1. Manuals
  2. Brands
  3. Datalogic Manuals
  4. Controller
  5. Controller SC6000
  6. Quick reference manual

Datalogic Controller SC6000 Quick Reference Manual

Scanning controller
Hide thumbs Also See for Controller SC6000:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Reference Manual
SC6000 Controller
QUICK REFERENCE GUIDE

Advertisement

Table of Contents
loading

Related Manuals for Datalogic Controller SC6000

Summary of Contents for Datalogic Controller SC6000

  • Page 1 SC6000 Controller QUICK REFERENCE GUIDE...

  • Page 2: Table Of Contents

    CONTENTS SC6000-1200 STANDARD MODEL ...1 SC6000-1211 PROFIBUS MODEL ...4 SC6000-1215 DEVICENET MODEL ...5 SC6000-1230 DUAL ETHERNET MODEL ...6 COMMON FEATURES ...7 For further details on product installation, see the complete Reference Manual available on the configuration CD-ROM included with this product. NOTE...

  • Page 3: Sc6000-1200 Standard Model

    SC6000-1200 STANDARD MODEL Power ON and Communication LEDs LCD Display Status LEDs Modem Connector Power/Net Connector Main Interface Connector Figure A Connector Panel Figure B Programming Keypad Connector Panel Legend Figure C Ethernet Connector Auxiliary Interface Connector Extended I/O Connector SC6000 STANDARD MODEL...

  • Page 4: Electrical Connections

    Electrical Connections The SC6000 is designed to easily connect to the PWO power supply through two standard accessory cables. All system cabling is concentrated at the PWO except for some Host connections and the Auxiliary interface for SC6000 configuration using a laptop PC. The following connector pinouts are given for reference.
  • Page 5 SC6000 STANDARD MODEL Typical Layouts Ethernet Connection Main Connection Modem Connection...

  • Page 6: Sc6000-1211 Profibus Model

    SC6000-1211 PROFIBUS MODEL Modem Connector Power/Net Connector Main Interface Connector Ethernet Connector Name Function Shield* Shield, protective ground resp. N.C. Not connected B-LINE (RxD/TxD-P) Received/Transmitted data-P CNTR-P** Repeater control signal DGND Data ground (M5V) +5 V Voltage plus (P5V) N.C. Not connected A-LINE (RxD/TxD-N) Received/Transmitted data...

  • Page 7: Sc6000-1215 Devicenet Model

    SC6000-1215 DEVICENET MODEL Modem Connector Power/Net Connector Main Interface Connector Ethernet Connector Name Function Supply voltage – positive pin CAN_L CAN bus data line – L SHIELD Shield CAN_H CAN bus data line – H Supply voltage – negative pin SC6000 DeviceNet Connector Panel DeviceNet Connector Auxiliary Interface Connector...

  • Page 8: Sc6000-1230 Dual Ethernet Model

    SC6000-1230 DUAL ETHERNET MODEL Modem Connector Power/Net Connector Main Interface Connector Ethernet Connector Name Function TX + Transmitted data (+) TX - Transmitted data (-) RX + Received data (+) RX - Received data (-) 4, 5, 7, 8 N.C. Not connected SC6000 DUAL ETHERNET MODEL SC6000 Dual Ethernet Connector Panel...

  • Page 9: Common Features

    COMMON FEATURES Overall Dimensions 39.7 [1.56] [1.57] 319.5 [12.58] [11.73] SC6000 Overall Dimensions [11.80] [12.17] [1.97] [3.35] [3.35] ST-222 Bracket Overall Dimensions COMMON FEATURES 99.7 [3.93] 39.7 [1.56] MØ8 80.2 [3.16] inch [0.63] [0.63] [1.89] N°6 8 [0.32] [3.15] [3.74] inch...

  • Page 10: Mechanical Installation

    Mechanical Installation To mount the SC6000 Controller on the reading station frame proceed as follows: Mount the bracket on the reading station frame: the slots on the bracket will help obtain the best positioning. When working in environments characterized by strong vibrations, set the screws as close as possible to the bracket edges, see the figure below.
  • Page 11 Place a locking washer and then a flat washer onto each knob. Tighten the SC6000 Controller to its bracket by screwing the knobs into their holes - one on each side. Mounting the SC6000 Controller on the bracket The SC6000 Controller can rotate on its mounting bracket up to 90° with respect to the mounting bracket position. See figure below for suggested positions: Suggested Mounting Positions COMMON FEATURES...

  • Page 12: Electrical Installation

    Electrical Installation To make electrical connections to your SC6000 controller proceed as follows: Connect the SC6000 controller to the PWO by means of the appropriate accessory cables for your application. Provide correct and complete system cabling through the PWO according to the signals (Lonworks, encoder P.S., etc.) necessary for the layout of your application.

  • Page 13: Led Indicators

    LED Indicators Power ON and Communication LEDs Name Color Power ON Green Tx Data Green Rx Data Green Ethernet Yellow PS Aux Yellow Tach Yellow Network Name Color Warning Status OK Green Available Models SC6000 - 1XXX Figure 1 - LEDs Description SYSTEM SIGNAL LEDS State Function...
  • Page 14 Keypad and Display The SC6000 keypad allows entering a menu to select one of the functions described in the following paragraphs. STANDARD MODE Upon startup, the diagnostic mask window is visualized by default. Using the UP and DOWN keys it is possible to scroll the other windows following this order: Diagnostic Mask Window Reading Performance Window...
  • Page 15 Alarms This window is available only when enabling the related parameters from the Genius™ configuration program. It shows four alarms generated by the SC6000 or by the network. All alarms are ordered according to their priority (failure messages have priority over warning messages). A failure message causes the Warning LED to be always on, while a warning message causes the LED blinking.
  • Page 16 Compact Flash: by simply installing the old Compact Flash in the new SC6000, the system configuration is automatically restored and the reading station is ready to start working again. Before removing the Compact Flash card, switch the SC6000 Controller off. CAUTION In case of SC6000 failure proceed as follows: Disconnect the device.
  • Page 17 Automatic Scanner Replacement (ASR) When SC6000 is used in a network of DS8100 or DX8200 scanners, (Topology Role parameter = Other; Device Assignment parameter = Controller Lon Old8K), an ASR backup procedure must be performed to automatically manage scanners and SC6000 replacement in case of failure (ASR Restore). In order for the ASR procedure to work, all slave scanners must have been installed according to the procedure in par.
  • Page 18 Technical Features ELECTRICAL FEATURES Supply voltage Power consumption Communication Interfaces Inputs (optocoupled NPN or PNP) Outputs (optocoupled) USER INTERFACE LCD Display Keypad LED indicators SOFTWARE FEATURES Configuration modes Parameter storage ENVIRONMENTAL FEATURES Operating temperature Storage temperature Humidity Vibration resistance Shock resistance Protection class PHYSICAL FEATURES Mechanical dimensions...
  • Page 19 dichiara che dichiara che declares that the declares that the déclare que le déclare que le bescheinigt, daß das Gerät bescheinigt, daß das Gerät declare que el declare que el SC6000-XXXX SC6000-XXXX Universal Controller sono conformi alle Direttive del Consiglio Europeo sottoelencate: are in conformity with the requirements of the European Council Directives listed below: sont conformes aux spécifications des Directives de l'Union Européenne ci-dessous: der nachstehend angeführten Direktiven des Europäischen Rats:...

Table of Contents

Save PDF