Page 4
Use of other accessories may not ensure compliance with FCC RF exposure guidelines. European Conformity Statement unitech Electronics co., Ltd herewith declares that the unitech product is in compliance with the essential requirements and all other provisions of the RED 2014/53/EU directive.
Page 6
Waste electrical and electronic equipment (WEEE) unitech has set up a policy and process to meet the 2012/19/EU concerning electronic waste disposal. For more detailed information of the electronic waste disposal of the products you have purchased from unitech directly or via unitech’s resellers, you shall either...
Page 8
Laser Information The unitech product is certified in the U.S. to conform to the requirements of DHHS/CDRH 21CFR Subchapter J and to the requirements of IEC 60825-1. Class II and Class 2 products are not considered to be hazardous. The unitech product contains internally a Visible Laser Diode (VLD) whose emissions do not exceed the maximum limits as set forth in the above regulations.
Page 9
It may not be functional anymore. Please only use the original battery from unitech. Using a third party battery can damage our products. Please note that when such damage occurs, it is not covered by unitech’s warranty policy.
Page 11
Please remove the power adapter when the battery is fully recharged. The bundled power adapter that comes with your unitech product is not meant to be used outdoors. An adapter exposed to water or rain, or a very humid environment can cause damage to both the adapter and the product.
Page 13
Worldwide Support unitech’s professional support team is available to quickly answer questions or assist with technical-related issues. Should an equipment problem occur, please contact the nearest unitech regional service representative. For complete contact information please visit the Web sites listed below: Taipei, Taiwan –...
Page 14
The warranty period is varied from each country. Please consult with your supplier or unitech local office for actual length of warranty period to your purchased product. Warranty becomes void if equipment is modified, improperly installed or used, damaged by accident or neglect, or if any parts are improperly installed or replaced by the user.
PA726 User’s Manual Chapter 1 - Overview 1.1 Package Please make sure the following contents are in the PA726 gift box. If something is missing or damaged, please contact your unitech representative. The standard package contents PA726 Terminal ...
Page 30
After PA726 is connected to the charging cable, push up the release buttons on the both sides of the USB charging cable to lock PA726. Use USB charging cable to connect the AC adapter. Plug the AC adapter cord into an electrical outlet.
Page 32
PA726 User’s Manual 1.4.5 Using the Micro SD/ Micro SIM Card The PA726 has Micro SD/ Micro SIM card slots inside the battery compartment. Inserting a Micro SD/ Micro SIM Card To loosen the two knobs on the battery cover by turning counterclockwise.
Page 35
PA726 User’s Manual 1.4.6 Battery Status The PA726 provides battery info for users to check the battery status, history view and also set up users preferences. go to APPS, and tap Settings and then under system, tap BatteryInfo. BatteryInfo shows the details of the battery use.
Android Beam option, make sure it is also turned on. Make sure that the NFC antenna area of PA726 and the other phone's NFC area are close to one another. Slightly moving the phones until a connection is made.
It only applies to the device which supports WWAN. 2. Turn on the terminal, 4G signal will show at the top of the screen. If you insert 3G SIM card into PA726, the icon is displayed on the status bar.
Page 47
PA726 User’s Manual 2.6.1 WLAN setting via Wifi Scan Configuration EZsetup provides users the quickest way for PA726 to connect Wifi by scanning Wifi QR code through EZSetup QR code generator. 1. Please click the link below to start EZSetup QR code generator.
Normally, you can easily reconnect your device by switching on Bluetooth ® PA726, and then turning on the device. However, you might have to connect manually if PA726 has been used with another Bluetooth ® device.
PA726 User’s Manual 2.9 PC Setting Connect PA726 to your computer with the USB cable. Your computer will recognize it is USB charging. Release Buttons Push up : Lock Push down: Unlock Slide down from top, the system will show as follow picture, then you can select File transfers.
PA726 User’s Manual 2.13 Programmable Keys The PA726’s keys can be programmed for users to be able to perform different functions or applications. 2.13.1 Programming a key go to APPS, and tap Settings. Go to SYSTEM, Tap Programmable keys, and select the keys to remap.
Page 65
PA726 User’s Manual 2.13.2 Enable/ Disable wakeup After the key is mapped to a key code, check the Enable wakeup checkbox to wake PA726 by pressing the programmable keys when PA726 is in sleep mode. Note: This function only applies to KEYCODES.
Swap. 2. The LED indicator will start showing solid red light. Please swap the battery after the LED red light goes off. Please do not turn on PA726 during the battery swap. 3. When the battery swap is done, you can press the power button to restart PA726 again.
PA726 User’s Manual 3.5 MoboLink MoboLink is a software platform that helps unitech customers to remote manage their purchased devices and applications. The core of the MoboLink platform provides functionalities in the MDM (Mobile Device Management) and MAM (Mobile Application Management) domains, and then further extends into other management functions such as alert notification management and account management.