Oki B8300 Installation Manual page 4

B83LT Installation Manual
FOR USE WITH COMPATIBLE OKI DIGITAL PRINTERS.
SEE OKI DIGITAL PRINTER SERVICE MANUAL OR
INSTALLATION MANUAL TO DETERMINE SUITABILITY.
<Before installation>
• Start installation after checking that the DATA and
COMMUNICATION indicators on the operation panel are
neither lit nor blinking.
• For installation, a power supply unit is needed.
<Parts included>
Front mounting Rear mounting Screws (M4x8):
plates: 2 pcs. plates: 2 pcs. 4 pcs.
Left adjuster: 1 pc.
Left paper guides: 2 pcs. Right paper guides: 2 pcs.
Adjuster covers: 4 pcs.
1. Turn off the main switch of the main unit of the printer.
Turn the main switch located on the front side of
the printer to the "OFF" position.
Then remove the power plug from the outlet.
"OFF"
2. Attach the adjusters and adjust them.
<1> Insert the left adjusters to
3
the stand/paper drawer.
<2> Turn each adjuster to
lower it until it touches the floor.
<3> Attach the four adjuster
covers.
3
Be sure to attach the left 2
adjuster to prevent overturning.
[Caution] The lower tray
2
cannot be pulled out unless
the adjuster is lowered to the
specified position.
1
2
3. Put the main unit of the printer on the stand/paper drawer.
<1> Pull out the paper tray of
the main unit until it stops and
then remove it by lifting both
ends of the tray.
<2> Hold the main unit of the
printer at the positions shown
in the illustration and put the main unit on the
stand/paper drawer so that the front side and the
left side of the main unit are aligned to those of
the stand/paper drawer.
Front side
Rear side
[Caution]
For installation of the main unit, it must be
held by two persons and installed carefully.
4. Connect the main unit to the stand/paper drawer.
<1>Attach the two rear
mounting plates using a
supplied screw for each.
Rear
mounting plate
Rear mounting plate
Stand frame
[Caution]
Insert the rear mounting
plates under the Stand frame.
<2>Pull out the upper tray
of the stand/paper drawer
until it stops, and attach the
two front mounting plates
using a supplied screw for
each.
Then, remove the lock of
the paper tray and close the
tray.
Screw
Front mounting plate
<3> Reattach the paper tray
of the main unit.
3
2
3
5. Remove the rear cabinet of the stand/paper drawer and
remove the AC inlet cover.
<2> Remove the screw that fixes the
<1> Remove the four screws that
fix the rear cabinet and then AC inlet cover and then remove the
AC inlet cover.
remove the rear cabinet.
<3> Cut out the AC inlet cover as
shown in the illustration.
Cut out.
Rear cabinet
6. Attach the power supply unit.
Attach the power supply unit to the brackets and secure it using the three
supplied screws.
Bracket
Bracket
Power supply unit
Screws
7. Connect the power supply unit harness to the PCU PWB
of the main unit of the printer.
Rear mounting plate
<1> Remove the screw that
fixes the harness cover of the
main unit of the printer and
slide the harness cover up to
remove it.
Screw
Screw
Cut out the harness cover as
shown in the illustration.
<2> Connect the optional
Front
power supply harness
mounting plate
connector to CN11 (red
connector) of the PCU PWB of
the main unit of the printer.
Screw
<3> Reattach the harness
cover to its original position
and fix it with the removed
screw.
At this time, ensure that the
optional power supply harness
are arranged as shown in the
illustration.
• Fix the harness securely to
the wire saddle.
8. Connect the relay harness of the stand/paper drawer to
the power supply unit.
Connect the relay harness of
the stand/paper drawer to the
connector of the power supply
unit.
Relay harness of the
stand/paper drawer
9. Attach the rear cabinet of the stand/paper drawer.
AC inlet cover
<1> Pass the cord of the power supply
unit through the hole of the rear cabinet
and attach the rear cabinet to the
stand/paper drawer.
Rear cabinet
Screws
10. Connect the AC cord of the power supply unit to the
main unit of the printer.
Connect the AC cord of the
Screw
power supply unit to the inlet
connector of the main unit of
the printer at the location
shown in the illustration.
Cut out.
11. Attach the paper guides to the lower tray.
Harness cover Remove the four screws for
packing. (See
illustration.)
Connector
Insert the left paper guides and
CN11
right paper guides to the front
and rear guide slots for the
paper size to be used. (See the
illustration below.)
(For the AB system, set the
guides to A4. For the inch
system, set the guides to LT.)
Left paper guides
Screw
Optional power
supply harness
Harness cover
Wire saddle
Wire saddle
* If another peripheral device must be installed, carry out
the following step at the end of the installation work.
Connector of the power supply connector
12. Adjust the position of the paper guides of the upper
paper tray of the stand/paper drawer.
<1> To use the setting mode, insert the power plug of the main unit of the
printer to the outlet and turn the main switch on while pressing the [MENU]
key and the [OK] key of the operation panel of the main unit of the printer.
<2> Press the [MENU] key several times to display "SIZE ADJUSTMENT
A" and press the [OK] key.
<3> "MAXIMUM SIZE" is displayed.
Pull out the paper tray and extend the paper guides to the maximum.
Then, return the paper tray into the unit and press the [OK] key.
<4> "MINIMUM
displayed. Pull out the paper
<2> Attach the AC inlet cover tray again and narrow the
to the rear cabinet of the
paper guides to the minimum.
stand/paper drawer and fix it
Then, return the paper tray into
with the removed screw. the unit and press the [OK] key.
(The rear guide need not be
adjusted.)
[Caution] If the setting above
is not carried out, the paper
detection function
operate.
13. Carry out the off center adjustment.
AC inlet cover
Installation is now complete.
Screw
3
AC cord
the right
Right paper guides
Paper guide
SIZE" is
Rear guide
Paper guides
will not