Remote Control - Pioneer VSX-33TX Operating Instructions Manual

Displays & Controls

Remote Control

1
SOURCE
DVD TV
2
MULTI CONTROL
CD CD-R
1
LOUDNESS
3
4
INPUT ATT
7
REMOTE SETUP SYSTEM SETUP SIGNAL SELECT
+10
EFFECT/CH SEL
4
TV VOL
4
5
TUNE
ST
6
7
TUNE
8
GUIDE
D.ACCESS
9
&
MPX
0
¶
-
RETURN S.MODE
=
RECEIVER DIRECT CONTROL
MIDNIGHT DSP
~
THX ADVANCED STANDARD MUTE
!
2
@
#
AV PRE-PROGRAMMED AND LEARNING
$
REMOTE CONTROL UNIT
1 SOURCE
button
Use to turn on/off other components connected to
the receiver.
2 MULTI CONTROL buttons
Use to put the receiver/remote control in the
stated mode.
For other equipment controls, see Controlling the
Rest of Your System on pages 55-59.
3 Number/MODE buttons
Use the number buttons to select the radio
frequency in tuner DIRECT ACCESS mode or the
tracks in CD, DVD mode etc.
Also, buttons marked with the following names
have special functions. If you try to use one of
these functions but the display flashes it means
that function cannot be used in the current mode
(for example DSP modes cannot be used when 5.1
CH setting is on).
LOUDNESS button
Use to switch on the loudness. This feature is
useful for getting good bass and treble sounds
listening at low volumes.
24
%
^
RECEIVER
VCR VCR
1 2
TUN TVC
2 3
VIDEO SELECT MULTI CH INPUT
5 6
DIGITAL NR FL DIMMER
8 9
DISC
0
ENTER
&
RECEIVER
*
TV MASTER VOLUME
TV CONTROL
TVFUNC
¢
CHANNEL
ST
ENTER
(
MENU
)
BAND CLASS
‹ *
_
DTV ON / OFF DTV MENU
! ⁄
+
CLEARDTV INFO
¡
RDM
STEREO FUNCTION
™
£
Î ¢
/ DTS
∞
VIDEO SELECT button
Switches the receiver between the various
types of video input.
MULTI CH INPUT button
Use to hook up an external component that can
decode other types of signals and input them
into the VSX-33TX (see p.48).
INPUT ATT button
Use to lower the input level of an analog signal
that is too powerful, thus causing the sound to
distort (the OVER indicator will light when this
is the case).
DIGITAL NR button
Press to switch Digital NR on or off. (See page
45)
FL DIMMER button
Use to adjust the brightness of the fluorescent
display (FL = fluorescent display).
Four levels of the brightness ranging from very
dim to very bright can be selected. Each press
changes the brightness of the display.
REMOTE SETUP button
Use to customize the remote control functions
and the remote control itself. (See "Remote
Control of Other Components" starting on
p.55.)
SYSTEM SETUP button
Use to set up the speaker and sound systems.
For more information see "Setting Up for
Surround Sound" starting on p.27.
SIGNAL SELECT button
Press SIGNAL SELECT repeatedly to select one
of the following:
ANALOG – Analog signal.
DIGITAL – Digital signal (DVD/LD, TV/SAT, CD,
CD-R/TAPE 1/MD, VCR 1/DVR, VCR 2).
AUTO – This is the default. If there are analog,
or digital signals input the receiver automatical-
ly selects the best possible signal.
EFFECT / CH SEL button
For DSP/advanced theater sound modes use to
put into the mode to add or subtract the amount
of effect. For other sound modes use to select
individual channels to increase or decrease
channel level.
EFFECT +/– buttons
Use to add or subtract the amount of effect in
different DSP/advanced listening sound modes or
the level of individual channels.
ENTER button (DISC)
Use to enter commands into TVs or DTVs. For CD
players use to change discs.