Table of Contents
Advertisement
Quick Links
Ball valve
Operating manual
Version
BA-2016.04.26 EN
Print-No.
300 730
TR MA DE Rev001
Series
C16
ASV Stübbe GmbH & Co. KG
Hollwieser Straße 5
32602 Vlotho
Germany
Phone: +49 (0) 5733-799-0
Fax: +49 (0) 5733-799-5000
E-mail: contact@asv-stuebbe.de
Internet: www.asv-stuebbe.com
We reserve the right to make technical changes.
Read carefully before use.
Save for future use.
EN
Advertisement
Table of Contents
Related Manuals for Stübbe C16 Series
Summary of Contents for Stübbe C16 Series
- Page 1 Ball valve Operating manual Series Version BA-2016.04.26 EN ASV Stübbe GmbH & Co. KG Print-No. 300 730 Hollwieser Straße 5 TR MA DE Rev001 32602 Vlotho Germany Phone: +49 (0) 5733-799-0 Fax: +49 (0) 5733-799-5000 E-mail: contact@asv-stuebbe.de Internet: www.asv-stuebbe.com We reserve the right to make technical changes. Read carefully before use.
-
Page 2: About This Document
About this document About this document Other applicable documents This manual • is part of the fitting • applies to all series referred to To download: • describes safe and proper operation during all operating Data sheet C16 phases Technical data, operating conditions Target groups http://www.asv-stuebbe.de/pdf_datasheets/300736.pdf Operating company... -
Page 3: Warnings And Symbols
General safety instructions Warnings and symbols General safety instructions Read and observe the following regulations before carrying Symbol Meaning out any work. • Immediate acute risk 2.2.1 Obligations of the operating company • Death, serious bodily harm • Potentially acute risk Safety-conscious operation •... -
Page 4: Layout And Function
Transport, Storage and Disposal Specific hazards Marking 2.3.1 Hazardous media 3.2.1 Name plate • When handling hazardous media (e.g. hot, flammable, explosive, toxic, hazardous to health or the environment), observe the safety regulations for the handling of haz- 145039 Id No ardous substances. -
Page 5: Installation And Connection
Installation and connection Installation and connection Storage NOTE Preparing for installation Material damage due to inappropriate storage! 5.1.1 Check operating conditions Store the fitting properly. 1. Ensure the design of the fitting is consistent with the pur- 1. Make sure the storage room meets the following condi- pose intended: tions: –... - Page 6 Installation and connection Installing fitting in pipe Drive and limit switch box Limit switch box can only be used with pneumatic drive. WARNING Risk of poisoning and environmental damage from medium. Leak due to faulty installation. Installation work on the pipes should only be performed by technicians who have been specially trained for the pipework in question.
-
Page 7: Performing The Hydrostatic Test
Installation and connection 5.5.2 Pneumatic connection Solenoid pilot valves are available for control of the pneu- matic drive (→ Operating instructions for pilot valve): – 3/2-way valve for single-acting drives – 5/2-way valve for double-acting drives CAUTION Risk of injury from compressed air! All work on the pneumatic system must be carried out by qualified technicians. -
Page 8: Operation
Maintenance Operation Maintenance DANGER Commissioning Risk of electrocution! Fitting correctly installed and connected All electrical work must be carried out by qualified electri- cians only. WARNING WARNING Risk of injury and poisoning due to medium escaping. Risk of injury and poisoning due to hazardous or hot Use personal protective equipment when carrying out any media. -
Page 9: Troubleshooting
Troubleshooting Troubleshooting WARNING Risk of injury and poisoning due to hazardous or hot media. Use personal protective equipment when carrying out any work on the fitting. Safely collect the media and dispose of it in accordance with environmental regulations. Consult with the manufacturer regarding faults which are not identified in the following table, or which cannot be traced to the indicated causes. -
Page 10: Technical Specifications
Appendix Appendix Technical specifications Technical data (→ Data sheet). 9.1.1 Pressure and temperature limits Other media (→ resistance lists). Use at temperatures under 0 °C should be agreed with the manufacturer. PN 16 PN 10 PN 6 T [°C] Fig. 7 Pressure and temperature limits PVC-U Tightening torques Description...
Need help?
Do you have a question about the C16 Series and is the answer not in the manual?
Questions and answers