Charmglow 720-0536 Assembly & Operating Instructions

Hide thumbs

page of 54

/ 54
Bookmarks

Quick Links

Download this manual

This Owner's Manual is provided and hosted by Appliance Factory Parts.

Charmglow - Old 720-0536 -

Old

Owner's Manual

Shop genuine replacement parts for Charmglow - Old

720-0536 - Old

Find Your Charmglow - Old Grill Parts - Select From 3 Models

-------- Manual continues below --------

Need help?

Do you have a question about the 720-0536 and is the answer not in the manual?

Questions and answers

Summary of Contents for Charmglow 720-0536

Page 1 This Owner's Manual is provided and hosted by Appliance Factory Parts. Charmglow - Old 720-0536 - Owner's Manual Shop genuine replacement parts for Charmglow - Old 720-0536 - Old Find Your Charmglow - Old Grill Parts - Select From 3 Models -------- Manual continues below --------...
Page 2 ASSEMBLY & OPERATING INSTRUCTIONS Model: 720-0536 FOR OUTDOOR USE ONLY FOR PROPANE GAS USE ONLY F20Y07P-1 This instructions manual contains important information necessary for the proper assembly and safe use of the appliance. Read and follow all warnings and instructions before assembling and using the appliance...
Page 3 Table of Contents Safety Instruction ..... Gas Conversion ..... . 29-32 Assembly Instruction .
Page 4 Safety Instruction WARNING ELECTRICAL GROUNDING INSTRUCTIONS This appliance (rotisserie motor) is equipped with a plug and should be plugged directly into a properly grounded receptacle. When installed, must be electrically grounded in accordance with local codes or in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70 or the Canadian Electrical Code, CSA C22.1 DO NOT cut or remove the grounding prong from this plug.
Page 5 Safety Instruction WARNING CAUTION: Beware of Flashback Do not try lighting this appliance without reading the CAUTION: Spiders and small insects occasionally “LIGHTING INSTRUCTIONS” section of this manual. spin webs or make nest in the grill burner tubes during transit and warehousing.
Page 6 Safety Instruction LP-Gas Supply System PROPER PLACEMENT AND CLEARANCE OF A 20lb tank of approximately 1/4 inches in diameter by 18-1/4 GRILL inches high is the maximum size LP gas tank to use. This safety feature prevents the tank from being overfilled, which •Never use your gas grill in a garage, porch, shed, can cause malfunction of the LP gas tank, regulator and/or grill.
Page 7 Safety Instruction SAFETY PRACTICES TO AVOID PERSONAL WARNING INJURY Your grill will get very hot. Never lean over the cooking area while using your grill. Do not touch When properly cared for, your grill will provide safe, cooking surfaces, grill housing, lid or any other grill reliable service for many years.
Page 8 Safety Instruction Do not heat unopened food containers. A build-up of Do not use the grill to cook excessively fatty meats or pressure may cause the containers to burst. other products which promote flare – ups. Use a covered hand when opening the grill lid. Do not operate the grill under unprotected combustible constructions.
Page 9 Assembly Instruction PLEASE READ THESE INSTRUCTIONS CAREFULLY AND FOLLOW STEP BY STEP ► Propane Tank is not include ► Phillips head Screwdriver (not provided) STEP 1:The screws used to attach the left side shelf supporting bar are already screwed into the left panel (see the figure below, altogether 6 screws).
Page 10 Assembly Instruction Continued STEP 2: secure the push bar to the side shelf. The screws used to attach the push bar to the side shelf have already screwed into the push bar, remove the screws and align the holes to the side shelf, and re-screw into the side shelf from inside out...
Page 11 Assembly Instruction Continued STEP3. The screws used to attach the side shelf to the supporting bar have already screwed into the supporting bar, you just need to remove the upper screw and align the side shelf to the supporting bar, re-screw into the supporting bar. The side shelf can be easily folded and extended after this assembly.
Page 12 Assembly Instruction Continued STEP 4: Battery is inserted for the Rotisserie burner . To install the battery, turn the ignition button cap counterclockwise and remove it. Replace the ignition button cap after the battery is installed.
Page 13 Assembly Instruction Continued STEP 5: Attach propane gas tank to regulator inlet fitting by turning the regulator clockwise as shown in figure below. LP gas cylinder must be fitted with a listed overfill prevention device (OPD). Open the door and pull out the tray, place the gas tank cylinder in the tank tray , then use retention kit that showed as below diagram to secure the tank cylinder .
Page 14 Assembly Instruction Continued STEP 6: The screws for rotisserie drive motor bracket are screwed into the right side of the grill housing. Remove the screws and install the rotisserie motor bracket as shown in the figure below. Assemble the rotisserie skewer as shown in the figure below.
Page 15 To Match Light the Grill If the burner will not light after several attempts then the burner can be match lit. If you have attempted to light the main burners with the igniter, allow 5 minutes for any accumulated gas to dissipate. Insert a match into the lighting rod.
Page 16 Gas Hook - Up NEVER CONNECT AN UNREGULATED GAS QCC1 in the standard for compressed gas SUPPLY LINE TO THE APPLIANCE. USE cylinder valve outlet and inlet connection THE REGULATOR/HOSE ASSEMBLY ANSI/CGA-V-1. SUPPLIED. Manifold pressure: 11”(27.94cm) water This is a liquid propane configured grill. Do not column (W.C.).
Page 17 Gas Hook - Up 5. When connecting regulator assembly to the 7. If you have a gas connection leak you valve, hand tighten the quick coupling nut cannot repair, turn gas OFF at supply tank, clockwise to a complete stop. Do not use a disconnect fuel line from your grill and call wrench to tighten.
Page 18 Leak Testing GENERAL Only those parts recommended by the manufacturer should be used on the grill. Although all gas connections on the grill are leak tested at the factory prior to shipment, a complete Substitution will void the warranty. Do not use gas tightness check must be performed at the the grill until all connections have been checked installation site due to possible mishandling in...
Page 19 CAUTIONS Place dust cap on cylinder valve outlet when the cylinder is not in use. Only install the type of dust cap on the cylinder valve outlet that is provided with the cylinder valve. Other types of caps or plugs may result in leakage of propane. The gas must be turned off at the supply cylinder when the unit is not in use.
Page 20 Operating Instructions GENERAL USE OF THE GRILL AND WARNING: IMPORTANT! ROTISSERIE USING THE SIDE BURNER: Each main burner is rated at 10,000 Btu/hr. Inspect the gas supply hose prior to turning The main grill burners encompass the entire the gas “ON”. If there is evidence of cuts, cooking area and are side ported to wear or abrasion, it must be replaced prior minimize blockage from falling grease and...
Page 21 Operating Instructions Continued USING THE OVEN OVEN VENT: Do not block the ducts at the rear of the range when cooking in the oven. It is important that the flow of hot air from the oven and fresh air into the oven burner never be interrupted. Avoid touching the vent openings or nearby surfaces during oven or broiler operation –...
Page 22 Operating Instructions Continued CAUTION: PLEASE TAKE OFF THE WARMING RACK WHEN USING THE ROTISSERIE BURNER. THE HIGH HEAT COMING FROM THE ROTISSERIE BURNER MAY CAUSE THE WARMING RACK TO BEND. Grill Lighting Instructions WARNING: IMPORTANT! Never substitute regulators and hose assembly for those supplied with the grill.
Page 23 Grill Lighting Instructions continued TO LIGHT THE GRILL BURNER: If you’ve just attempted to light the burner with the igniter, allow 5 minutes for any Make sure all knobs are “OFF” then turn on accumulated gas to dissipate. Keep your face the gas supply from the LP tank.
Page 24 Grill Lighting Instructions continued FLAME CHARACTERISTICS Check for proper burner flame characteristics. Each burner is adjusted prior to shipment; however, variations in the Burner flames should be blue and stable with local gas supply may take minor no yellow tips, excessive noise, or lifting. If adjustments necessary.
Page 25 Motor Instruction • TO USE MOTOR SAFELY, PLEASE READ WARNING BEFORE PRIOR TO USE ROTISSERIE DRIVE MOTOR USE ONLY FOR OUTDOORS, DO NOT EXPOSE TO RAIN. CAUTION: TO ENSURE CONTINUED PROTECTION AGAINST RISK OF ELECTRIC SHOCK, CONNECT TO PROPERLY GROUNDED OUTLETS ONLY, TO REDUCE THE RISK OF ELECTRIC SHOCK, KEEP EXTENSION CORD CONNECTION DRY AND OFF THE GROUND.
Page 26 Lighting Illustration Main & Side Burner Lighting Illustration Rotisserie Burner or Searing Burner Lighting Illustration Step 1. Step to light the Rotisserie Burner : Make sure the Lid is open Push and turn the rotisserie knob to “ON” position and hold down for 3-4 seconds then push electronic ignition button at the same time, until burner is lit.
Page 27 Lighting Illustration Continued Step 1.Push & Turn the Knob to light the oven Step 2.After the burner is lit, adjust the Burner, it may take about 36-50 seconds to light temperature the Oven burner as you need Converting to Natural Gas This Grill is portable and configured for use with Liquid Propane (LP Gas), which is delivered to the grill from removable tanks (LP tanks and their use are covered elsewhere in this manual).
Page 28 Instruction for Converting to Natural Gas Continued TOOLS NEEDED: A- 6mm & 7mm LONG SOCKET & DRIVER B-PHILLIPS & C-FLAT-HEAD SCREWDRIVER D-ADJUSTABLE WRENCH E-10mm OPEN END WRENCH F-VICE GRIPS Step 1: Replace Main Burner Orifice a. Remove cooking-grids & flame tamers b.
Page 29 Step 1. Remove the side burner lid, and side burner base Use a pinchers to pull out the clip on the hinge on either side, then draw out the hinge from another side Remove the screws on the base, all together 4 screws, 2 on each side Step 2.
Page 30 Gas Conversion Step 3: Replace Rear Burner Orifice a. Remove rear baffle from bowl Assembly b. Grasp brass elbow with vice grip c. With 10 mm wrench remove LP orifices and replace with NG orifice(1.55mm) d. Replace rear baffle...
Page 31 Gas Conversion continued Step 4: Replace Searing Burner Orifice a. Remove the thermocouple cover at back of fire-box, then remove the thermocouple. Remove the COTTER-PIN under Searing burner and remove the burner b. Locate LP-Orifice (inside front wall of firebox) & and use 7mm long socket to replace with NG-Orifice (1.9mm) c.
Page 32 Gas Conversion continued Step 4: Replace Oven Burner Orifice a. Remove Back Access Panel from the rear panel (Fig 1) b. Grasp brass elbow with vice grip or plyers (Fig 2) c. With 10 mm wrench, remove LP orifice and replace with NG orifice(1.98mm) (Fig 3 & 4) d.
Page 33 Gas Conversion Continued Step 5: Remove Regulator a. Use adjustable wrench to remove existing LP Gas regulator and Hose assembly. b. If you are replacing an existing Natural Gas Grill, the supply hose that supplied Natural Gas to the old Grill will work with your new Grill. c.
Page 34 Care and Maintenance MAIN GRILL BURNER CLEANING STAINLESS STEEL Ensure the gas supply is off and the knobs are The grill is made from non-rusting and 430 in the “OFF” position. Make sure the grill is cool. stainless steel. There are many different Clean the exterior of the burner with a wire stainless steel cleaners available.
Page 35 Care and Maintenance Continued HOW TO REPLACE MAIN BURNER STAINLESS STEEL : There are many different stainless steel Step 1. Insert the burner onto the orifice. cleaners available. Always use the mildest cleaning procedure first, scrubbing in the direction of the grain. Do not use steel wool as it will scratch the surface.
Page 36 Oven Maintenance and Cleaning CLEANING INSIDE THE OVEN: Bottom of the oven is partially covered by the Oven Bottom Cover and flame tamer. This cover may be removed for cleaning by lifting it up and out of the oven. The interior parts of the oven are porcelain coated. They are all easily cleaned. Care should taken so as not to drip water into the small holes (ports) on the burner.
Page 37 Remove the oven door The oven door can be removed for cleaning. Please see the following illustrations. Oven Door Disassembling as shown in the figure: 2.Keeping the door at 30-45 degrees angle, lift 1.Slide the locking bracket (Left & Right each) of the door, pull it up &...
Page 38 Trouble Shooting SPIDER AND INSECT WARNING!!! WHEN TO LOOK FOR SPIDERS You should inspect the burners at least once a year or immediately after any of the Checking and cleaning burner/ venturi tubes following conditions occur: for insects and insect nests. A clogged tube can lead to a fire beneath the grill.
Page 39 Trouble Shooting continued PREHEATING: The grill lid should be in a closed position during the preheat time period. It is necessary to preheat the grill for a short time before cooking certain foods, depending on the type of food and the cooking temperature. Food that requires a high cooking temperature needs a pre-heat period of five minutes;...
Page 40 Trouble Shooting continued PROBLEM SOLUTION When attempting to light my grill, it will not • Make sure you have a spark while you are trying to light light immediately. the burner (if no spark) • Ensure that the wire is connected to the electrode assembly.
Page 41 Trouble Shooting continued Rotisserie motor will not turn • Ensure the motor is connected to a properly grounded power supply. • Ensure the on / off switch is in the on position. • Ensure that the spit is fully inserted into the rotisserie motor •...
Page 42 Explode View...
Page 43 Part List PART (DESCRIPTION) PART (DESCRIPTION) Main Lid indicating light Main lid screw Control knob (thermocouple) Main lid screw cover Control knob Temperature gauge base Main manifold Temperature gauge Main Gas Valve Logo Grease Tray handle Main Lid Handle Heat Insulating Spacer Grease Tray Main Lid Handle base left)
Page 44 Part List Continued PART (DESCRIPTION) PART (DESCRIPTION) smoke canister outer cover right plate right panel back access panel Oven Oven Plate, Rear Rubber Grommet Oven Lamp back panel Oven Flue cart frame rear Oven Grill Inside Liner motor bracket Front Door, left motor Door magnet Spit Fork...
Page 45 Electrical Wiring Diagram LIGHT SWITCH WARNING! ELECTRICAL GROUNDING INSTRUCTIONS: this outdoor cooking gas appliance is equipped with a three-prong (grounding) plug for your protection against shock hazard and should be plugged directly into a properly grounded three- pronged receptacle. DO NOT cut or remove the grounding prong from the plug. Caution: Label all wires prior to disconnection when servicing controls.
Page 46 Ordering Parts IMPORTANT REPLACEMENT PARTS HOW TO ORDER Use only factory authorized parts. The use of To make sure you obtain the correct any part that is not factory authorized can be replacement part(s) for your gas grill, please dangerous. This will also void your warranty. refer to the parts list on this page.
Page 47 Grill Cooking Chart WEIGHT OR APPROXIMATE SPECIAL INSTRUCTIONS AND FOOD THICKNESS HEAT SETTING TIME TIPS VEGETABLES Slice.Dot with butter or margarine Wrap in heavy-duty foil.Grill,turning occasionally Fresh Beets 12 to 20 minutes Carrots Grill,turning once.Brush Occasionally Turnips With melted butter or margarine Onion 1/2 inch slices 8 to 20 minutes...
Page 48 Grill Cooking Chart continued WEIGHT OR APPROXIMATE SPECIAL INSTRUCTIONS HEAT SETTING FOOD THICKNESS FLAME SIZE TIME AND TIPS Tenderloin, Porterhouse, Remove excess fat from edge. Slash T-Bone, Sirloin remaining fat at 2-inch intervals. Rare 1 inch High 8 to 14 minutes Grill, turning once.
Page 49 Grill Cooking Chart continued HEAT FOOD SETTING WEIGHT OR APPROXIMATE SPECIAL INSTRUCTIONS AND THICKNESS TIME TIPS FISH AND SEAFOOD Grill,turning once.Brush with melted butter,margarine or oil To keep moist. Steaks Halibut 3/4 to 1 inch Medium to 8 to 15 minutes Salmon High Swordfish...
Page 50 Grill Recipe Suggestions continued BBQ SALMON TANGY SEAFOOD KABOBS BBQ the chops brushing with the marinade occasionally. Serve with 1 lb. Large shrimp, shelled & 2 large salmon steaks deveined mixed salad, dressed with 2 tbs. Oil vinaigrette flavored with fresh dill. ¾...
Page 51 Grill Recipe Suggestions continued Preheat grill. Combine cheese, Pound flank steak to ¼ inch In blender, process 1/3 c. water, condensed soup, milk, BBQ sauce, thickness or flatten chicken breasts. onion, soy sauce, 2 tsp. oil and the oregano, salt and pepper in a large Mix oil, lime juice and seasonings next 8 ingredients until smooth.
Page 52 Grill Recipe Suggestions continues CHICKEN TANDOORI STYLE Marinade ribs for 3 hours. Use TURKEY marinade for basting by adding 8 large chicken thighs or 12 lb. turkey drumsticks beer to it. Place pan under the ribs and baste frequently. To cook ribs Beer basting sauce: 1 c.
Page 53 Limited Warranty LIMITED WARRANTY MODEL 720-0536 STAINLESS STEEL OUTDOOR GAS GRILL Nexgrill Industries, Inc. warrants to the original consumer purchaser of each Outdoor Gas Grill that when subject to normal residential use, it is free from defects in workmanship and materials for the periods specified below.

This manual is also suitable for:

Gourmet series