HIKVISION DS-KD8003 Series User Manual
HIKVISION DS-KD8003 Series User Manual

HIKVISION DS-KD8003 Series User Manual

Module door station
Hide thumbs Also See for DS-KD8003 Series:
Table of Contents

Advertisement

Quick Links

DS-KD8003 Series Module Door ‰‰‰‰〷‰n
User Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DS-KD8003 Series and is the answer not in the manual?

Questions and answers

Summary of Contents for HIKVISION DS-KD8003 Series

  • Page 1 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual...
  • Page 2: About This Document

    ● Products described in this Document, which may include licenses obtained from third ‰‰r‰〷‰‰‰ Any part of the Document, including text, pictures, graphics, etc., belongs to Hikvision. No part ● of this Document may be excerpted, copied, translated, or m‰‰‰‰〶‰‰ in whole or in part by any means without wr‰‰〷‰n permission.
  • Page 3 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSS. YOU ACKNOWLEDGE THAT THE NATURE OF THE INTERNET PROVIDES FOR INHERENT SECURITY ● RISKS, AND HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER-ATTACK, HACKER ATTACK, VIRUS INFECTION, OR OTHER INTERNET SECURITY RISKS;...
  • Page 4 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Symbol C‰nv‰n‰〷‰n‰ The symbols that may be found in this document are ‰‰‰〶n‰‰ as follows. Symbol ‰‰‰‰‰‰‰‰〷‰n Indicates a hazardous ‰‰‰‰‰‰〷‰n which, if not avoided, will or could Danger result in death or serious injury.
  • Page 5: Eu Conformity Statement

    DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Regulatory ‰n‰‰‰m‰‰〷‰n EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the EMC ‰‰r‰c‰〷v‰ 2014/30/EU, the RoHS ‰‰r‰c‰〷v‰ 2011/65/EU 2012/19/EU (WEEE ‰‰r‰c‰〷v‰)‰...
  • Page 6 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Conformément à la r‰‰‰‰m‰n‰‰‰〷‰n d'Industrie Canada, le présent ‰m‰‰〷‰‰r radio peut ‰‰nc‰〷‰nn‰r avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour ‰‰‰m‰‰〷‰‰r par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à ‰‰‰n‰‰n‰〷‰n des autres ‰‰〷‰‰‰‰‰‰‰r‰‰...
  • Page 7: Table Of Contents

    DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Contents Chapter 1 Appearance ........................ 1 Chapter 2 C‰n‰〶‰‰‰‰ Sub Module Address ................... 3 Chapter 3 Terminal and Wiring ....................5 3.1 Terminal ‰‰‰cr‰‰‰〷‰n ......................5 3.2 Module Door ‰‰‰‰〷‰n Wiring ....................10 3.2.1 Door Lock Wiring ......................
  • Page 8 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual 6.3 Person Management ......................69 6.4 Device Management ......................70 6.5 Remote C‰n‰〶‰‰r‰‰〷‰n ......................71 6.5.1 Local Parameters ‰‰〷呠n‰‰ ................... 71 6.5.2 View Device ‰n‰‰rm‰‰〷‰n ..................... 73 6.5.3 Set Time ........................73 6.5.4 Set DST ........................74 6.5.5 View Open Source ‰‰‰〶w‰r‰...
  • Page 9: Chapter 1 Appearance

    DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Chapter 1 Appearance Main Unit Figure 1-1 Main Unit Appearance Table 1-1 Appearance ‰‰‰‰‰‰‰‰〷‰n ‰‰‰‰‰‰‰‰〷‰n Microphone Low ‰‰‰‰m‰n‰‰〷‰n IR Supplement Light Built-in Camera Loudspeaker Call B‰‰〷‰n Nametag TAMPER Network Interface ‰‰‰‰‰‰‰′ C ‰nn‰c‰〷n‰ Interface (output)
  • Page 10 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Two-Wire Main Unit Figure 1-2 Two-Wire Main Unit Table 1-2 Appearance ‰‰‰‰‰‰‰‰〷‰n ‰‰‰‰‰‰‰‰〷‰n Microphone Low ‰‰‰‰m‰n‰‰〷‰n IR Supplement Light Built-in Camera Loudspeaker Call B‰‰〷‰n Nametag TAMPER Two-Wire Interface (24 VDC Power Input) ‰‰‰‰‰‰‰′ C ‰nn‰c‰〷n‰ Interface (output)
  • Page 11: Chapter 2 C‰N‰〶‰‰‰‰ Sub Module Address

    DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Chapter 2 C‰n‰〶‰‰‰‰ Sub Module Address You need to set the sub module address via DIP switch before ‰n‰‰‰‰‰‰‰〷‰n‰ Steps 1. Remove the rubber cover on the rear panel of the sub module to expose the DIP switch.
  • Page 12 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual DIP 1 DIP 2 DIP 3 DIP 4 DIP 5 DIP 6 DIP 7 DIP 8 Module Address Module 6 Module 7 Module 8...
  • Page 13: Chapter 3 Terminal And Wiring

    DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Chapter 3 Terminal and Wiring 3.1 Terminal ‰‰‰‰‰‰‰‰〷‰n The power source should be q‰‰‰‰‰〶‰‰ and meet limited power source or PS2 requirements according to IEC 60950-1 or IEC 62368-1 standard. Main Unit Terminals Figure 3-1 Main Unit Terminals Table 3-1 ‰‰‰‰‰‰‰‰〷‰n‰...
  • Page 14 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Interface ‰‰‰‰‰‰‰‰〷‰n AIN1 For the access of Door ‰‰‰n‰‰〷c 1 AIN3 For the access of Exit B‰‰〷‰n 1 AIN4 For the access of Exit B‰‰〷‰n 2 485- ‰‰‰‰‰‰‰′ c ‰nn‰c‰〷n‰ Interface 485+ 12 V OUT2 PoE Network Interface(Supports IEEE 802.3af)
  • Page 15 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Table 3-3 ‰‰‰‰‰‰‰‰〷‰n‰ of Terminals and Interfaces Interface ‰‰‰‰‰‰‰‰〷‰n Door Lock Relay Output (NC) Door Lock Relay Output (NO) Common Interface Door Lock Relay Output (NC) Door Lock Relay Output (NO) Grounding 12 V IN/OUT1 The power output is 12 V, 500mA.
  • Page 16 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Power Supply Distributor Model Distributor Power Door ‰‰‰‰〷‰n Power Output Output 10 W MAX in total DC 12 V DC 12V OUT2 18 W MAX Sub Module Terminal (Except Touch-Display Module) Figure 3-3 Sub Module Terminal (Except Touch-Display Module) Table 3-5 ‰‰‰‰‰‰‰‰〷‰n...
  • Page 17 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Touch-Display Module Figure 3-4 Touch-Display Module Table 3-6 ‰‰‰‰‰‰‰‰〷‰n Interface ‰‰‰‰‰‰‰‰〷‰n 485- ‰‰‰‰‰‰‰′ C ‰nn‰c‰〷n‰ Interface (Input) 485+ 12V IN 485- ‰‰‰‰‰‰‰′ C ‰nn‰c‰〷n‰ Interface (Output) 485+ 12V OUT Grounding Interface CVSB IN...
  • Page 18: Module Door ‰‰‰‰〷‰N Wiring

    DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual 3.2 Module Door ‰‰‰‰〷‰n Wiring 3.2.1 Door Lock Wiring Figure 3-5 Door Lock Wiring...
  • Page 19 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Figure 3-6 Lock Wiring when powered by PoE Note When the device is powered by PoE, the 12V IN/OUT interface can supply power to the lock. ● Terminal NC1/COM is set as default for accessing m‰‰n‰‰〷c lock/electric bolt; terminal NO2/COM ●...
  • Page 20: Door Contact Wiring

    DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual 3.2.2 Door Contact Wiring Figure 3-7 Door Contact Wiring Note AIN1 and AIN2 are defaulted to connect door contact. Door contact connected to AIN1 detects status of the lock that connected to NC1/NO1; Door contact connected to AIN2 detects the status...
  • Page 21: Exit B‰‰〷‰N Wiring

    DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual 3.2.3 Exit B‰‰〷‰n Wiring Figure 3-8 Exit B‰‰〷‰n Wiring Note AIN3 and AIN4 are set as default for c‰nn‰c‰〷n‰ exit b‰‰〷‰n‰ Exit b‰‰〷‰n connected to AIN3 opens the lock connected to NC1/NO1; Exit b‰‰〷‰n connected to AIN4 controls the lock that connected to...
  • Page 22: Chapter 4 ‰N‰‰‰‰‰‰‰〷‰N

    DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Chapter 4 ‰n‰‰‰‰‰‰‰〷‰n Note Sub module must work along with the main unit. ● Sub modules share the same approach of the ‰n‰‰‰‰‰‰‰〷‰n‰ The sub modules in ‰n‰‰‰‰‰‰‰〷‰n images ● are for reference only.
  • Page 23 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Note The dimension of one module m‰‰n‰〷n‰ frame (W × H × D) is: 117 mm × 107 mm × 32.7 mm. ● The dimensions above are for reference only. The actual size can be slightly ‰‰‰〶‰r‰n‰ from the ●...
  • Page 24 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Figure 4-2 Drill Screw Holes 3. Remove the stricker and insert the expansion sleeves into the screw holes. 4. Fix the m‰‰n‰〷n‰ frame onto the wall with 4 expansion bolts.
  • Page 25 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Figure 4-3 Fix the M‰‰n‰〷n‰ Frame 5. Connect the cables to the corresponding interfaces of the main unit and insert the main unit into the frame.
  • Page 26 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Figure 4-4 Insert the Main Unit 6. Fix the cover onto the frame.
  • Page 27 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Figure 4-5 Fix the Cover...
  • Page 28: One-Module Flush ‰‰‰N‰〷N

    DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual 4.1.2 One-Module Flush M‰‰n‰〷n‰ Before You Start Figure 4-6 Front and Side View of the Gang Box...
  • Page 29 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Figure 4-7 Gang Box Note The dimension of one-module gang box is: 115 (W) × 134 (H) × 56 (D) mm. The dimension is for reference only. Steps 1. Drill an ‰n‰‰‰‰‰‰‰〷‰n hole, and pull the cables out.
  • Page 30 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Figure 4-8 Drill ‰n‰‰‰‰‰‰‰〷‰n Hole 2. Remove the ‰‰‰‰‰〷c sheet of the cable entry. 3. Mark the gang box screw holes on the wall. 1) Route the cables through the gang box hole.
  • Page 31 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Note The suggested size of the hole is 6 (diameter) × 45 (depth) mm. 5. Route the cables through the gang box hole. Insert the gang box into the ‰n‰‰‰‰‰‰‰〷‰n hole. Fix the gang box with 4 expansion bolts.
  • Page 32 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Figure 4-11 Remove the M‰‰n‰〷n‰ Ears 7. Connect the cables to the corresponding interfaces of the main unit and insert the unit into the gang box.
  • Page 33 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Figure 4-12 Insert the Main Unit 8. Fix the cover and the main unit with 2 socket head cap screws by using a hexagon wrench (supplied). Figure 4-13 Fix the Cover...
  • Page 34: Two-Module ‰N‰‰‰‰‰‰‰〷‰N

    DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual 4.2 Two-Module ‰n‰‰‰‰‰‰‰〷‰n 4.2.1 Two-Module Surface M‰‰n‰〷n‰ Before You Start Figure 4-14 M‰‰n‰〷n‰ Frame Note The dimension of two-module m‰‰n‰〷n‰ frame (W × H × D) is: 219 mm × 107 mm × 32.7 mm.
  • Page 35 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Steps 1. Paste the ‰n‰‰‰‰‰‰‰〷‰n ‰‰〷c‰‰r 1 onto the wall. Make sure the ‰‰〷c‰‰r is placed horizontally via measuring with the gradienter. 2. Drill 4 holes according to the screw holes on the ‰‰〷c‰‰r‰ The suggested size of hole is 6 (diameter) ×...
  • Page 36 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Figure 4-17 Placement of Lines 6. Connect the cables. 1) Connect the lines and m‰‰‰‰‰‰c‰nn‰c‰〷n‰ line to the corresponding interfaces of the main unit, then place the main unit into the upper grid.
  • Page 37 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Figure 4-18 Line C‰nn‰‰‰〷‰n ‰‰〶‰‰‰ Picture 7. Insert the modules into the frame ‰‰〶‰r wiring. The main unit must be placed in the top grid. Figure 4-19 Insert the Modules 8. Use the hexagon wrench in the package to ‰〶x the cover onto the frame.
  • Page 38 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Figure 4-20 Fix the Cover...
  • Page 39: Two-Module Flush ‰‰‰N‰〷N

    DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual 4.2.2 Two-Module Flush M‰‰n‰〷n‰ Before You Start Figure 4-21 Gang Box Note The dimension of two-module gang box is: 237 (W) × 134 (H) × 56 (D) mm. The dimension is for reference only.
  • Page 40 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Note The suggested dimension of ‰n‰‰‰‰‰‰‰〷‰n hole is 220 (W) × 108 (H) × 45.5 (D) mm. ● The suggested length of cables ‰‰‰〶 outside is 270 mm. ● Figure 4-22 Drill the ‰n‰‰‰‰‰‰‰〷‰n Hole 2.
  • Page 41 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Figure 4-23 Mark the Screw Holes 4. Drill 4 holes according to the marks on the wall, and insert the expansion sleeves into the screw holes. The suggested size of hole is 6 (diameter) × 45 (depth) mm.
  • Page 42 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Figure 4-24 Fix the Gang Box 6. Fill the gap between the gang box and the wall with concrete. Remove the m‰‰n‰〷n‰ ears with tool ‰‰〶‰r concrete is dry.
  • Page 43 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Figure 4-25 Remove the M‰‰n‰〷n‰ Ears 7. Connect cables and insert the modules. 1) Connect Cable 1 and one end of Cable 2 to the corresponding interfaces of the main unit, then insert the main unit into the upper grid.
  • Page 44 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Figure 4-26 Connect Cables and Insert the Modules Note Cable 1 refers to the cables pulled out from the wall that connected to the main unit. Cable 2 refers to the m‰‰‰‰‰‰c‰nn‰c‰〷n‰ line in the accessory package.
  • Page 45: Three-Module ‰N‰‰‰‰‰‰‰〷‰N

    DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual 4.3 Three-Module ‰n‰‰‰‰‰‰‰〷‰n 4.3.1 Three-Module Surface ‰n‰‰‰‰‰‰‰〷‰n Before You Start Figure 4-28 M‰‰n‰〷n‰ Frame Note The dimension of two-module m‰‰n‰〷n‰ frame (W × H × D) is: 320.8 mm × 107 mm × 32.7 mm.
  • Page 46 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Figure 4-29 Drill Screw Holes 3. Remove the ‰‰〷c‰‰r and insert the expansion sleeves into the screw holes. 4. Fix the m‰‰n‰〷n‰ frame onto the wall with 4 expansion bolts. Figure 4-30 Fix the M‰‰n‰〷n‰ Frame...
  • Page 47 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Note The m‰‰n‰〷n‰ frame should be placed exactly as shown below for this step. The tamper plate should be at the low right of the ‰〶r‰‰ grid. Figure 4-31 M‰‰n‰〷n‰ Frame 5. Thread the m‰‰‰‰‰‰c‰nn‰c‰〷n‰ line across the thread holes of the frame. Pass the main unit...
  • Page 48 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Figure 4-32 Placement of Lines 6. Connect the cables. 1) Connect the lines and m‰‰‰‰‰‰c‰nn‰c‰〷n‰ line 1 to the corresponding interfaces of the main unit, then place the main unit into the upper grid.
  • Page 49 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Figure 4-33 Line C‰nn‰‰‰〷‰n ‰‰〶‰‰‰ Picture 7. Insert the modules into the frame ‰‰〶‰r wiring. The main unit must be placed in the top grid.
  • Page 50 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Figure 4-34 Insert the Modules into the Frame 8. Use the hexagon wrench in the package to ‰〶x the cover onto the frame.
  • Page 51 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Figure 4-35 Fix the Cover...
  • Page 52: Three-Module Flush ‰‰‰N‰〷N

    DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual 4.3.2 Three-Module Flush M‰‰n‰〷n‰ Before You Start Figure 4-36 Gang Box...
  • Page 53 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Note The dimension of one-module gang box is: 338.8(W)×134(H)×56(D) mm. ● The dimensions above are for reference only. The actual size can be slightly ‰‰‰〶‰r‰n‰ from the ● ‰‰‰‰r‰‰〷c‰‰ dimension. Steps 1. Cave the ‰n‰‰‰‰‰‰‰〷‰n hole, and pull the cable out.The suggested dimension of ‰n‰‰‰‰‰‰‰〷‰n hole is 321.8(W)×108(H)×45.5(D) mm.
  • Page 54 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Figure 4-38 Mark the Screw Holes 4. Drill 4 holes according to marks on the wall, and insert the expansion sleeves into the screw holes. The suggested size of hole is 6 (diameter) × 45 (depth) mm.
  • Page 55 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Figure 4-40 Remove the M‰‰n‰〷n‰ Ears 7. Connect cables and insert the modules. 1) Connect Cable 1 and one end of Cable 2 to the corresponding interfaces of the main unit, then insert the main unit into the upper grid.
  • Page 56 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Note Cable 1 refers to the cables pulled out from the wall that connected to the main unit. Cable 2 and Cable 3 refer to the m‰‰‰‰‰‰c‰nn‰c‰〷n‰ line in the accessory package. 8. Fix the cover and the main unit with 2 socket head cap screws by using a hexagon wrench (supplied).
  • Page 57: More-Than-Three Module ‰N‰‰‰‰‰‰‰〷‰N

    DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual 4.4 More-Than-Three Module ‰n‰‰‰‰‰‰‰〷‰n 4.4.1 More-than-Three Module Surface M‰‰n‰〷n‰ Before You Start Figure 4-43 M‰‰n‰〷n‰ Frame Note It takes two three-module m‰‰n‰〷n‰ frames. The dimension of three-module m‰‰n‰〷n‰ frame ● (W × H × D) is: 320.8 mm × 107 mm × 32.7 mm.
  • Page 58 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Figure 4-44 Drill Screw Holes 4. Remove the ‰‰〷c‰‰r‰ and insert the expansion sleeves into the screw holes. 5. Thread the m‰‰‰‰‰‰c‰nn‰c‰〷n‰ line (400 mm) and grounding line across the thread hole of both...
  • Page 59 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Figure 4-45 Place the Grounding Line and M‰‰‰‰‰‰C‰nn‰‰‰〷n‰ Line Note There are 6 m‰‰‰‰‰‰c‰nn‰c‰〷n‰ lines in the package: 190 mm × 4 and 400 mm × 2. ● Take the 400 mm m‰‰‰‰‰‰c‰nn‰c‰〷n‰ line for this step.
  • Page 60 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Figure 4-46 Fix the M‰‰n‰〷n‰ Frame 7. Pass the main unit c‰nn‰c‰〷n‰ line across the thread hole to the top grid of the ‰‰‰〶 frame. Thread the m‰‰‰‰‰‰c‰nn‰c‰〷n‰ line (190 mm) across the thread hole of the frame. The lines should be placed as shown below.
  • Page 61 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual 8. Connect the cables. 1) Connect the cables from the wall and m‰‰‰‰‰‰c‰nn‰c‰〷n‰ line 1 to the corresponding interfaces of the main unit, then place the main unit into the upper grid. 2) Connect the other end of the m‰‰‰‰‰‰c‰nn‰c‰〷n‰ line 1 to the input interface of the sub module.
  • Page 62 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Figure 4-48 Line C‰nn‰‰‰〷‰n ‰‰〶‰‰‰ Picture...
  • Page 63 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual 9. Insert the modules into the frame ‰‰〶‰r wiring. The main unit must be placed in the top grid on the ‰‰‰〶‰ Figure 4-49 Insert the Modules 10. Pull the grounding line out and ‰〶x‰‰ its two end to the screw on the cover.
  • Page 64 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Figure 4-50 Connect the Grounding Line to the Cover 11. Use the hexagon wrench in the package to ‰〶x the cover onto the frame.
  • Page 65 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Figure 4-51 Fix the Cover...
  • Page 66: More-Than-Three Module Flush ‰‰‰N‰〷N

    DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual 4.4.2 More-Than-Three Module Flush M‰‰n‰〷n‰ Before You Start Figure 4-52 Gang Box...
  • Page 67 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Note It takes two three-module gang boxes. The dimension of the gang box is: 338.8 (W) × 134 (H) × 56 (D) mm. The dimension is for reference only. Steps 1. Drill the ‰n‰‰‰‰‰‰‰〷‰n hole, and pull the cable out.The suggested dimension of ‰n‰‰‰‰‰‰‰〷‰n hole is 321.8 (W) ×...
  • Page 68 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Figure 4-54 Connect Two Gang Boxes 3. Select a cable entry and remove the ‰‰‰‰‰〷c sheet. 4. Remove the ‰‰‰‰‰〷c sheets on the side of the gang boxes (shown as 1 and 2) below:...
  • Page 69 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual 5. Mark the gang box screw holes on the wall. 1) Route the cables through the gang box hole. 2) Insert the gang box into the ‰n‰‰‰‰‰‰‰〷‰n hole. 3) Mark the gang box screw holes' ‰‰‰‰‰〷‰n with a marker, and take out the gang box.
  • Page 70 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Figure 4-57 Fix the Gang Boxes 8. Fill the gap between the gang box and wall with concrete. Remove the m‰‰n‰〷n‰ ears with tool ‰‰〶‰r concrete is dry. Route the grounding line through the cable entries.
  • Page 71 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Note The green-yellow line in the package is for grounding. 9. Connect cables and insert the modules. 1) Connect Cable 1 and one end of Cable 2 to the corresponding interfaces of the Main Unit, then place the Main Unit into the upper grid of the ‰‰‰〶...
  • Page 72 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Figure 4-60 Cables C‰nn‰‰‰〷‰n Note Cable 2,3,5 and 6 are the m‰‰‰‰‰‰c‰nn‰c‰〷n‰ lines (190 mm) in the package. ● Cable 4 is the m‰‰‰‰‰‰c‰nn‰c‰〷n‰ line (400 mm) in the package. ● Main unit must be put in the top grid.
  • Page 73 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Figure 4-61 Connect the Grounding Line to the Cover 11. Fix the cover with 2 socket head cap screws by using a hexagon wrench (supplied).
  • Page 74 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Figure 4-62 Fix the Cover...
  • Page 75: Chapter 5 ‰‰‰〷V‰‰〷‰N

    DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Chapter 5 ‰‰‰〷v‰‰〷‰n 5.1 ‰‰‰〷v‰‰‰ via Web Browser You can ‰c‰〷v‰‰‰ the device via the web browser. Steps 1. Enter the device default IP address (192.0.0.65) in the address bar of the web browser, and press Enter.
  • Page 76: Chapter 6 C‰N‰〶‰‰‰‰‰〷‰N Via Web Client

    DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Chapter 6 C‰n‰〶‰‰‰‰‰〷‰n via Web Client 6.1 Login Web Browser You can log into the Web browser for device c‰n‰〶‰‰r‰‰〷‰n‰ Before You Start The sub module needs to be connected with the main unit before you can set the sub module via the web client of the main unit.
  • Page 77: Person Management

    DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Set the volume when ‰‰‰r‰〷n‰ live view. Note If you adjust the volume when ‰‰‰r‰〷n‰ two-way audio, you may hear a repeated sounds. You can capture image when ‰‰‰r‰〷n‰ live view. Reserved ‰‰nc‰〷‰n‰ You can zoom in the live view image.
  • Page 78: Add Fingerprint

    DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual ‰‰〶‰r check Administrator in Access Control, the added person can log in the device by ‰‰‰‰‰n‰〷c‰‰〷‰n‰ Click OK to save the ‰‰〷呠n‰‰‰ Set Room No. Click Add to add the Floor No. and Room No..
  • Page 79: Remote C‰N‰〶‰‰R‰‰〷‰N

    DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Synchronize Click Synchronize and enable Synchronize for device ‰ync‰r‰n‰‰‰‰〷‰n‰ Note When enabling the ‰‰nc‰〷‰n‰ the ‰c‰〷v‰‰‰‰ devices will synchronize parameters. ‰n‰c‰〷v‰‰‰‰ devices synchronize parameters whether the ‰‰nc‰〷‰n is enabled or not. Refresh Click Refresh to get the device ‰n‰‰rm‰‰〷‰n‰...
  • Page 80 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Figure 6-3 Local Parameters Live View Parameters Stream Type Set the stream type as Main Stream or Sub-stream. Play Performance Set the live view performance to Shortest Delay, Balanced or Fluent. Auto Start Live View Check Yes to enable the ‰‰nc‰〷‰n‰...
  • Page 81: View Device ‰N‰‰Rm‰‰〷‰N

    DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Click Save to enable the ‰‰〷呠n‰‰‰ Picture and Clip ‰‰〷呠n‰‰ Save snapshots in live view to Set the saving path of the manually captured pictures in live view mode. Note You can click Browse to change the directory for saving the clips and pictures, and click Open to open the set folder of clips and picture saving.
  • Page 82: Set Dst

    DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual 6.5.4 Set DST Steps 1. Click C‰n‰〶‰‰‰‰‰〷‰n → System → System ‰‰〷呠n‰‰ → Time ‰‰〷呠n‰‰ . 2. Enable DST. 3. Set the DST start ‰〷m‰‰ end ‰〷m‰ and bias ‰〷m‰‰ 4. Click Save to save the ‰‰〷呠n‰‰‰...
  • Page 83: Security Service

    DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Click and select the ‰〶‰‰ to import. Click Import to start import c‰n‰〶‰‰r‰‰〷‰n ‰〶‰‰‰ Upgrade Click C‰n‰〶‰‰‰‰‰〷‰n → System → Maintenance → Upgrade & Maintenance . Select an upgrade type from the drop-down list. Click and select the upgrade ‰〶‰‰...
  • Page 84: Account Security ‰‰〷呠N

    DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Proper c‰n‰〶‰‰r‰‰〷‰n of all passwords and other security ‰‰〷呠n‰‰ is the responsibility of the service provider and/or end-user. (If the device supports AP mode, ‰‰〶‰r the admin password is changed, the password of AP ●...
  • Page 85 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Port ‰‰〷呠n‰‰ Steps 1. Click Network → Basic ‰‰〷呠n‰‰ → Port to enter the ‰‰〷呠n‰‰ page. Figure 6-4 Port ‰‰〷呠n‰‰ 2. Set the ports of the device. HTTP Port The default port number is 80, and it can be changed to any port No. which is not occupied.
  • Page 86 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Figure 6-5 SIP ‰‰〷呠n‰‰ 2. Check Enable VOIP Gateway. 3. C‰n‰〶‰‰r‰ the SIP parameters. 4. Click Save to enable the ‰‰〷呠n‰‰‰ FTP ‰‰〷呠n‰‰ Steps 1. Click Network → Advanced → FTP to enter the ‰‰〷呠n‰‰ page.
  • Page 87 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Figure 6-6 FTP ‰‰〷呠n‰‰...
  • Page 88: Video & Audio ‰‰〷呠N

    DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual 2. Check Enable FTP. 3. Select Server Type. 4. Input the Server IP Address and Port. 5. C‰n‰〶‰‰r‰ the FTP ‰‰〷呠n‰‰‰ and the user name and password are required for the server login.
  • Page 89: Audio Parameters

    DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Stream Type Select the stream type to main stream or sub stream. Video Type Select the stream type to video stream, or video & audio composite stream. The audio signal will be recorded only when the Video Type is Video & Audio.
  • Page 90 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Figure 6-8 Audio ‰‰〷呠n‰‰ 2. C‰n‰〶‰‰r‰ the stream type and the audio encoding type. Audio Channel Select the audio channel to adjust the audio parameters. Stream Type Select the stream type to main stream or sub stream.
  • Page 91: Image ‰‰〷呠N

    DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual 6.5.13 Image ‰‰〷呠n‰‰ Display ‰‰〷呠n‰‰ C‰n‰〶‰‰r‰ the image adjustment, backlight ‰‰〷呠n‰‰ and other parameters in display ‰‰〷呠n‰‰‰ Steps 1. Click Image → Display ‰‰〷呠n‰‰ to enter the display ‰‰〷呠n‰‰ page. Figure 6-9 Display ‰‰〷呠n‰‰...
  • Page 92 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Sharpness Sharpness describes the edge contrast of the image, which ranges from 1 to 100. 5. Set the Day/Night Switch. Figure 6-10 Day/Night Switch - Set ‰‰‰‰〷m‰ or Night. - Set the mode as Auto and edit the ‰‰n‰‰‰〷v‰‰y according to your needs.
  • Page 93 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual OSD ‰‰〷呠n‰‰ You can customize the camera name, ‰〷m‰‰‰‰‰‰ format on the live view. Steps 1. Click Image → OSD to enter the ‰‰〷呠n‰‰ page. Figure 6-12 OSD 2. Check to enable Display Name, Display Date or Display Week at your actual needs.
  • Page 94: Event ‰‰〷呠N

    DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Note You can select Cropping ‰‰‰‰‰‰‰〷‰n as 704*576, 1280*720, or 1920*1080. ● You can zoom in or zoom out the image by ‰‰‰‰c‰〷n‰ Cropping ‰‰‰‰‰‰‰〷‰n ‰‰〶‰r clicking Save. ● 6.5.14 Event ‰‰〷呠n‰‰ M‰‰〷‰n ‰‰‰‰‰‰〷‰n ‰‰‰〷‰n ‰‰‰‰c‰〷‰n detects the moving objects in the c‰n‰〶‰‰r‰‰...
  • Page 95 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Figure 6-13 M‰‰〷‰n ‰‰‰‰‰‰〷‰n 2. Click to Enable M‰‰〷‰n ‰‰‰‰‰‰〷‰n. 3. Click Draw Area. Click and drag to draw a m‰‰〷‰n ‰‰‰‰c‰〷‰n area. Clear Area Click Clear All to clear all of the areas.
  • Page 96 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Delete Schedule Click Delete to delete the current arming schedule. 6. Click Linkage Method to enable the linkages. N‰‰〷‰‰ Security Center Send an ‰xc‰‰‰〷‰n or alarm signal to the remote management ‰‰‰〶w‰r‰ when an event occurs.
  • Page 97 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Figure 6-14 Event Linkage...
  • Page 98: Schedule ‰‰〷呠N

    DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual 2. Select the Major Type as Device Event or Door Event. 3. Select the type of the Normal Linkage for the event. 4. Click Save to enable the ‰‰〷呠n‰‰‰ 6.5.15 Schedule ‰‰〷呠n‰‰ You can create call schedule, or else the device will call indoor ‰‰‰‰〷‰n all day by default.
  • Page 99: Set Card Security

    DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Figure 6-16 Holiday Schedule 2) Click Add. 3) Set Start Time and End Time. 4) Select Call Type. 5) Drag mouse to set the schedule according to the actual needs. 6) Click OK.
  • Page 100: Intercom ‰‰〷呠N

    DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual ‰‰〶‰r enable the DESFire card content reading ‰‰nc‰〷‰n‰ the device can read the DESFire card 6.5.17 Intercom ‰‰〷呠n‰‰ Device No. C‰n‰〶‰‰‰‰‰〷‰n Set the No. of the device, and linked devices can build a c‰mm‰n‰c‰‰〷‰n‰...
  • Page 101 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Linked Network ‰‰〷呠n‰‰ Steps 1. Click Intercom → Session ‰‰〷呠n‰‰ to enter the ‰‰〷呠n‰‰ page. Figure 6-18 Session ‰‰〷呠n‰‰ 2. Set ‰‰‰‰‰‰‰‰‰〷‰n Password. 3. Set Main ‰‰‰‰〷‰n IP and Video Intercom Server IP.
  • Page 102 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Set password and remarks and click to enable electric lock. Click Save to save the ‰‰〷呠n‰‰‰ Call ‰‰〷呠n‰‰ Go to Intercom → Call ‰‰〷呠n‰‰ to enter the page. C‰n‰〶‰‰r‰ Max. Call ‰‰‰‰‰〷‰n, Max. Message ‰‰‰‰‰〷‰n and Max. Ring ‰‰‰‰‰〷‰n, and click Save.
  • Page 103 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Set I/O Parameters You can set I/O Parameters on PC Web. Steps 1. Click C‰n‰〶‰‰‰‰‰〷‰n → Video Intercom → I/O ‰‰〷呠n‰‰ . 2. Select Input 2 as Disable or Door Status. Select Input 3 and Input 4 as Disable or Exit B‰‰〷‰n.
  • Page 104: Access Control ‰‰〷呠N

    DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Note The module address is used to ‰‰‰〶‰r‰n‰〷‰‰‰ the sub modules. ● K12 module, KK module and alarm in module belong to nametag modules. ● The room No. for the main unit's call b‰‰〷‰n is 1 by default; and the room No. for other call ●...
  • Page 105: Elevator Control

    DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Figure 6-21 Door Parameters 2. Select Door No., and edit the Name. 3. Set Open ‰‰‰‰‰〷‰n. When the ‰〷m‰ to open over the open ‰‰r‰‰〷‰n you set, the door will be locked again.
  • Page 106 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Figure 6-22 Elevator Control 2. Check to enable elevator control ‰‰nc‰〷‰n‰ 3. Select an Elevator No., and select an elevator controller. 4. Select Interface Type. 5. Enter N‰‰‰‰〷v‰ Floor Capacity, and select Alarm Receiver Type.
  • Page 107 DS-KD8003 Series Module Door ‰‰‰‰〷‰n User Manual Note Up to 4 elevator controllers can be connected to one door ‰‰‰‰〷‰n‰ ● Up to 10 n‰‰‰‰〷v‰ ‰〶‰‰r‰ can be added. ● Make sure the interface types of elevator controllers, which are connected to the same door ●...
  • Page 108 UD29094B-C...

Table of Contents