Subscribe to Our Youtube Channel
Related Manuals for CHANCEE XR 2D 97/300 W
Summary of Contents for CHANCEE XR 2D 97/300 W
- Page 1 Ride on Floor Scrubber Operation Instructions XR 2D 97/300 W It is strictly prohibited to use this equipment without reading this manual.
-
Page 3: Preface
Preface Thank you for choosing Chancee cleaning equipment. We are confident in providing you with this product which is manufactured using the latest technology and has undergone strict quality control. This manual is used to help you understand the operation and maintenance of the equipment so that you can use it more comfortably and efficiently, so please read this manual thoroughly before using. - Page 4 be strictly followed. In this manual, we use the symbol with the word "Caution" indicates the possibility of dangers that may cause minor or moderate personal injury or equipment damage; in order to avoid or reduce the danger, the relevant steps must be strictly followed. ) A mark similar to this indicates that the direction to which the arrow points is forward.
-
Page 5: Table Of Contents
Contents Preface ........................................3 Safety Precautions ..................................3 Safe use ......................................3 Chapter 1 Product Introduction ...............................1 1.1 Applicable Scenarios ................................1 1.2 Equipment Overview ................................1 1.3 Control Panel/Buttons ................................ 2 1.4 Technical parameters ................................3 1.5 Accessories list ..................................3 1.6 Consumables and Optional Accessories ........................3 Chapter 2 Installation ...................................4 2.1 Unloading ....................................4... -
Page 6: Chapter 1 Product Introduction
Chapter 1 Product Introduction 1.1 Applicable Scenarios This equipment can be used in a variety of scenarios, including commercial and industrial places , such as hotels, schools, hospitals, industrial offices, supermarkets, office buildings, etc.; for epoxy floors, PVC floors, terrazzo, wear-resistant floors, tiles and cement floors , wooden floors, rubber floors, different floors can be cleaned with brush plates made of different materials. -
Page 7: Control Panel/Buttons
Side-brush module Clean the position of wall, corner and other position ⑮ Brush plate Clean the floor ⑯ Headlight Lighting the environment ⑰ Solution tank cover Observe the water tank and the water adding position of the ⑱ water tank Solution tank Store clean water ⑲... -
Page 8: Technical Parameters
1.4 Technical parameters Name Value Name Value Brush motor power（W） 650*2 200*1 Cleaning width（mm） 1000 （side brush） Driving motor power Squeegee width（mm） 1200 1400 （W） Continuous running Clean water capacity（L） hour（h） Theoretical working Sewage capacity（L） 10000 efficiency（㎡/h） 36/400(Refill liquid） Total weight（kg） Battery capacity（V/Ah）... -
Page 9: Chapter 2 Installation
Chapter 2 Installation 2.1 Unloading Caution： Please remove the outer packaging carefully to avoid damaging the machine shell; It is recommended to keep the packaging boxes of related products after receiving the goods, so that the machine can be repackaged later when the equipment is moved or returned or exchanged; It is prohibited to violently unload the machine from the pallet to avoid damaging the parts;... -
Page 10: Chapter 3 Inspection Before Use
Chapter 3 Inspection before use 3.1 Check the battery After turning on the power key switch, the battery meter will display the current voltage of the battery. When the voltage is about 31.5V or on red alert, please charge it in time. Caution：... -
Page 11: Chapter 4 Operation Instructions
Chapter 4 Operation instructions 4.1 Driving Step 1：Turn on the main power key switch of the machine; Step 2：Turn the forward/backward switch as needed, and lightly press the accelerator pedal to move the machine forward and backward; Step 3：When the machine needs to stop, release the accelerator pedal and simultaneously step the brake pedal until the machine comes to a complete stop, flip the forward and backward switch to the middle position. -
Page 12: Discharging Sewage
4.3 Discharging sewage Step 1 ： Push the machine to a site that meets the sewage discharge standards, stop the machine, and turn off the power; Step 2 ： Remove the sewage tube from the clamp at the rear of the machine, place it downwards, open the tube cover, and discharge the water. -
Page 13: Chapter 5 Cleaning And Maintenance
· Check whether the battery connection wire is worn and whether the contacts are loose, and replace it if necessary; · The battery terminals should be kept clean and dry, without debris and dust covering them, otherwise it will be extremely detrimental to the battery, and in serious cases, it will burn the battery; ·... - Page 14 brush plate; Step 3: When installing the brush plate, ensure that the inner diameter of the brush plate is aligned with the magnetic ring, and lift the brush plate to a certain distance. After the magnetic ring catches the brush plate, the installation is complete.
-
Page 15: Squeegee Adjustment
Installation of rubber strips Step 1：Align the holes of the front rubber strip with the protrusions of the component of the squeegee, and fix the plastic bottom plate to the bottom plate of the squeegee; Step 2： Align the holes of the rear rubber strip with the protrusions of the component of the squeegee; install the rubber strip pressure plate and lock the buckle;... -
Page 16: Chapter 6 Transportation And Storage
Chapter 6 Transportation and Storage 6.1 Transportation If the machine and the accessories need to be lifted, it is recommended that you put them on a pallet and lift them with a forklift. And water in both tanks must be emptied when transporting the machine; In order to prevent slipping and damage caused by collisions during transportation, please ensure that the binding should be firm and the center of gravity should be stable to ensure safety. -
Page 17: Chapter 7 Common Faults
Chapter 7 Common faults Fault Phenomenon/Part Troubleshooting Solution If the charger is not connected to the machine, see whether the green light Charger failure will be on. If the machine is plugged Replace the charger in, the red light is on, and the built-in Charging failure fan of the charger does not run... - Page 18 Worn brush plate Observe the wear Replace the brush plate buckle buckle Floating ball cage Check the floating balls in the cage Need extra attention in daily use clogged Need daily cleaning Tube blocked Clean the water suction tube machine maintenance Recovery tank...
-
Page 19: Warranty Card
Warranty Card Name Tell Postal address Bill No. Purchase time Number Product model Date Replace accessories Fault description — 14 —... - Page 20 — 15 —...
Need help?
Do you have a question about the XR 2D 97/300 W and is the answer not in the manual?
Questions and answers