Download Print this page

Advertisement

Quick Links

1455 Kleppe Lane Sparks, NV 89431-6467 (775) 359-4712 Fax (775) 359-7424
NOTE TO INSTALLER: Please leave this information with the Maintenance Department.
Haws electric water cooler's are not designed or recommended for outdoor or
corrosive environments such as enclosed chlorinated pool areas.
Consideration must be made at the time of installation to adhere to state and/or local
codes and environmental/atmospheric conditions such as, but not limited to, dust,
corrosion, freezing etc. These conditions will void the warranty.
CAUTION! Prior to making any electrical connections, verify with a voltmeter that power
from the service panel is off.
HAWS warrants that this specific product is guaranteed against defective material or
poor workmanship for a period of one year from date of shipment. HAWS liability
under this warranty shall be discharged by furnishing without charge F.O.B. HAWS
Factory any goods, or part thereof, which shall appear to the Company upon
inspection to be of defective material or not of first class workmanship, provided that
claim is made in writing to Haws within a reasonable period after receipt of the
product. Where claims for defects are made, the defective part or parts shall be
delivered to the Company, prepaid, for inspection. HAWS will not be liable for the
cost of repairs, alterations or replacements, or for any expense connected therewith
made by the owner or his agents, except upon written authority from HAWS,
Sparks, Nevada. HAWS will not be liable for any damages caused by defective
materials or poor workmanship, except for replacements, as provided above. Buyer
agrees that HAWS shall not be liable for general, special, or consequential damages
claimed to arise under the contract of sale. The drinking fountain manufactured by
HAWS is warranted to function if installation and maintenance instructions provided
are adhered to. The units also must be used for the purpose for which they were
intended.
NO OTHER WARRANTIES EXPRESSED OR IMPLIED ARE AUTHORIZED,
PROVIDED OR GIVEN BY HAWS.
03/17
E-mail:
haws@hawsco.com
Model H1011.8HO
Water Cooler
LIMITED WARRANTY
MODEL H1011.8HO
INSTALLATION, OPERATION
MAINTENANCE INSTRUCTIONS
 website:
www.hawsco.com
&
No. 2080250 (22)
PAGE 1 OF 9

Advertisement

loading
Need help?

Need help?

Do you have a question about the H1011.8HO and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Haws H1011.8HO

  • Page 1 Haws within a reasonable period after receipt of the product. Where claims for defects are made, the defective part or parts shall be delivered to the Company, prepaid, for inspection.
  • Page 2: Technical Support

    10" pipe wrench, 3/32” and 5/32 “ hex key wrench, 9/16”, 1/2", 7/16” socket wrench or open end wrench. LOCATION OF UNIT: The Model H1011.8HO Cooler is a wheelchair accessible drinking facility. The height dimensions shown, meet current ADA requirements. When installing this unit, local, state or federal codes should be adhered to.
  • Page 3: Installation Procedure

    INSTALLATION PROCEDURE GENERAL NOTES: The Model H1011.8HO Water Cooler Assembly requires installation of the mounting frame as described in Steps 1 – 2, then mounting the fountain bowl assembly as described in Steps 3 – 6, and finally completing chiller water and electrical connections and starting chiller per Steps 7 –...
  • Page 4 Remove slip joint nuts from bottom of fountain waste outlet. Assemble nut over 1- 1/4” O.D. end of waste elbow as supplied by Haws. Assemble waste elbow onto bowl waste body using seal washer provided and tighten nut hand tight. Measure vertical distance down to trap inlet and cut the vertical (not supplied) elbow to length allowing 1/2"...
  • Page 5 Verify the chiller turns off after water reaches proper temperature. If there are any problems, refer to Sensor/Solenoid Troubleshooting Guide. STEP 13: Install grille and tighten outer side screws. Verify there is chilled water out of bubbler. 03/17 MODEL H1011.8HO PAGE 5 OF 9...
  • Page 6: Maintenance

    Remove any debris clogging the screen openings and place back into nozzle body. Reassemble nozzle insert. Water too warm or cold. Adjust chiller temperature control, clockwise for colder water. 03/17 MODEL H1011.8HO PAGE 6 OF 9...
  • Page 7 For more information about Haws products, see our website: www.hawsco.com ® © 2017 Haws Corporation – All Rights Reserved ® HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation. 03/17 MODEL H1011.8HO PAGE 7 OF 9...
  • Page 8: Parts Breakdown

    WHEN ORDERING PARTS PLEASE SPECIFY MODEL NUMBER. DRINKING FOUNTAIN APPROVED DATE 07/08/17 SCALE: DRAWING TYPE: PARTS BREAKDOWN SIZE: A SHEET 2017 Haws Corporation - All Rights Reserved PAGE 8 of 9 HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.
  • Page 9 DRAWN: DATE: CHK'D.: REVISION 07/97 DRINKING FOUNTAIN APPROVED: DATE: 07/07/17 SCALE: 1/18 DRAWING TYPE: INSTALLATION SIZE: A SHEET 2017 Haws Corporation - All Rights Reserved. HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.