Advertisement
Originalfassung
DE
BETRIEBSANLEITUNG
Übersetzung / Translation
EN
USER MANUAL
FR
MODE D'EMPLOI
ACHTUNG: Betriebsmittel kontrollieren!
Edition: 09.05.2022 – Revision - 00 – RaR - DE/EN/FR
ZI-HS8TN
EAN: 9120039234236
HOLZSPALTER
LOG SPLITTERS
FENDEUR DE BOIS
ATTENTION: Check Oil!
ATTENTION : Contrôler les
fluides d'exploitation !
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Zipper Mowers ZI-HS8TN
Summary of Contents for Zipper Mowers ZI-HS8TN
- Page 1 BETRIEBSANLEITUNG HOLZSPALTER Übersetzung / Translation USER MANUAL LOG SPLITTERS MODE D'EMPLOI FENDEUR DE BOIS ZI-HS8TN EAN: 9120039234236 ACHTUNG: Betriebsmittel kontrollieren! ATTENTION: Check Oil! ATTENTION : Contrôler les fluides d’exploitation ! Edition: 09.05.2022 – Revision - 00 – RaR - DE/EN/FR...
-
Page 2: Dear Customer
This operating manual contains information and important notes for safe commissioning and handling of the log splitter ZI-HS8TN, hereinafter referred to as "machine". The manual is an integral part of the machine and must not be removed. Keep it for later use... -
Page 3: User Requirements
Check the machine for completeness and function before commissioning. Only use the machine if the guards and other protective devices required for the work are in place, in good working condition and correctly maintained. Select a level, vibration-free, non-slip surface as the installation site. • ZIPPER MASCHINEN GmbH www.Zipper-Maschinen.at ZI-HS8TN... -
Page 4: Residual Risks
Do not reach into the splitting area. • 13.6 Residual risks Despite proper use, certain residual risks remain. Due to the design and construction of the machine, hazardous situations may occur which are indicated as follows in these operating instructions: ZIPPER MASCHINEN GmbH www.Zipper-Maschinen.at ZI-HS8TN... - Page 5 Only move the machine on firm and level ground to prevent it from tilting sideways or tipping completely over. For transport, lower the cylinder, tighten the oil filler plug/air venting device, tilt the machine slightly backwards and move the machine on wheels using the handle. ZIPPER MASCHINEN GmbH www.Zipper-Maschinen.at ZI-HS8TN...
- Page 6 Unfold the log support table and make sure that the three parts are on the same surface level. Insert the hooks of the log support table into the brackets. Tighten the star knob ZIPPER MASCHINEN GmbH www.Zipper-Maschinen.at ZI-HS8TN...
- Page 7 Secure the joint with M6x16 screws, washers and nuts. Secure the log clamps on the arm guards with star knobs and flat washers 5. Assemble plug-ON-OFF switch unit Fix the unit(1) by means of 2 screws and nuts (2). ZIPPER MASCHINEN GmbH www.Zipper-Maschinen.at ZI-HS8TN...
-
Page 8: Operation
(1) Lower both control levers, the splitting wedge lowers to 5 cm above the highest table position. (2) Release one of the two levers, the splitting wedge should be in original position (3) Release both levers, the ram should automatically rise to the highest position. ZIPPER MASCHINEN GmbH www.Zipper-Maschinen.at ZI-HS8TN... - Page 9 Stack as you work. This will provide a safer work area, by keeping it uncluttered, and avoid the danger of tripping, or damaging the power cord. 17 CLEANING, MAINTENANCE, STORAGE, DISPOSAL WARNING Before carrying out any maintenance work, ensure that moving parts are stationary, that the machine is disconnected from the mains supply. ZIPPER MASCHINEN GmbH www.Zipper-Maschinen.at ZI-HS8TN...
-
Page 10: Maintenance
- see picture on the left! NOTICE Hydraulic oils are toxic and must not be released into the environment! Follow the manufacturer's instructions and contact your local authorities for information on proper disposal. ZIPPER MASCHINEN GmbH www.Zipper-Maschinen.at ZI-HS8TN... -
Page 11: Troubleshooting
Repair the bent parts • parts bent Lower hydraulic oil level Check and refill hydraulic oil • • Log Splitter works with abnormal vibration and • Lower hydraulic oil level • Check and refill hydraulic oil noise ZIPPER MASCHINEN GmbH www.Zipper-Maschinen.at ZI-HS8TN...
Need help?
Do you have a question about the ZI-HS8TN and is the answer not in the manual?
Questions and answers