Page 7
European Conformity Statement Unitech Electronics co., Ltd herewith declares that the Unitech product is in compliance with the essential requirements and all other provisions of the RED 2014/53/EU directive. The declaration of conformity is available for download at: https://portal.Unitech.eu/public/Safetyregulatorystatement UK Declaration of Conformity (DoC) Hereby, Unitech Electronics co., Ltd.
Waste electrical and electronic equipment (WEEE) Unitech has set up a policy and process to meet the 2012/19/EU concerning electronic waste disposal. For more detailed information of the electronic waste disposal of the products you have purchased from Unitech directly or via Unitech’s resellers, you shall either...
Laser Information The Unitech product is certified in the U.S. to conform to the requirements of DHHS/CDRH 21CFR Subchapter J and to the requirements of IEC 60825-1. Class II and Class 2 products are not considered to be hazardous. The Unitech product contains internally a Visible Laser Diode (VLD) whose emissions do not exceed the maximum limits as set forth in the above regulations.
Do not leave the battery uncharged and unused for an extended period of time, the battery will wear out and the longevity of the battery will be at least half of one with frequent charges. Despite Unitech’s safety precautions, the battery pack may experience changes in shape or swelling.
Page 12
It may not be functional anymore. 5. Please only use the original battery from Unitech. Using a third party battery can damage our products. Please note that when such damage occurs, it is not covered by Unitech’s warranty policy.
Unitech product for charging. Please remove the power adapter when the battery is fully recharged. The bundled power adapter that comes with your Unitech product is not meant to be used outdoors. An adapter exposed to water or rain, or a very humid environment can cause damage to both the adapter and the product.
Worldwide Support Unitech’s professional support team is available to quickly answer questions or assist with technical-related issues. Should an equipment problem occur, please contact the nearest Unitech regional service representative. For complete contact information please visit the Web sites listed below: Taipei, Taiwan –...
The warranty period is varied from each country. Please consult with your supplier or Unitech local office for actual length of warranty period to your purchased product. Warranty becomes void if equipment is modified, improperly installed or used, damaged by accident or neglect, or if any parts are improperly installed or replaced by the user.
EA660 User’s Manual EA520 User’s Manual Chapter 1 - Overview 1.1 Package Please make sure the following contents are in the EA660 gift box. If something is missing or damaged, please contact your Unitech representative. The Package Contents EA660 Rugged Handheld Computer ...
QC (quick charge) USB-C cable and a QC adapter, or a cradle. Connect the USB-C cable to the USB port on the EA660, and plug the other end of the USB cable into the AC power adapter. Then, insert the AC power adapter into the electrical outlet.
Page 42
EA520 User’s Manual Make sure that both devices are unlocked and have NFC turned on. Also make sure that the NFC antenna area of EA660 and the other phone's NFC area are close to one another. Slightly moving the phones until a connection is made.
For the instruction, please refer to 1.4.7 Inserting the Micro SD/Nano SIM Card 2. Turn on the EA660, LTE signal will show at the top of the screen. 2.3.1 Mobile Network Settings On the main screen, scroll the screen from bottom to top to reach the APPS, and tap Settings and then tap Network &...
EA660 User’s Manual EA520 User’s Manual 2.7 PC Setting Connect EA660 to your computer with the USB Type C cable. Your computer will recognize it is USB charging. Slide down from top, the system will show as follow picture, then you can tap on Android System Charging this device via USB.
EA520 User’s Manual 2.10 Performing A Hardware Reset You may have to perform a reset if the device freezes (i.e., the EA660 no longer responds to the buttons or tapping on the screen). Long press and hold the Power button around 10 seconds to restart the device.
EA660 User’s Manual EA520 User’s Manual 2.12 KeyRemap The EA660’s keys can be programmed for users to be able to perform different functions or applications. Four options to use key remap functions: Volume_Up/Down, Programmable Key, Scanner Triger Key Left and Scanner Triger Key Right.
Page 79
EA520 User’s Manual Solution Introduction StageGO is a barcode-based device staging solution from Unitech that helps IT admins to swiftly set up a device by just a few barcode scans. StageGO For versatile functions of RFID command via integrating with Unitech RFID Readers.
3.2.3 Picklist Mode Picklist mode enables EA660 to decode only barcodes that are aligned under the laser crosshair or LED aiming dot. For picklist mode demonstration, please click on our Youtube channel for more information : https://www.youtube.com/watch?v=QjT2E6hxD_k...
No technical skills required. Simply use the Start-Stop buttons to start recording vital system and app logs as one snapshot or as a time-lapse, and then the logs can be automatically submitted to the unitech support team for analysis.
StageGO helps IT admins to swiftly set up a device by just a few barcode scans. Features Swift and effortless device staging for Unitech Android Mobile Devices. Device staging becomes more accessible, time-efficient, and secure. Complete device control at your fingertips.
Need help?
Do you have a question about the EA660 and is the answer not in the manual?
Questions and answers