Haws 1201S Installation, Operation & Maintenance Instructions Manual
Electric water cooler and bottle filling stations
Hide thumbs
Also See for 1201S:
Advertisement
Quick Links
1455 Kleppe Lane Sparks, NV 89431-6467 (775) 359-4712 Fax (775) 359-7424
E-mail:
Electric Water Cooler and Bottle Filling Stations
MODELS 1201S / 1201SF / 1211S / 1211SF / 1202S / 1202SF / 1212S / 1212SF
NOTE TO INSTALLER: Please leave this information with the Maintenance Department.
CAUTION: Disconnect electrical power to outlet before installing or servicing.
NOTICE:
A. The electrical receptacle must have code-approved ground-fault circuit
interrupter (GFCI) protection for personnel.
B. Care should be taken not to damage refrigeration system lines or
electrical wires during installation.
C. Installation must conform to all applicable codes and standards.
SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF THIS
MODEL PLEASE CALL:
TECHNICAL SUPPORT:
FOR CUSTOMER SERVICE:
08/2019 Models 1201S / 1201SF / 1211S / 1211SF / 1202S / 1202SF / 1212S / 1212SF
haws@hawsco.com
SAFETY PRECAUTIONS
1-800-766-5612
1-888-640-4297
INSTALLATION, OPERATION
MAINTENANCE INSTRUCTIONS
website:
www.hawsco.com
&
No. 0510000866 (1A.2)
Page 1 of 11
Advertisement
Related Manuals for Haws 1201S
Summary of Contents for Haws 1201S
- Page 1 SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF THIS MODEL PLEASE CALL: 1-800-766-5612 TECHNICAL SUPPORT: 1-888-640-4297 FOR CUSTOMER SERVICE: 08/2019 Models 1201S / 1201SF / 1211S / 1211SF / 1202S / 1202SF / 1212S / 1212SF Page 1 of 11...
- Page 2 To remove, depress collet and pull tubing out. Tube OD Size OD Tolerance Insertion Depth 1/4” ±.004” 11/16” 3/8” ±.004” 3/4” 08/2019 Models 1201S / 1201SF / 1211S / 1211SF / 1202S / 1202SF / 1212S / 1212SF Page 2 of 11...
- Page 3 20. Remove the protective plastic film from the sensor area of the bottle filler. 21. If installing a high/low unit, proceed to those steps. If not, proceed to START-UP section. 08/2019 Models 1201S / 1201SF / 1211S / 1211SF / 1202S / 1202SF / 1212S / 1212SF Page 3 of 11...
- Page 4 Figure 4: Programming Mode Button viewed from Replace the clear plastic cover after programming the unit. underside of bowl 08/2019 Models 1201S / 1201SF / 1211S / 1211SF / 1202S / 1202SF / 1212S / 1212SF Page 4 of 11...
- Page 5 “on 6” the “P”, then “oFF 5” and “A”. 08/2019 Models 1201S / 1201SF / 1211S / 1211SF / 1202S / 1202SF / 1212S / 1212SF Page 5 of 11...
- Page 6 Replace lower bowl support cover with (4) screws and turn on power to the unit Figure 7: Fuse Replacement view from underside of bowl 08/2019 Models 1201S / 1201SF / 1211S / 1211SF / 1202S / 1202SF / 1212S / 1212SF Page 6 of 11...
- Page 7 Solid ON = Basic or Programmable Energy Saving Mode enabled Intermittent Flash = Unit actively saving energy (compressor and fan disabled) OFF = Energy Saving Mode disabled 08/2019 Models 1201S / 1201SF / 1211S / 1211SF / 1202S / 1202SF / 1212S / 1212SF Page 7 of 11...
-
Page 8: Troubleshooting
Unit self-purges every 24 hours if not used. Clean the bottle filler sensor lens with mild detergent and water. 08/2019 Models 1201S / 1201SF / 1211S / 1211SF / 1202S / 1202SF / 1212S / 1212SF Page 8 of 11... - Page 9 Clear error in programming mode and RFID board lost communication power cycle unit and check error to validate. Check cable connection to RFID board. 08/2019 Models 1201S / 1201SF / 1211S / 1211SF / 1202S / 1202SF / 1212S / 1212SF Page 9 of 11...
- Page 10 Haws Corporation. 1455 Kleppe Lane, Sparks, Nevada 89431 – 800.766.5612 – www.hawsco.com 08/2019 Models 1201S / 1201SF / 1211S / 1211SF / 1202S / 1202SF / 1212S / 1212SF Page 10 of 11...
- Page 11 (e.g., if a replacement cooler is installed 8 months after installation of the original cooler, the replacement cooler will be warrantied for 4 months from installation.). Haws’ duty also includes costs of outbound freight (but not express freight) of the part or parts from the factory repair department, but only if the part or parts, and the purported defect or defects, are covered by this Limited Warranty, in Haws’...