BLACKSTONE 2177 - 36" GRIDDLE Manual

BLACKSTONE 2177 - 36" GRIDDLE Manual

Advertisement

BLACKSTONE 2177 - 36" GRIDDLE Manual

IMPORTANT SAFETY INFORMATION


Indicates a hazardous situation that, if not avoided, will result in death or serious injury


Indicates a hazardous situation that, if not avoided, could result in minor or moderate injury


Indicates a hazardous situation that, if not avoided, could result in death or serious injury

information NOTICE Indicates information considered important, but not hazardrelated (eg. messages related to property damage)

If you smell gas:

  • Shut off gas to the appliance.
  • extinguish any open flame.
  • If odor continues, keep away from the appliance and immediately call your gas supplier or your fire department.

Failure to follow these instructions could result in fire or property damage, personal injury or death.

  • DO NOT store or use gasoline or other flammable liquids or vapors in the vicinity of this or any other appliance.
  • An LPG cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.

GAS APPLIANCE SAFETY

  • The use of alcohol, prescription, or non-prescription drugs may impair the consumer's ability to properly assemble or safely operate the appliance
  • Keep children and pets away from the appliance at all times
  • Have a type BC or ABC fire extinguisher readily available
  • NEVER operate this appliance unattended.
  • NEVER operate this appliance within 10 ft (3.0 m) of any structure, combustible material or other gas cylinder.
  • NEVER operate this appliance within 25 ft (7.5 m) of any flammable liquid.
  • If a fire should occur, keep away from the appliance and immediately call your fire department. DO NOT attempt to extinguish an oil or a grease fire with water.
Failure to follow these instructions could result in fire or property damage, personal injury or death.

DO NOT USE FOR PURPOSES OTHER THAN INTENDED:

  • DO NOT use for commercial cooking
  • DO NOT use this appliance as a heater

THIS APPLIANCE SHALL BE USED OUTDOORS ONLY.

  • DO NOT use this appliance inside buildings, garages, or any other enclosed area
  • DO NOT install this appliance in or on a boat
  • DO NOT install this appliance in or on a recreational vehicle

MAINTAIN PROPER CLEARANCES FROM COMBUSTIBLE MATERIAL:

  • DO NOT use this appliance on or under any apartment or condo-minium balcony or deck
  • DO NOT use this appliance under overhead combustible construction
  • DO NOT obstruct the flow of combustion and ventilation air
  • DO NOT operate this appliance any closer than 36 in (1 m) from the sides and back of the appliance

INSTALLATION MUST CONFORM WITH LOCAL CODES
In the absence of local codes, installation must conform with:

  1. National Fuel Gas Code, ANSI Z2231/NFPA 54, Storage and Handling of Liquefied Petroleum Gases, ANSI/NFPA 58; or
  2. Natural Gas and Propane Installation Code, CSA B1491; Propane Storage and Handling, CSA B1492; or
  3. TheStandard for Recreational Vehicles, ANSI A1192/NFPA 1192; and

Recreational Vehicle Code, CSA Z240 RV Series, as applicable

Improper installation, use, adjustment, alteration, service, modification, or maintenance can cause injury or property damage. Refer to this manual.

ASSEMBLY GUIDE

EXPLODED VIEW

EXPLODED VIEW

PARTS LIST

PARTS QTY PARTS QTY PARTS QTY PARTS QTY
1.1a Control panel 1 1.3a left leg assembly 1 1.5a Heat shield 1 1.9 Regulator 1
1.1b Background panel 1 1.3b Right leg assembly 1 1.5b Thermal baffle 1 7.1 Magnetic strip 1
1.1c Control knob bezels 4 1.3c Paper towel bracket 1 1.6 Ignition needles 4
1.2a left front U sheet 1 1.4a Ignitor 1 1.7 Tubular burners 4
1.2b Right front U sheet 1 1.4b Ignitor button 1 1.8 Gas rail & Valves 1

PARTS LIST

19 Hardware pack (1 piece)

  1. Shelf pegs (8 pieces)
  2. M4x10 screws (4 pieces)
  3. M6x12 screws (13 pieces)
  4. M6 step bolts (8 pieces)
  5. Small thumb screws (2 pieces)
  6. Shelf peg washers (8 pieces)
  7. Large thumb screw (1 piece)
  8. Medium thumb screw (1 piece)
  9. Shear pin (1 piece)
  10. Cotter pin (1 piece)
  11. Washers (2 pieces)
  12. Acorn nuts (2 pieces)
  13. Lock washers (2 pieces)

Find a large, clean area to assemble your appliance

Remove all packing material before assembling


Sharp edges. Wear gloves while assembling.


Heavy pieces. Two people should assemble this appliance.

NOT INCLUDED:

LPG cylinder
Size: 18 x 12 in (45 x 30 cm), 20 lb (9 kg)
PG cylinder must include collar to protect LPG cylinder valve.

NOT INCLUDED:

AA battery

TOOLS NEEDED:

Phillips head screwdriver & Adjustable wrench

STEP 01 With the help of another person, remove the griddle body from the packaging and lay it upside down on a smooth, flat surface
Unlatch and unfold the legs to their vertical position

  1. Use two (2) small thumb screws [e.] to attach the fixed wheels onto the ends of the right leg assembly
  2. Use two (2) acorn nuts [l.] and two (2) lock washers [m.] to attach the two (2) caster wheels onto the left leg assembly (ensure that the caster wheels are locked)
    ASSEMBLY GUIDE - Step 1

STEP 02 Place the bottom shelf between the leg assemblies

  1. Use one (1) large thumb screw [g.] to secure the shelf to the left leg assembly
  2. Use one (1) medium thumb screw [h.] to attach the LPG support and secure the shelf to the right leg assembly
    ASSEMBLY GUIDE - Step 2

STEP 03 With the help of another person, set the griddle body on its feet.
Use one (1) shear pin [i.] and one (1) cotter pin [j.] to attach the propane tank hanger to the upper bar of the left leg assembly.
ASSEMBLY GUIDE - Step 3

STEP 04 Use one (1) M6x12 screw [c.] and two (2) washers [k.] to attach the paper towel holder to the paper towel bracket
ASSEMBLY GUIDE - Step 4

STEP 05 Install the four (4) control knobs by pushing them into place in the oFF position
ASSEMBLY GUIDE - Step 5

STEP 06 Use four (4) M6x12 screws [c.] to install the side handle to the left side of the griddle body
ASSEMBLY GUIDE - Step 6

STEP 07 Use four (4) M6x12 screws [c.] to attach one (1) side shelf bracket (l), and one (1) side shelf bracket (R) to the right side of the griddle body Repeat this step with the left side of the griddle body
ASSEMBLY GUIDE - Step 7

STEP 08 Thread four (4) side shelf pegs [a.] through four (4) peg washers [f.] and into the right side shelf
Repeat with the left side shelf
ASSEMBLY GUIDE - Step 8

STEP 09 Thread two (2) M6 step bolts [d.] into the upper holes of the right side shelf Repeat with the left side shelf
ASSEMBLY GUIDE - Step 9

STEP 10

  1. Slide the right side shelf onto the side shelf brackets (The threaded M6 step bolts will hook and hold the shelf)
  2. Use two (2) M6 step bolts [d.] to secure the right side shelf to the side shelf brackets. Repeat with the left side shelf.
    ASSEMBLY GUIDE - Step 10

STEP 11 Hang the grease cup in the slot on the back of the griddle body

STEP 12 With the help of another person, place the griddle top onto the griddle body by aligning the four foot pins to the holes on top of the unit
ASSEMBLY GUIDE - Step 11
Make sure the front pins are fully seated in the holes, then push the griddle top back to lock the griddle in place.

STEP 13 Use four (4) M4x10 screws [b.] to attach the two (2) hard cover handles and two (2) hard cover hooks to the hard cover
ASSEMBLY GUIDE - Step 12
(Hang hard cover on back of griddle top when in use, and place hard cover on the griddle top when not in use)
ASSEMBLY GUIDE - Step 13

STEP 14 Proceed to USING YOUR BLACKSTONE
ASSEMBLY GUIDE - Step 14

Handle will get hot while appliance is in use.
DO NOT touch the handle while appliance is hot.
information NOTICE
  • Maximum weight on the side shelf is 10 lbs (4.5 kg).
  • The side shelf may get hot while appliance is in use.

USING YOUR BLACKSTONE

THE LPG CYLINDER VALVE MUST HAVE:

  • Type 1 valve outlet (thread on the outside)
  • Safety relief valve
  • Ul listed overfill Protection device (OPD) This OPD safety feature is identified by a unique triangular hand wheel
  • Safety cap (dust cap)

LPG CYLINDER REQUIREMENTS

  • The LPG supply cylinder to be used must be constructed and marked in accordance with the specifications for lP gas cylinders, US department of Transportation (doT) or the Standard for Cylinders, Spheres and Tubes for the Transportation of dangerous Goods, CAN/CSA-B339
  • only LPG cylinders marked "propane" shall be usedThe LPG cylinder supply system must be arranged for vapor withdrawal
  • Always keep new LPG cylinders in upright position during use, transit or storage.
  • Always keep the ventilation opening(s) of the cylinder enclosure free and clear from debris.

REGULATOR SAFETY

Cross threading can occur if you force thread a connection at an improper angle. This will damage the threads, lead to propane leaking, and potentially result in a build-up of fuel that can ignite.
DO NOT cross thread the connection between your LPG cylinder and regulator.
If you can not connect the regulator, DO NOT use the regulator.
Regulator must be replaced with a Blackstone approved model by a professionally licensed, authorized dealer.

Use this appliance, as purchased, only with gas and regulator/valve assembly supplied

FITTINGS & HOSES

  • Annual checking and tightening of metal fittings is recommended
  • Keep the fuel supply hose away from any heated surfaces
  • Before each use, check to see if hoses are cut or worn

Replace damaged hose before using appliance. (Use only Blackstone approved replacement parts for valve, hose, or regulator. Failure to comply will void the warranty.)

CONNECT THE LPG CYLINDER

20 LB (9 KG)

STEP 01 Turn the control knobs to oFF

  1. Ensure that the LPG cylinder is oFF by turning the OPD hand wheel clockwise to a full stop
  2. Remove the safety cap from the Type 1 valve outlet

STEP 02 Hold the regulator in a straight line with the Type 1 valve outlet so as not to cross thread the connection Center and insert the regulator nipple into the Type 1 valve outlet

Hand-tighten the coupling nut in a clockwise direction (DO NOT use tools to connect)

If connection cannot be completed, disconnect regulator and repeat this step.

STEP 03 Secure the LPG cylinder to the appliance by hanging it on the LPG hook so that it nestles against the LPG support

LEAK TEST INSTRUCTIONS

information NOTICE
DO NOT use household cleaning agents. Damage to gas valve, hose, and regulator components may result.
Use a clean paintbrush and a 10/90 mild soap and water solution to perform the leak test.

LEAK TEST: LPG CYLINDER

  • Leak test new and exchanged LPG cylinders BeFoRe connecting to griddle
  • DO NOT smoke during leak test
  • DO NOT use an open flame to check for gas leaks
  • Appliance must be leak tested outdoors in a well-ventilated area, away from ignition sources such as gas fired or electrical appliances
  • During leak test, keep appliance away from open flames or sparks

STEP 01 Brush soapy solution onto joint areas of the LPG cylinder (Indicated by arrows in figure 01.)

  • Leaks are indicated by growing bubbles
If growing bubbles appear during leak test, DO NOT use or move the LPG cylinder. Immediately contact an LPG supplier or fire department.

LEAK TEST: VALVES, HOSE & REGULATOR

STEP 01 Turn the control knobs to oFF

STEP 02 Connect the regulator to the LPG cylinder

STEP 03 Completely open the LPG tank by turning the OPD hand wheel counterclockwise

  • If you hear a rushing sound, turn gas off immediately There is a major leak at the connection
  • Immediately close the LPG cylinder by turning the OPD hand wheel clockwise and re-tighten connections If leaks cannot be stopped. DO NOT try to repair

STEP 04 Brush soapy solution onto joint areas of valves and regulator (Indicated by arrows in figure 02.)

  • leaks are indicated by growing bubbles
  • Immediately close the LPG cylinder by turning the OPD hand wheel clockwise and re-tighten connections
If leaks cannot be stopped, DO NOT try to repair.
Regulator must be replaced with a Blackstone approved model by a professionally licensed, authorized dealer.

FIRST TIME CLEANING

CLEANING YOUR GRIDDLE TOP

information NOTICE
Soap will ruin a seasoned griddle. This is the only time you should use soap on the griddle cooking surface.

STEP 01 Wash the griddle cooking surface with hot, soapy water

STEP 02 Rinse and dry completely

IGNITION INSTRUCTIONS

CHECK VALVES

STEP 01 Turn knob to oFF position

STEP 02 Push in knob and release Knob should spring back
If knobs DO NOT spring back, replace valve assembly before using appliance.

STEP 03 Rotate knob to loW then turn back to oFF Knob should turn smoothly

If burner does not ignite with open LPG cylinder valve, gas will continue to flow out of burner and could accidentally/ inadvertently ignite with risk of injury.
Ensure gas is off at the supply shut off valve before checking appliance valves.

BATTERY POWERED IGNITION

warning DO NOT lean over the appliance while lighting

STEP 01 Insert one (1) AA battery (not included) under the ignitor button

Screw the button into place over the positive terminal

STEP 02


  1. Turn the control knob to oFF

    Turn gas oN at the LPG cylinder by turning the OPD hand wheel counterclockwise 1 to 3 turns

STEP 03

  1. Push and hold the ignitor button
  2. Push and turn the control knob counter-clockwise to HIGH (Release the ignitor button when the burner lights)
  3. Adjust the temperature to desired level

CHECK BURNER FLAME

Always check burner flame before use

STEP 01 light burners and rotate knobs from HIGH to loW

STEP 02 look below the cooking top to view burners. When knob is at HIGH, flames should be larger than when knob is at loW.

A clogged burner can lead to a fire beneath the appliance.
Burner should be removed and cleaned annually or whenever heavy build-up or insects/insect nests are found.

HEALTHY BURNER FLAME PATTERN

  1. Flickers of yellow color
  2. Ddark blue color
  3. Vibrant blue

BURNER FLAMES ARE YELLOW OR IRREGULAR

If there is a sudden drop or low flame issue, please reference the Troubleshooting chapter

GRIDDLE SEASONING INSTRUCTIONS

WHAT OIL IS BEST TO USE?

  • Blackstone Seasoning and Cast Iron Conditioner.
  • Any plant-based cooking oil.
  • Rendered animal fat with no additives.

VIDEO TUTORIAL
How to Season a New Blackstone Griddle youtube.com/watch?v=VspmdVnj2pI&t=3s

STEP 01 Wipe any debris off griddle top.

STEP 02 Set your griddle to high heat until your griddle top changes color. (~10 min)

STEP 03 Use tongs to hold a paper towel or cotton cloth and spread 2-3 tablespoons of your seasoning oil across the entire griddle top.

When seasoning your griddle top, remember to use a thin and even layer of oil—the thinner the layer of oil, the easier it will be to burn it off

STEP 04 The griddle top is ready for another layer of oil when it stops smoking. Repeat STEP 03 3-4 times, or until the griddle surface is black.

PREVENTING RUST

Use your griddle frequently. every time you cook, you are adding to the seasoning, which makes rust less likely.

information NOTICE
If you live in a humid or coastal climate, your griddle may require more frequent seasonings between uses.

If rust appears on the griddle surface, rub it off with steel wool, low grit sandpaper or the Blackstone Pumice Stone and re-season the surface.

VIDEO TUTORIAL
Recovering your Blackstone Griddle Top
youtube.com/watch?v=thPe2IgnSiI

COOKING ON YOUR BLACKSTONE

Flammable items can spontaneously combust if placed near the appliance. DO NOT place flammable items such as aerosol containers, oily or greasy towels near the cooking surface.
This appliance will be hot during and after use. DO NOT handle hot parts with unprotected hands. Use long-handled cooking utensils and oven mitts.
information NOTICE
DO NOT store any items within 3 in (8 cm) of the cooking surface while in use.

IF GREASE OR OTHER HOT MATERIAL DRIPS ONTO VALVE, HOSE OR REGULATOR:

STEP 01 Turn off gas supply immediately.

STEP 02 Determine the cause and correct it.

STEP 03 Clean and inspect valve, hose and regulator. STEP 04 Perform a leak test. (Please reference the leak Test Instructions in USING YOUR BLACKSTONE.)

VIDEO RECIPES
Find recipes and cooking tips at:
blackstoneproducts.com/blogs/recipes
youtube.com/c/BlackstoneGriddles
@blackstoneproducts

CLEANING YOUR APPLIANCE

Clean your appliance after each use, after it is cool to the touch.

  • DO NOT use abrasive pad on areas with graphics.
  • If a bristle brush is used to clean any of the cooking surfaces, ensure no loose bristles remain on cooking surfaces prior to cooking.
Grease build up can cause a fire. Clean any part of the appliance that gets hot and experiences grease build up after each use.

PLASTIC PARTS & PAINTED SURFACES:
Wash with warm soapy water and wipe dry with a non-abrasive cloth.

information NOTICE
DO NOT use Citrisol, abrasive cleaners, or a concentrated cleaner on plastic parts. This may result in damage to and failure of parts.

APPLIANCE STORAGE


DO NOT move the appliance when in use. Allow the appliance to cool to 115°F (45°C) before moving or storing.

COVER FIT GUIDE
Always cover your appliance if stored outdoors.

Visit blackstoneproducts.com/support to find a cover that will fit your appliance.

CLEANING YOUR GRIDDLE TOP

Clean griddle top after each use, while still warm.

  • DO NOT use soap on the griddle top. This will destroy the griddle's seasoning.
  • The grease cup must be removed and emptied after each use.
Grease cup will be hot during and after use. DO NOT remove the grease cup until the griddle has completely cooled.

VIDEO TUTORIAL
How to Clean your Blackstone Griddle
youtube.com/watch?v=-Iedu9z6NPY

STEP 01 Push loose food debris into the grease cup with spatula or straight metal scraper.

STEP 02 Wipe down griddle top with paper towel.

STEP 03 Apply a few tablespoons of water to the griddle surface, then scrape the water and debris into the grease cup. (For stuck-on food residue, use a bit of coarse salt.)

STEP 04 Wipe again with a paper towel and dry completely.

STEP 05 Apply thin coat of cooking oil to maintain seasoning and protect the griddle top.

DISCONNECT THE LPG CYLINDER

20 LB (9 KG)

STEP 01

  1. Ensure that the control knobs are turned to oFF by turning the OPD hand wheel clockwise to a full stop.
  2. Turn the coupling nut counter-clockwise by hand to remove the regulator. (DO NOT use tools to disconnect.)

STEP 02 Place safety cap on LPG cylinder valve outlet whenever cylinder is not in use.
Only install the type of safety cap on cylinder valve outlet that is provided with the cylinder valve other types of caps or plugs may result in leakage of propane

STORING LPG CYLINDERS

  • DO NOT store a spare LPG cylinder under or near this appliance.
  • DO NOT fill an LPG cylinder beyond 80% full.

If the information above is not followed exactly, a fire causing death or serious injury may occur

  • The LPG cylinder must be turned oFF when the appliance is not in use
  • LPG cylinders must be stored outdoors and out of the reach of children
  • DO NOT store an LPG cylinder inside a building, garage, or any other enclosed area

FILLING & EXCHANGE

  • Use only those reputable exchange companies that inspect, preci-sion fill, test and certify their cylinders. LPG dealer must purge new cylinder before filling.
  • Volume of propane in cylinder will vary by temperature.
A frosty regulator indicates gas overfill.
Immediately close LPG cylinder valve and call local LPG dealer for assistance.
  • DO NOT release liquid petroleum gas (LPG) into the atmosphere.
  • To remove gas from LPG cylinder, contact a certified LPG dealer or local fire department for assistance.
  • Exchange tank only for an OPD safety feature-equipped tank.

Your retailer can help you match a replacement LPG cylinder to your appliance

TROUBLESHOOTING

IGNITION TROUBLESHOOTING

BURNER WILL NOT IGNITE:
If ignition does not occur in 5 seconds:

STEP 01 Turn the burner controls OFF.

STEP 02 Wait 5 minutes.

STEP 03 Repeat the lighting procedure.
If this does not work, to determine the cause, please try to ignite your appliance with a match

MATCH LIGHTING INSTRUCTIONS
Before beginning, check for gas leaks. (Please reference the leak Test Instructions in USING YOUR BLACKSTONE.)

STEP 01 Turn control knob(s) to OFF position.

STEP 02 Light a match (or long lighter) no shorter than 11 inches long.

STEP 03 Place the flame on the right or left side of the burner.

STEP 04 Push in and turn the control knob to the HIGH position. ensure burner lights and stays lit.

IF YOU CAN IGNITE YOUR APPLIANCE WITH A MATCH:

POSSIBLE CAUSES SOLUTION
Dead/Improperly installed battery Replace with new battery
Ignitor wire misaligned. Ensure that the ignition needle is positioned 3-7mm away from the burner tube, and above a burner hole.
Damage to the ignition system. Contact customer service for replacement parts.

IF YOU CAN NOT IGNITE YOUR APPLIANCE WITH A MATCH:

POSSIBLE CAUSES SOLUTION
Burner tubes are not receiving fuel. Clean the burner assembly to remove the obstruction.

GAS FLOW TROUBLESHOOTING

BURNER FLAMES ARE YELLOW OR IRREGULAR:

  • Appliance will not achieve a high heat or heats unevenly.
  • Burner flames start strong, then immediately drop to low even when burner is set to high position.
  • Flame height drops when a second burner is lit.
  • Flames DO NOT extend the full length of the burner, or only run on one side of the burner.
  • Burner flames are inconsistent.
POSSIBLE CAUSES SOLUTION
Obstructions in the burner, gas jets, or fuel rail. Clean the burner, jets, and gas hose.
LPG cylinder is empty or low. Refill or replace the LPG cylinder.
The regulator's flow limiting device was triggered.

Reset the safety system:
STEP 01 Turn oFF the appliance, close the LPG cylinder valve, and disconnect the regulator from the LPG cylinder.

STEP 02 Wait five minutes to allow the pressure to dissipate, then reconnect the regulator to the LPG cylinder and slowly open the OPd hand wheel one half turn.

STEP 03 Ignite your appliance.

Regulator stuck in safety position. Contact customer service for replacement parts.

A FLAME IS COMING OUT OF THE AIR GATE:

POSSIBLE CAUSES SOLUTION
Something is blocking the venturi in the burner tube. Clean the burner assembly to remove the obstruction.

SEASONING TROUBLESHOOTING

THERE IS A BROWNISH RESIDUE ON THE GRIDDLE SURFACE:

POSSIBLE CAUSES SOLUTION
  • Too much oil was used.
  • You turned off the heat too soon.

STEP 01 Turn your griddle on high and let it heat for 10-15 minutes.

STEP 02 Scrape off as much of the thickened and partially cooked oil as you can.

STEP 03 Re-season with a very thin layer of oil.

THE EDGES OF THE GRIDDLE SURFACE ARE NOT BLACK:
After using your griddle for multiple cooks, the seasoning will even out and improve.

CLEANING THE BURNER ASSEMBLY

VIDEO TUTORIAL
How to Clean Your Burner Tube
youtube.com/watch?v=xKQTCrFCzf8

STEP 01 Ensure that the gas is turned OFF at control knobs and gas supply. Remove the cooking top.

STEP 02 Carefully detach and remove the burner.

STEP 03 Clean the inside of the burner:

  • Run a narrow bottle brush through each burner tube several times. (DO NOT use wire brushes)
  • Run a stiff wire bent into a small hook through each burner tube several times.
  • Use an air hose to force air into burner tube and out burner ports. Check that air blows through each hole. (Wear eye protection)

STEP 04 Brush entire outer surface of burner to remove grime.

STEP 05 Clean any blocked ports with stiff wire such as an open paper clip.

STEP 06 Carefully replace burners and reattach.

warning The gas rail fuel nozzle must be reengaged within the burner opening.

CUSTOMER SERVICE
Visit us online at blackstoneproducts.com/support for assistance concerning appliance use, replacement parts, or your warranty.

CUSTOMER SERVICE HOURS:
Monday – Friday 7:00 am – 5:00 pm (MST)

Documents / Resources

References

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download BLACKSTONE 2177 - 36" GRIDDLE Manual

Advertisement

Need help?

Need help?

Do you have a question about the 2177 and is the answer not in the manual?

Questions and answers

Table of Contents