Xiaomi 4 Lite - Electric Scooter Manual

Package Contents

Accessories

Note: Illustrations of product, accessories, and user interface in the user manual are for reference purposes only. Actual product and functions may vary due to product enhancements.

Product Overview

1. Accelerator
2. Control Panel & Power Button
3. Buckle
4. Deck
5. Hook
6. Taillight

7. Rear Mudguard
8. Wheel Motor
9. Battery Compartment
10. Kickstand
11. Handlebar
12. Headlight

13. Scooter Bell
14. Brake Lever
15. Stem

16. Quick Release Lever
17. Quick Release Lever Lock
18. Front Fork

19. Front Wheel
20. Mechanical Brake
21. Winglight

Control Panel & Power Button

1. Temperature Warning: If the battery temperature is too high or too low, the thermometer icon will be on. This will result in 1 reduced acceleration and possibly charging issues. Use or charge the scooter a er its battery temperature returns to the normal operating range.
2. Power Button: Press the Button to turn the scooter on, and hold the Button for 2 to 3 seconds to turn the scooter off. When the scooter is on, press the Button to turn on/off the headlight and taillight, and press twice to cycle through the riding modes.
3. Battery Level: The battery power is indicated by 5 bars, each representing approximately 20% of a full battery.
4. Error Notification: When the wrench icon displays red, it indicates that the scooter has an error.
5. Bluetooth: When the scooter is successfully connected to a mobile device, the Bluetooth icon will light up, and the maximum speed will be unlocked.
6. Winglight: Press the left or right winglight button, then the corresponding winglight and the indicator on the control panel will blink. Press the same button again, and the corresponding winglight and the indicator will turn off.
7. Lock: The lock icon will remain on when the scooter is locked and go out when the scooter is unlocked.
8. Speedometer: It displays the current speed when the scooter is working. When the scooter has an issue, it displays an error code. When the scooter is charging, it displays the current battery level.
9. Riding Mode: is for walking mode, and its maximum speed is about 6 km/h; the taillight will blink when this mode is enabled. D is for standard mode, and its maximum speed is about 15 km/h. S is for sport mode, and its maximum speed is about 20 km/h. The scooter has high speed in S mode, and it is recommended to use it after mastering the riding skills.

Assembly and Set-up

1. Put down the kickstand, and hold up the stem until it is completely in an upright position. Then li the quick release lever lock, and push the quick release lever inward to the end.
   

2. Insert the handlebar onto the stem. Make sure to install the handlebar facing the correct direction.
   

3. Follow the number order as illustrated to pre-tighten the six screws with the included Allen key. Make sure the handlebar is correctly installed and then tighten the screws thoroughly.
   

Charge Your Scooter

The scooter is fully charged when the LED on the battery charger changes from red (charging) to green (fully charged).
Notes:

• Do not charge the scooter if the charging port, power adapter, or power outlet is wet.
• When the scooter is not being charged or after the charging is complete, make sure the rubber flap is inserted tightly into the charging port to prevent water from getting in.

2. Scan the QR code on the label a ached to the control panel, on the right side of the deck, or on the back cover of the user manual to download the Mi Home/Xiaomi Home app.
   

3. Open the Mi Home/Xiaomi Home app.
   

4. Tap "+" on the top right corner and open "Scan" to scan the QR code on the label a ached to the control panel, on the right side of the deck, or on the back cover of the user manual again. Then follow the instructions in the app to add the scooter.
   

Notes:

• Open the Mi Home/Xiaomi Home app to use various functions, such as one-tap locking, energy recovery, and one-tap turning-on of the taillight.
• The version of the app might have been updated, please follow the instructions based on the current app version.

Bluetooth resetting
Make sure the scooter is turned on. Press and hold the accelerator to the end, and simultaneously press the power button on the control panel 5 times in succession. When the Bluetooth is successfully reset, the scooter will make a buzz and the Bluetooth icon will blink.

Restore factory settings
Make sure the scooter is turned on. Squeeze the brake lever, and simultaneously press and hold the accelerator and the power button for 7 seconds. When you hear a buzz, the scooter's Bluetooth has been unpaired and the scooter has been restored to factory settings. Then the control panel will return to its factory display and the Bluetooth icon will blink.
Note: The scooter cannot be restored to factory settings during riding or when locked.

How to Ride

1. Wear a helmet, elbow pads and knee pads before riding
   Note: Check the tire pressure before riding. The recommended tire pressure is 45–50 psi.
   

2. Step on the deck with one foot, and slowly kicks off the other on the ground.
   

3. When the scooter starts to coast, put both feet on the deck and gently press the accelerator. The accelerator can be used once the scooter is going over 5 km/h.
   

4. Gently press the accelerator to speed up and make sure not to go too fast.
   

5. Slowly release the accelerator or press the brake lever to slow down.
   Pay attention to the road conditions when riding and make sure to maintain an appropriate speed without sudden braking. Otherwise, the tires may lose grip and cause you to fall, resulting in serious injury.
   

6. Tilt your body to the steering direction as you turn, and slowly turn the handlebar.
   

7. When the scooter slows down or stops, put one foot on the ground to get off the scooter.
   

8. Put down the kickstand when parking the scooter.
   To avoid others using the scooter without your permission, you can lock the scooter when it is parked.
   

Lock/Unlock Your Scooter

Tap to lock

Tap to Unlock

When the scooter is locked, the motor is locked and all the icons on the control panel will automatically go out except the Bluetooth icon and the lock icon. If the scooter goes beyond the Bluetooth connection range, the Bluetooth will be disconnected and its icon will go out.
If the scooter is locked, the motor will be locked. When you push the scooter forward, it will have a rolling resistance accompanied by the buzzer alarm. The scooter will automatically turn off after 24 hours of being locked, and remain locked when turned on again. You need to unlock the scooter via the Mi Home/Xiaomi Home app. Locking the scooter will consume the scooter's power, please use this function properly.

Fold/Unfold & Carry

Folding

1. Make sure the scooter is turned off and not being charged before folding. Hold the stem, lift the quick release lever lock, and pull the quick release lever outward.
   
2. Lift the quick release lever lock again, and pull the quick release lever outwards to pop the bottom folding hook out. Then fold the stem.
   

3. Align the buckle with the hook and secure them together.
   

Carrying

Hold the stem with either one hand or both hands to carry.

Unfolding

1. When unfolding the scooter, pull the buckle upwards to release it from the hook.
   

Inflate the Tire

1. Connect the pump to the extension nozzle.
   

2. Remove the tire valve cap, and connect the extension nozzle and the valve securely together.
   

3. Inflate the tire.
   

4. Tighten the tire valve cap securely a er inflating the tires.
   

Notes:

• Check the tire pressure every month, and inflate the tires if the pressure is too low. The recommended tire pressure is 45–50 psi.
• Removing tires is complex and should be operated by a professional, and incorrect operation could lead to instability of the scooter or other issues.

Adjust the Mechanical Brake

Before adjustment, make sure the scooter is powered off and not charging.
Tool: 14 mm T-handle socket wrench (the tool needs to be prepared by the user).
When the brake is too tight, use the tool to turn the nut on the screw rod counterclockwise, so as to slightly shorten the brake cable's exposed bottom part. When the brake is too loose, use the tool to turn the nut on the screw rod clockwise, so as to slightly lengthen the brake cable's exposed bottom part.

Safety Reminder

Battery and Charging Precautions

• Do not charge if the charging port, power adapter, or power outlet is wet. Read the user manual carefully before charging.
• Before charging, turn off the scooter or make sure it is not running.
• Do not use any third-party battery or power adapter.
• Charge at a temperature between 0°C and 45°C. Failure to properly charge the scooter within the specified temperature range could damage the battery.
• Do not dismantle, repair, or modify the battery on your own, as it contains hazardous substances.
• If you are not planning to use the scooter for an extended period, turn it off, fully charge it, and store it in a cool, dry place. To prevent damage from over-discharging, charge your scooter at least once every two months.

Do not Try Dangerous Actions
Wear a helmet, elbow pads and knee pads before riding.

Do not ride with anyone else, including children.

Do not hang bags or other heavy stuff on the handlebar.

Unless otherwise authorized by the local laws, it is forbidden and illegal to ride on public roads, motorways, and expressways.

Do not ride the scooter with one or both hands off the handlebar, or with only one foot.

Do not use mobile phone or wear earphones when operating the scooter.

When riding on uneven roads or in other poor road conditions, make sure to slow down as you ride over it or get off and walk with the scooter. To reduce the risk of accidents, ride your scooter on smooth surfaces that are free of potholes.

Avoid hi ing your head on door frames, elevators, and other overhead obstacles.

Do not ride in the rain. Do not ride through puddles or any other (water) obstacles.

Do not exceed the scooter's specified maximum payload (100 kg).

Do not touch the mechanical brake.

Do not accelerate when going downhill, and brake in time to slow down. When on a steep slope, you need to step off the scooter and push.

Do not drink and drive. Riding a scooter while under the influence of alcohol or other substances is strictly prohibited.

Do not keep your feet on the rear mudguard.

Do not try riding up or down stairs, nor try jumping over obstacles.

Do not press the accelerator when you are walking alongside the scooter.