Related Manuals for Vivo PP-CW01D
Summary of Contents for Vivo PP-CW01D
- Page 1 Gray Acoustic Ceiling Waffle Panel SKU: PP-CW01D/G Instruction Manual Assembly Video & Product Info www.vivo-us.com/products/pp-cw01g...
- Page 2 If you do not understand these directions, or if you have any doubts about the safety of the installation, please contact our product support team at 309-278-5303 or help@vivo-us.com for further assistance. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual.
-
Page 3: Package Contents
Package Contents A (x2) B (x4) C (x4) XL Panel Large Panel Medium Panel E (x4) D (x4) Cable Small Panel Included Hardware & Tools W-A (x8) W-B (x8) T-A (x1) ST4x41mm Screw Concrete Anchor 2.5mm Allen Wrench Tools Needed: Phillips Drill Drill Bit... -
Page 4: Assembly Steps
ASSEMBLY STEPS STEP 1 Assemble XL Panels (A) by sliding the middle slot in the upper panel into the middle slot of the lower panel as shown. The bottom panel should have the slots facing up, and the upper panel should have the slots facing down. Use caution while sliding the panels together to prevent damage. - Page 5 STEP 2 Sort the remaining panels by size into two groups, with two of each type of panel per group. Group #1 Group #2 Large Panel (B) 2x in Each Group Medium Panel (C) 2x in Each Group Small Panel (D) 2x in Each Group...
- Page 6 STEP 3 Insert each pair of panels from Group #1 into one side of the XL Panel Assembly as shown. XL Panel Assembly...
- Page 7 STEP 4 Insert each pair of panels from Group #2 into the other side of the Panel Assembly as shown. Panel Assembly...
- Page 8 STEP 5 Locate the four holes to install the Cables (E) on the waffle panel. Remove the pre-installed pins on the Panel Brackets (E1) using 2.5mm Allen Wrench (T-A). Use the 2.5mm Allen Wrench to thread the Pins through the Panel Brackets (E1) and the panels.
- Page 9 Option 1: Wood Joist Installation Hold Ceiling Brackets (E2) up to the desired mounting locations and mark drilling locations using a Pencil. Pre-Drilling Instructions Drill mounting holes using illustration below. 1/8” (3mm) Drill Bit 1.6” (40mm) Hole Depth Secure the Ceiling Brackets (E2) to the ceiling using ST4x41mm Screws (W-A) and a Phillips screwdriver.
- Page 10 Option 2: Concrete/Brick Installation Hold Ceiling Brackets (E2) up to the desired mounting locations and mark drilling locations using a Pencil. Pre-Drilling Instructions Drill mounting holes using illustration below. 5/16” (8mm) Drill Bit 1.6” (40mm) Hole Depth Press Concrete Anchors (W-B) into the drilled holes.
- Page 11 STEP 6 Press the spring-loaded barrel on Ceiling Bracket (E2) in and adjust the cable lengths according to your desired height. Hand tighten the nut on Ceiling Brackets (E2).
-
Page 12: Last Updated
LAST UPDATED: 10/3/24 REV1.2 v1.0 Need Help? Get In Touch Monday-Friday from 7:00am-7:00pm CST help@vivo-us.com www.vivo-us.com 309-278-5303 Chat live with an agent! FOR MORE GREAT VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: WWW.VIVO-US.COM VIVO-us @vivo_us...
Need help?
Do you have a question about the PP-CW01D and is the answer not in the manual?
Questions and answers