Listening Through A Receiver (Home Theater); Check Points Before Requesting Service - Samsung HL-T5089S Owner's Instructions Manual

Listening through a Receiver (Home theater)

You can listen to sound through a receiver instead of the TV speaker.
Press the Anynet + button.
1
2 Press the ▲ or ▼ button to select Receiver, press the ◄ or ► button to select to On. Now
you can listen to sound through the receiver.
Press the EXIT button to exit.
When the receiver is set to On, you may listen to the TV sound through the
➢
2-channel(Stereo) Sound. This is not always true. When TV is displaying DTV(air) TV can
send out 5.1 channel sound through SPDIF. But when the source is DVD(for example),
TV can receive only 2 channel sound using HDMI. In that case, 2 channel sound is only
transmitted to the Receiver through SPDIF.
If the receiver is exclusively for a home theater only (supporting audio only), it may not appear in the device list.
➢
Only when you have connected the optical jack of the TV and the receiver properly, does Receiver work.
➢
When Receiver is set to On, a Bluetooth device may not work properly. Or while a Bluetooth device is operating, listening through
➢
the receiver does not work.
In case of a content with copyright problem, listening through the receiver does not properly operate.
➢
When executing WISELINK, the listening through the receiver may not work properly.
➢
When listening through the receiver, there are restrictions for using the PIP and audio-related menu.
➢

Check Points before Requesting Service

Symptom
Anynet + does not work.
I want to start Anynet + .
I want to exit Anynet + .
The Connecting to Anynet+ device
...message appears on the screen.
The Anynet + device does not play.
The connected device is not
displayed.
The TV program cannot be
recorded.
The TV sound is not output through
the receiver.
Solution
Check if the device is an Anynet + device. The Anynet + system supports Anynet + devices
■
only.
■ Connect only one receiver (home theater).
Check if the Anynet + device power cord is properly connected.
■
Check the Anynet + device's Video/Audio/HDMI 1.3 cable connections.
■
■ Check whether the TV remote control is in TV mode.
Check whether it is Anynet + exclusive remote control.
■
Anynet + doesn't work at a certain condition. (Searching channels, operating WISELINK)
■
■ When connecting or removing the HDMI 1.3 cable, please make sure to search devices
again or restart your TV.
Check if the Anynet + Function of Anynet + device is set on.
■
Check if the Anynet + device is properly connected to the TV and check if the Anynet +
■
(HDMI-CEC) is set to On in the Anynet + Setup menu.
Press the TV button on the TV remote control to switch to TV. Then press the Anynet +
■
button to show the Anynet + menu and select a menu you want.
Select View TV in Anynet + menu.
■
■ Press the SOURCE button on the TV remote control and select a device other than
Anynet + devices.
■ Press any of CH, CH LIST, PRE-CH, and FAV.CH to change to the TV mode. (Note that
the channel button operates only when an Anynet + device with a built-in tuner is not
connected.)
You cannot use the remote control when you are configuring Anynet + or switching to a
■
view mode.
Use the remote control when the Anynet + setting or switching to view mode is complete.
■
You cannot use the play function when Plug & Play is in progress.
■ Check whether or not the device supports Anynet+ functions.
■ Check whether or not the HDMI 1.3 cable is properly connected.
■ Check whether <Anynet+ (HDMI-CEC)> is set to <On> in the Anynet+ setup menu.
■ Search Anynet+ devices again.
■ You can connect an Anynet+ device using the HDMI 1.3 cable only. Some HDMI cables
may not support Anynet+ functions.
Check whether the antenna jack on the recording device is properly connected.
Connect the optical cable between TV and the receiver.
English - 84
Device List
Record
Timer Recording
Receiver Off
Headset Connection
Picture Setting
Sound Setting
Sleep Timer Off
▼
Move Enter