SoundPEATS Engine4 Manual

Table of Contents

Contents

1 First Time of Use
2 Pairing of a Second Device
3 Reset
4 Wearing methods
5 Product Diagram
6 Controls
7 Q&A
- 7.1 How to charge the charging case
8 Documents / Resources
- 8.1 Download manual

First Time of Use

Please open the lid of the charging case to take out the headphones, remove the insulating film from the top of both headphones, then put both headphones back into the charging case. Press and hold the button at the bottom of the charging case for 3 seconds until the indicator light inside the charging case flashes white. They are in pairing mode then.
Turn on your device's Bluetooth and select SOUNDPEATS Engine 4 from the Bluetooth list to complete the pairing.

Pairing of a Second Device

SOUNDPEATS Engine earphones can be paired simultaneously with two devices. How to connect: Once the earphones are paired with device A, turn off the Bluetooth of device A Repeat the pairing operation to connect the earphones to device B. When the pairing is completed, please turn on the Bluetooth of device A to complete the pairing.

Reset

Place both earphones back into the charging case, and make sure they are correctly placed.
With the case lid open, press and hold the button on the bottom of the charging case for 10S until the indicator light inside the charging case flashes white twice.
Close the case lid and open it again, and the earphones are activated successfully.

Wearing methods

Identify the left and right earphones.
Adjust the earphones to fit your ears.

Product Diagram

Controls

Power On	Auto: Open the charging case; the earphones turn on automatically Manually: Press and hold the multifunctional button for 15s, with earphones off
Power off	Auto: Place the earphones back into the charging case and close the case lid Manually: Press and hold the multifunctional button for 10s, with earphones on
Play/Pause	Double-tap on the multifunctional button
Volume-	Single-tap on the left multifunctional button
Volume+	Single-tap on the right multifunctional button
Previous Track	Press and hold the left multifunctional button for 1.5s
Next Track	Press and hold the right multifunctiona button for 1.5s
Answer/Hang up a Phone Call	Double-tap on the multifunctional button
Reject a Phone Call	Press and hold the multifunctional button for 1.5s
Switch Between Two Active Calls	Press and hold the multifunctional button tor 1.5s
Activate the Game Mode	Press the left multifunctional button for three times
Activate/Deactivate the Voice Assistant	Press the right multifunctional button for three times

Q&A

What does the indicator light of the charging case display?
1. The battery life of the charging case (When the charging case not in charging mode):

100%-50%	Green
49%-10%	Yellow
<10%	Red

Charging status of the charging case:

<20%	The Red light flashes slowly
20%-69%	The Yellow light flashes slowly
70%-99%	The Green light flashes slowly
100%	The Green light stays on

What does the indicator light on the bottom of the charging case display?
It shows the charging status of the charging case. There are two states of the indicator light while the user is charging the charging case:
1. The red indicator light is always on when the charging case is not fully charged
2. The red light goes out when the charging case is fully charged
How to charge the charging case
1. Connect the charging case to a Type-C charger. (The current does not exceed 1A).
2. If the earphones stay idle for an extended period, charge them at least every three months to prevent the battery from being damaged.
Why are the earphones still connected to the phone when they are put back to the charging case and the case lid is closed?
1. Check whether the charging case has battery power. It it has run out ot battery, closing it will not disconnect the earphones from the device.
2. Ensure the earphones are properly placed in the charging case and the charging metal sheet and PIN are clean. And wiping clean the contact points on the earphones and the charging case should fix this issue.