1. Manuals
  2. Brands
  3. Belair Manuals
  4. Indoor Furnishing
  5. BWHA-2LEG2M
  6. Assembly and user's manual

Belair BWHA-2LEG2M Assembly And User's Manual

Electric height adjustable base
Hide thumbs

Advertisement

Table of Contents

Electric Height Adjustable Base
BWHA-2LEG2M
Assembly and User Guide
MAKE SURE NO OBSTACLES ARE IN THE DESK'S
PATH AND ALL CORDS ARE OF APPROPRIATE
!
LENGTH FOR DESK TRAVEL. FAILURE TO COMPLY
WITH OR OBSERVE ALL ASSEMBLY, SAFETY, AND
CAUTION
OPERATION INSTRUCTIONS AND WARNINGS
REGARDING THE USE OF THIS PRODUCT MAY
RESULT IN SERIOUS PROPERTY DAMAGE AND
BODILY INJURY.
IMPORTANT
Any user or installer of this base should study this manual carefully. If this desk is sold, please provide a
copy of this manual to the customer.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BWHA-2LEG2M and is the answer not in the manual?

Questions and answers

Related Manuals for Belair BWHA-2LEG2M

Summary of Contents for Belair BWHA-2LEG2M

  • Page 1 Electric Height Adjustable Base BWHA-2LEG2M Assembly and User Guide MAKE SURE NO OBSTACLES ARE IN THE DESK’S PATH AND ALL CORDS ARE OF APPROPRIATE LENGTH FOR DESK TRAVEL. FAILURE TO COMPLY WITH OR OBSERVE ALL ASSEMBLY, SAFETY, AND CAUTION OPERATION INSTRUCTIONS AND WARNINGS...

  • Page 2: Parts List

    1. PARTS LIST Tape Measure Phillips Head Screwdriver Power Drill Leg x 2 Frame x 2 Crossbar x 2 Side Bracket x 2 Foot x 2 Power Cord Control Box x 1 Handset x 1 14X3/4 Screw x 10 M5X25 Screw x 2 Cord Clip x 5 Allen Key 4mm Plastic Fitting (Spare)
  • Page 3 2. ASSEMBLY INSTRUCTIONS Extend the Frame Crossbar x 2 Frame x 2 Loosen the screws using the Allen key provided. Extend the frame to the desired length. Tighten the screws. Attach Side Brackets Side Bracket x 2 The side bracket snaps into the frame.
  • Page 4 Attach Base to Work Surface 14x3/4 Screw x 10 Attach the base to the work surface with 14x3/4 screws (A). There are no pre-drilled holes so you will need to use a measuring tape to center the base on the work surface. Attach Control Box &...
  • Page 5 Attach Legs to Frame Leg x 2 Insert leg into frame and slot into position. Use the quick-install frame and mechanism to secure the leg. The mechanism will automatically lock the leg in place. Attach Foot Foot x 2 Put the foot on the leg. Use the quick-install mechanism to clamp the foot into position.
  • Page 6 Connect Cords to the Control Box Cord Clip Power Cord 6a Power Cord 6b x 2 Connect one of the Power Cords 6b from the first Leg (1) to the Control Box (7) M1. Connect the other Power Cord 6b from the second Leg (1) to the Control Box (7) M2.
  • Page 7 Flip Desk Upright and Connect Power With the desk at its lowest height turn the assembled desk right-side up with the help of at least one other person. Plug the Power Cord (9) into a 110-240v outlet. NOTE: Grab the desk frame, not the work surface, and turn the desk right-side up. Adjust the Leveling Feet If necessary, adjust the leveling feet to level the desk.

  • Page 8: Up And Down

    3. Operating Manual UP and DOWN Toggle up on the handset to raise the desk. Toggle down on the handset to lower the desk. Menu Navigation Press and hold the right button for 5 seconds to enter the menu. Toggling the handset up or down will scroll through the menu. Pressing the right button will confirm the selection.
  • Page 9 Set the Minimum & Maximum Heights Move the desk to your desired highest/lowest position. Press and hold the right button for 5 seconds to enter the menu. Toggle the handset to highlight the Height Limit submenu and press the right button to confirm your selection. Toggle the handset to highlight either Highest or Lowest and press the right button to confirm your selection.

  • Page 10: Reset Settings

    Changing Units (INCH/CM) Press and hold the right button for 5 seconds to enter the menu. Toggle the handset to highlight the General submenu and press the right button to confirm your selection. Toggle the handset to highlight the Unit submenu and press the right button to confirm your selection.
  • Page 11 4. Error messages on the handset’s display Error Code Description Solution Main voltage over 45v Check the main power supply Height deviation between screws more than Re-initialize 1 cm Handset connection or communication error Check the handset cord Display when blocked Release the button and re-run Main startup unsuccessful, below 20v Replace the main power supply or check the...

  • Page 12: Safety And Warnings

    CAUTION: SAFETY AND WARNINGS • Inappropriate use of this product may cause property or bodily damage. • Check the surroundings on all sides before using the desk. Make sure the desk does not touch the wall. • Please unplug the power supply during lightning and when the product is not in use for a long time. •...

Table of Contents