Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for BIGTREETECH EZ5160 V1.0
Summary of Contents for BIGTREETECH EZ5160 V1.0
- Page 1 BIGTREETECH BIGTREETECH EZ5160 V1.0 User Manual Contents 1 / 13...
-
Page 2: Table Of Contents
BIGTREETECH Revision History ..................... 3 1. Product Introduction ................... 4 1.1 Product Features ..................4 1.2 Product Parameters .................. 4 1.3 Peripheral Interface ................... 5 1.3.1Product Dimensions ................5 1.3.2 Interface Diagram ................6 2. Interface Introduction ..................7 2.1 Installation Method and Interface .............. 7 3. -
Page 3: Revision History
BIGTREETECH Revision History Version Revision Description Date 01.00 First Draft 2022/03/17 3 / 13... -
Page 4: Product Introduction
BIGTREETECH 1. Product Introduction TMC5160 is a high-power stepper motor drive control chip, with an external MOSFET, its maximum voltage can reach 48V, thus the supported stepper motor range is wider, and the adaptability is higher. 1.1 Product Features 1. With the external MOSFET, it can support higher voltage and larger current, and the maximum current can reach 8A (because the module is limited by size and connector, the current cannot exceed 3A);... -
Page 5: Peripheral Interface
BIGTREETECH 1.3 Peripheral Interface 1.3.1 Product Dimensions 5 / 13... -
Page 6: Interface Diagram
BIGTREETECH 1.3.2 Interface Diagram 6 / 13... -
Page 7: Interface Introduction
BIGTREETECH Interface Introduction 2.1 Installation Method and Interface The direction of installing the EZ version driver to the new header is shown in the image below: Function Function (EN) Enable (VM) Motor Supply Voltage (SDI/CFG1) Data (GND) GND (SCK/CFG2) Clock... -
Page 8: Firmware Settings
BIGTREETECH 3. Firmware Settings 3.1 Marlin Firmware Settings Note*: Currently only the firmware of Marlin 2.0 and later supports the SPI mode of TMC5160. Step 1: Find and open the "Configuration.h" file in the Marlin 2.0 firmware, then find "#define MOTHERBOARD XXXXXX", "XXXXX" represents the model of the board used. - Page 9 BIGTREETECH Step 3: Find "#define TMC_SW_MOSI XXX", "#define TMC_SW_MISO XXX", "#define TMC_SW_SCK XXX" under the file in Step 2 and modify "XXX" to the pin you are going to use. Step 4: Find and open "Configuration_adv.h", then find "#define TMC_USE_SW_SPI" and delete "//".
- Page 10 BIGTREETECH Step 5: In the "Configuration_adv.h" file, find "#define X_CURRENT", "#define X_MICROSTEPS", "#define X_RSENSE" and modify the following parameters, (all axes used need to be modified) the RSENSE of the axes used should be modified as "0.075". 10 / 13...
- Page 11 BIGTREETECH After the modification of Step 5, find and open "Configuration.h" and then Step 6: find "#define DEFAULT_AXIS_STEPS_PER_UNIT" and modify the following parameters to set the subdivision, the subdivision of this part must correspond to that of Step 5. 11 / 13...
- Page 12 BIGTREETECH Subdivision Calculation Method: "80, 80, 400, 96" means 16 subdivision, if modified to 32 subdivision, that will be "80*(32/16), 80*(32/16) , 400*(32/16) , 96*(32/16) ". The sampling resistance used in this product is 0.075R, so the effective value of the driving current of this product is 3A.
- Page 13 1.5A), active heat dissipation shall be taken to ensure that the drive can work normally. For more information about this product, please visit https://github.com/bigtreetech/. If you cannot find the information you need, you can contact our after-sales support. Please do not hesitate to contact us if you encounter other problems during use, we will answer your question carefully;...
Need help?
Do you have a question about the EZ5160 V1.0 and is the answer not in the manual?
Questions and answers