Casio TE-3000S Dealer's Manual page 246

Appendix (Error code)
Error code (...continued)
Error
Message
code
CHK/TBL No. is Attempt to made use <NEW CHECK> to open a new check
E051
using a number that is already used for an existing check in
occupied
check tracking memory.
CHK/TBL No. is Attempt made to use <OLD CHECK> reopen a new check
E053
using a number that is not used for an existing check in check
not opened
tracking memory.
Out of CHK/TBL Check number range over.
E054
No. range
Normal registration is prohibited during separate check
In the SEP CHK
E055
operation operation.
Attempt to finalize a transaction without specifying <EAT-
Press EAT-IN or
E059
IN> or <TAKEOUT>.
TAKE-OUT key
Printer offline External (local) printer offline
E060
External (local) printer went down.
Printer error
E061
External (local) printer paper end
Printer paper
E062
end
External (local) printing buffer full
Print buffer
E064
full
Print from the Attempt to print the last separated transaction on slip.
E066
beginning of the
transaction
Target print ter The terminal connected with the external (remote) printer is
E070
busy or goes down.
minal busy/down
Target terminal The print buffer of the terminal connected with the external
E071
print BF full (remote) printer becomes full.
The terminal connected with the external (remote) printer
Your receipt/ord
E073
er may not be is goes down,
sued
Attempt to finalize a transaction when balance is less than or
Negative balance
E075
cannot be equal to zero.
finalized
Data exists in the consolidation file.
Data exist in
E085
consolidation
file
Disable to read/reset or consolidate the not found PLU item.
Check NFP items
E099
Operate at the Prohibit master operation.
E100
master terminal
Scanning PLU direct maintenance/batch maintenance file
PLU maintenance
E101
file full. Press becomes full.
<#2> to exit
The PLU code you input is not existed in the PLU file.
PLU Code is not
E103
exist. Input PLU
Code
Scanning PLU/not found PLU file full
PLU file full
E105
Item exists in The designated item has already existed in the scanning PLU
E106
file.
the PLU FILE
The check tracking master terminal is busy or goes down.
Master is busy/d
E110
own. Retry:<CA>
Remove:<ST>
Network startup error.
Inline startup
E121
error
Attempt to register <–> or <CPN> when the balance becomes
Negative balance
E139
negative.
is not allowed
Wrong menu This sheet holder is prohibited by PGM.
E140
Arrangement file is full.
Arrangement file
E146
full
Employee No. is The employee number does not exist in the employee file.
E164
not Found in the
Employee File
Employee No. is The employee number has not been clocked-in yet.
E165
not Clocking-in
The employee number has already been clocked-in.
Employee No. is
E166
Occupied
Time and attendance file becomes full.
Time&Attendance
E176
file full
Insert CF card No CF card is set.
E200
Insufficient memory in the CF card.
Insufficient
E203
memory
File already Can not write, because designated file has already been in the
E205
CF card.
exist.
246
Meaning Action
Finalize and close the check that is currently under the
number that you want to use or use a different check number.
Use the correct check number (if you want to reopen a check
that already exists in check tracking memory) or use <NEW
CHECK> to open a new check.
Enter correct number.
Terminate separate check operation.
Press <EAT-IN> or <TAKEOUT>.
Replace new paper.
Print from the beginning of the transaction
Register item(s) until the balance becomes positive amount.
Clear the data.
Perform it at master terminal.
Terminate the maintenance.
Input the correct PLU code again.
Modify the designated item.
Follow the prompt message.
Enter proper minus/coupon amount.
Set correct sheet holder.
Set the arrangement properly.
Enter the correct employee number.
Enter the correct employee number.
Enter the correct employee number,
Issue the time and attendance reset report.
Set CF card.
Use a vacant (formatted) CF card.
Check the operation and retry.