Subscribe to Our Youtube Channel
Related Manuals for Creative Play OCTAVIA COMPLETE OS111
Summary of Contents for Creative Play OCTAVIA COMPLETE OS111
- Page 1 OS111 - OCTAVIA COMPLETE (4M) Installation Instructions REF: OS111 pg 1 of 17 23.07.2019...
-
Page 2: Parts Required
PARTS REQUIRED SIDE ASSEMBLIES - QTY x 7 SEAT SLATS - INNER (SET) x5 SS-I SEAT SLATS -END (SET) x2 SS-E SEAT SUPPORT ASSEMBLY x6 SSA-I (INNER) SEAT SUPPORT ASSEMBLY x2 SSA-E (END) SEATING & SIDES PARTS / ASSEMBLIES UPRIGHT MAIN TIMBER UMT - QTY x8 UPRIGHT ADDITIONAL TIMBER UAT - QTY x4... - Page 3 PARTS REQUIRED QTY x 25 - 4.8m LENGTHS FLOOR - DECKING DECKING (to be cut on site) QTY x 2 FLOOR ASSEMBLY QTY x 8 FLOOR SURROUND ASSEMBLY QTY x 3 - FS-A FLOOR SUPPORTS QTY x 2 - FS-B QTY x 4 - FS-C FLOOR PARTS / ASSEMBLIES x 348...
- Page 4 PARTS REQUIRED ROOF TRIM / KING ‘POST’ QTY x 1 - RT1 - ROOF CAP QTY x 1 - RT2 - KING POST QTY x 4 - RT3a - 6x1 TRIM QTY x 4 - RT3b - 6 x 1 TRIM ROOF ASSEMBLIES QTY x 8 - RA - ROOF ASSEMBLIES ROOF MAIN SUPPORTS...
-
Page 5: Foundation Details
FOUNDATION DETAILS NOTES: POST HOLES 400MM x 400MM ENTRANCE REF: OS111 pg 5 of 17 23.07.2019... - Page 6 FOUNDATION DETAILS REF: OS111 pg 6 of 17 23.07.2019...
- Page 7 INSTALLATION INSTRUCTIONS POSITION FSA ASSEMBLIES POSITION THESE ON THE GROUND 120MM FACE ON THE OUTSIDE INSTALL THE UMT TIMBERS THE 90X90 TIMBER ON THE FSA ASSEMBLIES HELP POSITION THESE REF: OS111 pg 7 of 17 23.07.2019...
-
Page 8: Installation Instructions
INSTALLATION INSTRUCTIONS SCREW THE FAS ASSMBLIES TO THE UMT TIMBERS USING - 97.M8X120CSK - QUANTITY X 32 INSTALL FLOOR ASSEMBLY - FA-a TO SURROUNDS USING - 97.M8X180CSK - QUANTITY X 8 (4 EITHER SIDE) , ENSURE HALF LAP JOINTS FACE UP HALF LAP JOINTS FA - a ENTRANCE... - Page 9 INSTALLATION INSTRUCTIONS ATTACH ADDITIONAL SUPPORTS USING 2 X M8X180MM - SCREWING INTO THE FA ASSEMBLY HALF LAP UAT SUPPORTS HALF LAP INSTALL REMAINING FA-a - SCREW THROUGH HALF LAP JOINT USING - 97.M8X180CSK AND M8X80MM FA - a M8X80MM HALF LAP - X2 SCREWS PER JOINT FA - a ENTRANCE M8X180MM SCREWS X 4 PER SIDE...
- Page 10 INSTALLATION INSTRUCTIONS ATTACH THE RS ROOF TIMBERS USING 2 X 8X80 WOOD SCREW EITHER END, ENSURE TIMBERS ARE POSITIONED AS SHOWN NOTES: ENSURE TIMBERS ARE PRE-DRILLED AND COUNTERSUNK TIMBERS ARE POSITIONED LEVEL WITH THE TOP OF THE UPRIGHT TIMBER ATTACH RM TIMBERS TO KING POST (RT2) AND SCREW TO UPRIGHTS USING 2 X M8X120MM &...
- Page 11 INSTALLATION INSTRUCTIONS REPEAT FOR THE REMAINING RM TIMBERS USING 120MM SCREWS INTO THE KING POST AND 180 SCREWS INTO THE UPRIGHT TIMBERS SCREW RA - ROOF ASSEMBLIES TO RM TIMBERS USING 6 X M8X80MM WOOD SCREWS PER SIDE, ENSURE ROOF IS POSITIONED AS SHOWN REF: OS111 pg 11 of 17 23.07.2019...
- Page 12 INSTALLATION INSTRUCTIONS REPEAT FOR THE REMAINING RA - ROOF ASSEMBLIES SCREW TRIM TIMBERS TO THE MAIN ROOF SUPPORTS (RM TIMBERS) USING 4 X M8X80MM WOOD SCREWS FOR EACH SECTION FIG 1 FIG 2 NOTES: RTA / B TIMBERS ARE TO BE POSITIONED ALTERNATELY TO ENSURE THE TIMBERS DO NOT CLASH - SEE ABOVE FIG 1 ENSURE OVERHANG IS AS SHOWN ABOVE - FIG 2...
- Page 13 INSTALLATION INSTRUCTIONS ATTACH THE RT1 - ROOF CAP USING 4 X M8X80MM WOOD SCREWS ATTACH THE FS TIMBERS AS SHOWN USING 4 X M8X180MM WOOD SCREWS FOR EACH TIMBER NOTES: SCREW THROUGH THE FLOOR ASSEMBLE INTO THE FS TIMBERS AND ANGLED TIMBER SCREW THROUGH THE FS INTO THE OUTER ASSEMBLY FS-B FS-C...
- Page 14 INSTALLATION INSTRUCTIONS START DECKING THE FLOOR USING DECK SCREWS, ENSURE THEY ARE POSITIONED AS SHOWN BELOW NOTES: WORK FROM FRONT TO BACK - SPACING APPROX 2MM BETWEEN TIMBERS ENSURE EACH PIECE IS SCREWED TO ALL SUPPORTS (HIGHLIGHTED RED ) - FIG 3 USE 2 X DECK SCREWS FOR WHERE DECK IS SCREWED INTO FLOOR SUPPORTS - GENERALLY 14 X DECK SCREWS PER SLAT / TIMBER - FIG 4...
- Page 15 INSTALLATION INSTRUCTIONS INSTALL SEAT SUPPORTS ENSURE ENTRANCE HAS AN SSA-(END) EITHER SIDE FIG 5 FIG 6 NOTES: USE 2 X M8X120MM WOOD SCREWS TO SCREW INTO THE UPRIGHT TIMBER - FIG 5 FURTHER SECURE USING 2 X M8X120MM WOOD SCREWS, POSITION THESE SCREWS ON THE ‘INSIDE’...
- Page 16 INSTALLATION INSTRUCTIONS ATTACH SEAT SECTIONS - SS-I &SS-E USING 4X M8X80MM WOOD SCREWS PER SLAT, SEAT SECTIONS ARE IN SETS - a / b NOTES: SCREW INTO THE 43X43 TIMBER SUPPORTS EITHER SIDE OF THE SEAT SUPPORT ‘UPRIGHT’ SS-Ib SS-Ia SS-Ib SS-Ib SS-Ia...
-
Page 17: Installation Complete
INSTALLATION INSTRUCTIONS INSTALLATION COMPLETE PLEASE CHECK ALL SCREWS COUNTERSUNK / NEAT SAND ANY TIMBERS AS REQUIRED REF: OS111 pg 17 of 17 23.07.2019...
Need help?
Do you have a question about the OCTAVIA COMPLETE OS111 and is the answer not in the manual?
Questions and answers