- Air outlet
- Air purification inlet
- HEPA filter
- Filter cover
- Power cord
- Water tank
- Water tank cover hole
- Water tank float
- Air dehumidification inlet
- Control panel
- Power/purification button
- Dehumidifier button
- Mode button
- Power indicator
- Full tank indicator
BEFORE USE
- Take the product out of the box and remove all packaging material.
- Make sure all parts and components are included and in good conditions. If any visible signs of damage are observed, contact the Technical Support Service immediately.
- Always keep the dehumidifier in an upright position to avoid leakages.
- When installing the device, ensure a minimum safety distance of 30 cm to each of its sides.
HEPA Filter installation/replacement
When the machine detects that the filter needs changing, the LED indicator for the air purifier will continuously flash in orange.
![cecotec - BigDry 2500 Pure Light - HEPA Filter installation/replacement HEPA Filter installation/replacement]()
- Pull and lift to open the filter cover (4).
- Pull out to extract the filter.
- Remove the packaging of the new filter.
- Insert the new filter into the machine.
- Clip the filter cover back into the machine. To do so, align the bottom of the filter cover with the body of the device and push the cover towards the device.
Note: After replacing the filter, turn the appliance on and press and hold the power/purification (11) button for seven seconds to reset it.
OPERATION
When the machine is connected to the power, the power indicator will turn on.
- Press the power/purification button (11), the purification indicator will turn on and the appliance will begin to work in air purification mode.
- Press the power/purification button (11) again and the appliance will turn off.
- Press the dehumidifier button (12) when the machine is turned on and the machine will dehumidify with the purification function.
- Press the dehumidifier button (12) again to switch off the dehumidification function off. The purification function will continue operating. The LED indicators will light up accordingly.
- Press the mode button (13) to set the intensity of purification once it's activated.
- This button has two modes, a high intensity or a low intensity.
CLEANING AND MAINTENANCE
Draining collected water
- The water tank has a maximum capacity of 1000ml with a 750 ml/ per day working capability.
- When the water tank is full, the full tank LED indicator will light up.
- Switch off and unplug the machine.
- Avoid tilting it and carefully remove it, slide the water tank cover open and pour the water out.
- Insert the water tank cover and then insert the water tank back into the unit and press the power/purification button (11) to resume operation.
![]()
- Do not damage or remove the water tank float as this can affect the operation of the appliance, cause water leaks and malfunction.
Cleaning and storing the device
- Make sure the unit is powered off and that the power cable is disconnected from the power source.
- Use a soft cloth to clean away any dust or debris from the surface of the unit or the air inlets.
- Pull out the water tank and slide out the cover to clean the water tank.
- Do not clean the filter with a vacuum cleaner or wash it directly, just put the filter under the sun to sterilize it regularly.
TROUBLESHOOTING
Problem | Reason |
Appliance not working | - Is it plugged into a power socket?
- Is the power outlet or fuse in good condition?
- Is the water tank full?
|
| - Is the filter blocked?
- Is the door of the room open?
- Are there any obstacles blocking the air inlet/outlet?
- Is there other equipment releasing steam indoors?
- Is the indoor temperature too low?
|
The air volume becomes smaller | - Is the filter too dirty to let the air go through?
- Is the air inlet/outlet of the machine blocked by something?
|
Significant noise | - Is there anything stuck on the fan or near the air outlet?
- Is the machine tilted?
|
Leakage | - Is the machine tilted?
- Is there any water left in the tank?
- Is the float device in the water tank in good condition?
|
Note: If the above troubleshooting FAQ does not solve your problem and you require maintenance, do not hesitate to contact Cecotec Technical Support Service at +34 963 210 728.
TECHNICAL SPECIFICATIONS
Model: BigDry 2500 PureLight - BigDry 2500 PureLight Black
Reference: 05604 - 05605
Power output: 45 W
Voltage: 100 - 240 V 50/60 Hz
Working capacity: 750 ml/day
TECHNICAL SUPPORT SERVICE AND WARRANTY
This product is under warranty for 2 years from the date of purchase, as long as the proof of purchase is submitted, the product is in perfect physical condition, and it has been given proper use, as explained in this instruction manual.
The warranty service covers every manufacturing defects of your appliance for 2 years, based on current legislation, except consumable parts. In the event of misuse, the warranty will not apply.
If at any moment you detect any problem with your product or have any doubt, do not hesitate to contact Cecotec Technical Support Service at +34 96 321 07 28.
Read these instructions thoroughly before using the appliance. Keep this instruction manual for future reference or new users.
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Need help?
Do you have a question about the BigDry 2500 Pure Light and is the answer not in the manual?
Questions and answers