Advertisement
Advertisement
Table of Contents
Related Manuals for Vivo SIDEKiiX SX-OBT-1C
Summary of Contents for Vivo SIDEKiiX SX-OBT-1C
- Page 1 Under Mattress Desk Instruction Manual SKU: SX-OBT-1C...
- Page 2 [ THIS PAGE INTENTIONALLY LEFT BLANK ]...
- Page 3 If you do not understand these directions, or if you have any doubts about the safety of the installation, please contact our product support team at 309-278-5303 or help@vivo-us.com for further assistance. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual.
-
Page 4: Package Contents
Package Contents B (x1) A (x1) Wrist Pad Tray C (x1) D (x1) Base G (x1) E (x1) F (x2) Pole Height Collar Mounting Bracket Included Hardware & Tools S-A (x3) S-B (x4) T-A (x1) M6x16mm Screw M5x15mm Screw 4mm Allen Wrench Tools Needed: Weight Capacity: 11lbs... -
Page 5: Assembly Steps
ASSEMBLY STEPS STEP 1 Attach the Base (D) to the bottom of the Pole (E) using the M6x16mm Screws (S-A), lining up the three holes on both pieces. Tighten the screws with 4mm Allen Wrench (T-A). ASSEMBLY NOTE Adjustment Handle (E1) should face away from Base (D). -
Page 6: Height Adjustment
STEP 2 Open the Adjustment Handle (E1) on Pole (E) and swing outwards. Slide the Pole up and adjust to your desired height, then close to lock in place. Note: If pole will not slide, turn the Handle counter-clockwise to loosen the joint, then clockwise to tighten. Height Adjustment Open Close... - Page 7 STEP 3 Attach the Mounting Brackets (F) to the underside of the Tray (A) using the M5x15mm Screws (S-B) in the center and the left outer hole set, as shown below. Tighten the screws with a Phillips screwdriver. TRAY ORIENTATION The tray will be assembled to work with either the left or right side of your mattress.
- Page 8 STEP 4 Take note of the sticker on the Arm (C) which indicates the top. Slide Arm (C) into the Mounting Brackets (F), ensuring that the sticker is facing up. Tighten the Knobs on the Brackets (F) to secure the arm in place. THIS SIDE UP ASSEMBLY NOTE Arm is slightly angled up to provide a...
- Page 9 STEP 5 Slide Height Collar (G) onto the top of Pole (E) and secure using 4mm Allen Wrench (T-A), leaving just enough space on the pole for the Arm. Slide the Arm (C) onto the Pole so that it rests on the Collar. Height will be adjusted using Adjustment Handle (E1) in a future step. Remove the protective film of the Wrist Pad (B) and apply it onto the front of the Tray (A), taking note of whether this will be used in a left or right orientation with your mattress.
- Page 10 Adjust As Desired 360° 360° Height Adjustment Open Close To adjust the height, open the Adjustment Handle (E1) on Pole (E) and swing outwards. Slide the Pole to your desired height, then swing the Handle closed to lock in place.
- Page 11 [ THIS PAGE INTENTIONALLY LEFT BLANK ]...
- Page 12 LAST UPDATED: 05/28/24 REV1 v1.0 Need Help? Get In Touch Monday-Friday from 7:00am-7:00pm CST help@sidekiix.com 309-278-5303...
Need help?
Do you have a question about the SIDEKiiX SX-OBT-1C and is the answer not in the manual?
Questions and answers