Satel abax2 ART-210 Manual
Wireless radiator thermostat
Hide thumbs
Also See for abax2 ART-210:
- Quick start manual (15 pages) ,
- Manual (12 pages) ,
- Instructions manual (9 pages)
Related Manuals for Satel abax2 ART-210
Summary of Contents for Satel abax2 ART-210
- Page 1 Wireless radiator thermostat ART-210 Firmware version 1.00 art-210_pl 07/24 SATEL sp. z o.o. • ul. Budowlanych 66 • 80-298 Gdańsk • POLAND tel. +48 58 320 94 00 www.satel.pl...
- Page 2 13 August 2005). The device meets the technical regulations of the Eurasian Customs Union. SATEL aims to continually improve the quality of its products, which may result in changes in their technical specifications and software. Current information about the changes being introduced is available on our website.
-
Page 3: Table Of Contents
CONTENTS 1 Features ..........................2 2 Description ........................... 2 LED display ........................3 Knob ..........................4 Radio communication ....................5 Energy saving mode (ECO) ..................5 Battery status control ..................... 5 Operating modes ......................5 Thermostat calibration ....................5 Thermostat adaptation ....................5 Boost Heat ........................ -
Page 4: Features
ART-210 SATEL The ART-210 radiator thermostat is used to regulate room temperature which helps to reduce energy consumption. The thermostat allows you to control the radiator valve remotely and manually. It is designed to work within the ABAX 2 two-way wireless system. It is supported •... -
Page 5: Led Display
SATEL ART-210 union nut. LED display. knob. LED display Normally, the display is off. Touch the knob (Fig. 2) to turn on the display. After turning on, the display shows temperature in degrees Celsius from the selected sensor (Fig. 1). Symbols and messages are also shown on the display. -
Page 6: Knob
ART-210 SATEL trouble with changing the valve position. Make sure the thermostat is mounted correctly on the valve and check the valve operation or restart the thermostat (remove the batteries and insert them again). incorrect operating range of the thermostat (calibration failure). Make sure the thermostat is mounted correctly on the valve or restart the thermostat (remove the batteries and insert them again). -
Page 7: Radio Communication
The Manual operating mode can be enabled remotely if the controller is connected to a SATEL alarm control panel. If the operating mode was enabled remotely, the thermostat can only be controlled manually. Remote control is possible only after the mode is disabled remotely. -
Page 8: Boost Heat
ART-210 SATEL Boost Heat If the room temperature is too low and uncomfortable, you can enable the Boost Heat function to heat the room faster. The valve will be fully open for 15 minutes. When this function is enabled, whenever the knob is pressed, the countdown to the end of the function will be displayed alternately with the temperature registered by the sensor. -
Page 9: Tips For Installation
SATEL ART-210 The used batteries must not be discarded, but should be disposed of in accordance with the existing rules for environment protection. 3.1 Tips for installation • The thermostat should be installed indoors, in spaces with normal air humidity. -
Page 10: Mounting On M30X1.5 Mm Valve
ART-210 SATEL 4. Replace the thermostat cover. The marks on the body and cover will help you replace the cover correctly (Fig. 5). 5. Mount the thermostat on the valve (see: Mounting on M30x1.5 mm valve, Mounting on Danfoss RA valve, Mounting on Danfoss RAV valve or Mounting on Danfoss RAVL valve). -
Page 11: Mounting On Danfoss Ra Valve
SATEL ART-210 Mounting on Danfoss RA valve 1. Fasten the adapter on the valve. 1.1. Place the adapter on the valve (Fig. 9). 1.2. Bend open the adapter clamp with a screwdriver and press the adapter against the valve flange (Fig. 10). Make sure the bumps inside the adapter line up with the notches on the valve body. -
Page 12: Mounting On Danfoss Rav Valve
ART-210 SATEL 4. If the thermostat is seated loosely on the valve, use the reducer ring. Unscrew the thermostat, place the reducer ring inside its flange (Fig. 8), then repeat points 2 and 3. Mounting on Danfoss RAV valve 1. Place the cap on the valve pin (Fig. 14). -
Page 13: Mounting On Danfoss Ravl Valve
SATEL ART-210 4. Tighten the thermostat on the adapter (Fig. 19). 5. If the thermostat is seated loosely on the valve, use the reducer ring. Unscrew the thermostat, place the reducer ring inside its flange (Fig. 8), then repeat points 3 and 4. -
Page 14: Manual Control
ART-210 SATEL 5 Manual control If you remove the batteries within 10 seconds since your last activity, the changes will not be saved. 5.1 Changing the operating mode 1. Press the knob to turn on the display. 2. Keep pressing the knob until the temperature / valve position for the operating mode you want to enable is displayed ( - comfort temperature;... -
Page 15: Disabling The Knob (Child Lock)
SATEL ART-210 5.7 Disabling the knob (child lock) You can block the knob when the LED display is turned off or it shows temperature from the sensor ( symbol). Press the knob and hold for 3 seconds. The message will be shown on the display. - Page 16 ART-210 SATEL Radio communication range (in open area) ACU-220 ....................... up to 1000 m ACU-280 ......................up to 500 m Batteries ......................2 x 1.5 V LR6 AA Battery life expectancy ..................up to 2 years Standby current consumption ..................74 µA Temperature measurement range ...............
Need help?
Do you have a question about the abax2 ART-210 and is the answer not in the manual?
Questions and answers