Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for thomann THV 3.0
Summary of Contents for thomann THV 3.0
- Page 1 THV 3.0 Vibraphone...
- Page 2 Thomann GmbH Hans-Thomann-Straße 1 96138 Burgebrach Germany Telephone: +49 (0) 9546 9223-0 Internet: www.thomann.de 10.07.2024, ID: 251497 (V2)
-
Page 3: Table Of Contents
Setup............................. 7 3.1 Assembling the frame....................7 3.2 Inserting the motor......................8 3.3 Inserting the struts and hooking in the resonators..........8 3.4 Installing the dampers....................10 3.5 Installing the sound bars.................... 11 Protecting the environment................... 12 THV 3.0 Vibraphone... - Page 4 THV 3.0 Vibraphone...
-
Page 5: General Information
Our products and documentation are subject to a process of continuous develop‐ ment. They are therefore subject to change. Please refer to the latest version of the documentation, which is ready for download under www.thomann.de. 1.1 Symbols and signal words In this section you will find an overview of the meaning of symbols and signal words that are used in this document. -
Page 6: Safety Instructions
The plasticiser contained in the rubber feet of this product may react with the coating of the floor and cause permanent dark stains after some time. If necessary, use a suitable mat or felt slide to prevent direct contact between the device’s rubber feet and the floor. THV 3.0 Vibraphone... -
Page 7: Setup
Press the right end of the pedal rod (7) towards the wide lower part (2) until you feel spring resistance, and insert the pedal rod (7) in the seat of the narrow lower section (4). Tighten the wing screw. THV 3.0 Vibraphone... -
Page 8: Inserting The Motor
Insert the pre-assembled unit consisting of strut 2 (13), strut 3 (14) and damper bar ö (15) into the designated seats in the upper sections (1, 3). When inserting them, ensure that the numbers attached to the struts and the seats in the upper sections match. THV 3.0 Vibraphone... - Page 9 (19) as shown. Insert strut 1 (20), strut 4 (21) into the designated seats in the upper sections (1, 3). When inserting them, ensure that the numbers attached to the struts and the seats in the upper sections match. THV 3.0 Vibraphone...
-
Page 10: Installing The Dampers
Hook the pedal control rod (23) into the eyelet on the bottom of the damper bar (15). Lock the pedal control rod in place with the double bell. Hook the pedal control rod (23) into the seat on the pedal rod (7) as shown. THV 3.0 Vibraphone... -
Page 11: Installing The Sound Bars
Connect the tension springs on the ends of the string to each other. Pay attention to the different string routing for hook pegs (27) and saddle pegs (28). < Press the pedal to make it easier to place the string under the hook. THV 3.0 Vibraphone... -
Page 12: Protecting The Environment
You can also return your old device to Tho‐ mann GmbH at no charge. Check the current conditions on www.thomann.de. Proper disposal protects the environment as well as the health of your fellow human beings. - Page 13 Notes THV 3.0 Vibraphone...
- Page 14 Notes THV 3.0 Vibraphone...
- Page 16 Musikhaus Thomann · Hans-Thomann-Straße 1 · 96138 Burgebrach · Germany · www.thomann.de...
Need help?
Do you have a question about the THV 3.0 and is the answer not in the manual?
Questions and answers