to 100%) for all LEDs of spot 2 0…255...
Page 45
Operating 7.8 Functions in 15-channel DMX mode Channel Value Function 0…255 Dimmer (0% to 100%) 0…10 No function 11…255 Strobe effect, increasing speed 0…255 Red intensity (0% to 100%) for all LEDs of spot 1 0…255 Green intensity (0% to 100%) for all LEDs of spot 1 0…255 Blue intensity (0% to 100%) for all LEDs of spot 1 0…255...
Page 46
Operating Channel Value Function 0…255 Blue intensity (0% to 100%) for all LEDs of spot 4 0…39 No function 40…75 Pixel Direction Normal 76…111 Pixel Direction Invert 112…147 Linear 148…183 Square Law 184…219 Inv Square Law 220…255 S-Type 70th Stage TRI LED Bundle Complete LED Lighting Set...
Page 47
Operating 7.9 Functions in 19-channel DMX mode Channel Value Function 0…255 Dimmer (0% to 100%) 0…10 No function 11…255 Strobe effect, increasing speed 0…17 No function 18…34 35…51 R(0)G(255)B(0) 52…68 R(0)G(0)B(255) 69…85 R(255)G(255)B(255) 86…102 R(255)G(150)B(0) 103…119 R(255)G(180)B(0) 120…136 R(255)G(255)B(0) 137…153 R(255)G(0)B(255) 154…170 R(255)G(0)B(140)
Page 48
Operating Channel Value Function 188…204 R(255)G(50)B(205) 205…221 R(200)G(230)B(50) 222…238 R(50)G(255)B(250) 239…255 R(255)G(255)B(75) 0…25 No function 26…35 Pre-programmed automatic show no. 02 36…45 Pre-programmed automatic show no. 03 46…55 Pre-programmed automatic show no. 04 56…65 Pre-programmed automatic show no. 05 66…75 Pre-programmed automatic show no.
Page 49
Operating Channel Value Function 136…145 Pre-programmed automatic show no. 13 146…155 Pre-programmed automatic show no. 14 156…165 Pre-programmed automatic show no. 15 166…175 Pre-programmed automatic show no. 16 176…185 Pre-programmed automatic show no. 17 186…195 Pre-programmed automatic show no. 18 196…205 Pre-programmed automatic show no.
Page 50
Operating Channel Value Function 56…65 Sound-controlled show no. 05 66…75 Sound-controlled show no. 06 76…85 Sound-controlled show no. 07 86…95 Sound-controlled show no. 08 96…105 Sound-controlled show no. 09 106…115 Sound-controlled show no. 10 116…125 Sound-controlled show no. 11 126…135 Sound-controlled show no.
Page 51
Operating Channel Value Function 216…225 Sound-controlled show no. 21 226…235 Sound-controlled show no. 22 236…245 Sound-controlled show no. 23 246…255 Sound-controlled show no. 24 Function depending on setting of channel 2 Channel 2 = 0…25 No function Channel 2 = 26…245 0…255 Increasing speed Channel 2 = 246…255...
Page 52
Operating Channel Value Function 0…255 Blue intensity (0% to 100%) for all LEDs of spot 2 0…255 Red intensity (0% to 100%) for all LEDs of spot 3 0…255 Green intensity (0% to 100%) for all LEDs of spot 3 0…255 Blue intensity (0% to 100%) for all LEDs of spot 3 0…255...
Page 53
Operating 7.10 Functions of foot switch Operating mode ‘Automatic’ Press the foot switch [Auto Run] to start the playback of the preprogrammed automatic shows. Each time you press the switch, the next show will be called up. Operating mode ‘Sound-con‐ Press the foot switch [Sound Active] to start the playback of the sound-controlled automatic trol’...
Page 54
Operating Direct selection of a static colour Use the numeric keys of the remote control to select a static colour directly. This setting is only relevant if the device is not controlled via DMX. Value Static colour Cyan Purple Pink Orange Cool white Light red...
Page 55
Operating Value Static colour Blue Amber 7.12 Reset to factory defaults Proceed as follows to reset the device to factory defaults: Switch off the device. Switch the device on again and hold the buttons [Mode] and [Setup] pressed for about 2 seconds.
Page 56
Technical specifications Technical specifications Light source 28 × 3in1 LED, 3 W RGB each Optical properties Beam angle approx. 40° Control DMX, foot switch, infrared remote control (optional) Number of DMX channels Input connections Power supply C14 rubber panel plug DMX control XLR panel socket, 3-pin Foot switch unit...
Page 57
Technical specifications Mounting options Stand Dimensions W × H × D (spots including T-bar) 1,200 mm × 330 mm × 70 mm Height, max. (T-bar plus stand) 2,400 mm Weight 16 kg Ambient conditions Temperature range 0 °C…40 °C Relative humidity 20%…80% (non-condensing) Further information Spotlight included...
Page 58
Plug and connection assignment Plug and connection assignment Introduction This chapter will help you select the right cables and plugs to connect your valuable equip‐ ment so that a perfect light experience is guaranteed. Please take our tips, because especially in ‘Sound & Light’ caution is indicated: Even if a plug fits into a socket, the result of an incorrect connection may be a destroyed DMX controller, a short circuit or ‘just’...
Page 59
Cleaning Cleaning Optical lenses Clean the optical lenses, that are accessible from the outside, regularly in order to optimize the light output. The frequency of cleaning depends on the operating environment: wet, smoky or particularly dirty surroundings can cause more accumulation of dirt on the optics of the device.
Page 60
Protecting the environment Protecting the environment Disposal of the packing material Environmentally friendly materials have been chosen for the packaging. These materials can be sent for normal recycling. Ensure that plastic bags, packaging, etc. are disposed of in the proper manner. Do not dispose of these materials with your normal household waste, but make sure that they are collected for recycling.
Page 61
Repairing a device or passing it on to another user is an ecologically valuable alternative to disposal. You can return your old device to Thomann GmbH at no charge. Check the current conditions on www.thomann.de. If your old device contains personal data, delete those data before disposing of it.
Page 62
Notes 70th Stage TRI LED Bundle Complete LED Lighting Set...
Need help?
Do you have a question about the STAIRVILLE 70th Stage TRI LED Bundle Complete and is the answer not in the manual?
Questions and answers