Related Manuals for Hyundai power products HTHE7128
Summary of Contents for Hyundai power products HTHE7128
- Page 1 ELECTRIC HEDGE TRIMMER HTHE7128 WARNING: Read thoroughly the instruction manual before using.
-
Page 2: Table Of Contents
CONTENTS 1. SAFETY WARNINGS..........................3 2. YOUR PRODUCT........................... 7 3. USE................................8 4. MAINTENANCE AND STORAGE..................... 10 5. DISPOSAL.............................10 6. DECLARATION OF CONFORMITY ....................11 7. WARRANTY............................12 8. PRODUCT FAILURE.......................... 13 9. WARRANTY EXCLUSIONS....................... 14... -
Page 3: Safety Warnings
1. SAFETY WARNINGS WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. -
Page 4: Hedge Trimmer Safety Warnings
power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. c) Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. - Page 5 Observe local or regional safety measures in your area. This also applies to all provisions relating to safety at the workplace and to health prevention in the workplace. The manufacturer cannot be held responsible if the machine has been modified in an unauthorized manner or in such a way as to constitute a final damage.
-
Page 6: Intended Use
Warning! The use of another cutting head or other accessories and extensions, even when specifically recommended, may result in injury or property damage. The machine must not be used for purposes other than those intended. Any divergent use of these purposes must therefore be considered as unauthorized use. -
Page 7: Your Product
5. Rear handle with ON/OFF switch 2. Security protection 6. Supply cord 3. Front handle with ON/OFF switch 7. Cable holder 4. Rotation button 8. Blade protection Technical data Model HTHE7128 Tension 230-240V~, 50Hz Power 710W No load speed 1600min-¹ Blade length 550mm... -
Page 8: Use
3. USE Before cutting Make sure that the tool is properly assembled. Inspect the work area. Remove any materials or objects that may damage the tool or cause accidents. Remember that you must wear full protective equipment and keep spectators away from the work area. -
Page 9: Cutting Techniques
NOTE: Starting the machine can also be done by holding the front handle and starting by pressing the switch on the rear handle. It depends on your work position. Pivoting handle You can change the position of the front handle according the work position you must have. Push the rotation button (1). -
Page 10: Maintenance And Storage
4. MAINTENANCE AND STORAGE Maintain your tool regularly. This will keep your tool in good working order and extend its lifespan. Do not use abrasive, caustic agents to clean the tool. These types of products will damage your tool. Do not perform repairs by yourself. Repairs and inspection must be carried out by a competent person or at an authorized service center (please contact you service dealer). -
Page 11: Declaration Of Conformity
6. DECLARATION OF CONFORMITY BUILDER SAS 32, rue Aristide Bergès - ZI 31270 Cugnaux – France declare that the machine ELECTRIC HEDGE TRIMMER HTHE7128 Serial number: 20230604685-20230605184 Is in conformity with the European Directives: Machine Directive 2006/42/EC EMC Directive 2014/30/EU... -
Page 12: Warranty
7. WARRANTY WARRANTY The manufacturer guarantees the product against defects in material and workmanship for a period of 2 years from the date of the original purchase. The warranty only applies if the product is for household use. The warranty does not cover breakdowns due to normal wear and tear. The manufacturer agrees to replace parts identified as defective by the designated distributor. -
Page 13: Product Failure
8. PRODUCT FAILURE WHAT TO DO IF MY MACHINE BREAKS DOWN? If you bought your product in a store: a) Empty the fuel tank if your product has one. b) Make sure that your machine is complete with all accessories supplied, and clean! If this is not the case, the repairer will refuse the machine. -
Page 14: Warranty Exclusions
9. WARRANTY EXCLUSIONS THE WARRANTY DOES NOT COVER: • Start-up and setting up of the product. • Damage resulting from normal wear and tear of the product. • Damage resulting from improper use of the product. • Damage resulting from assembly or start-up not in accordance with the user manual. •...
Need help?
Do you have a question about the HTHE7128 and is the answer not in the manual?
Questions and answers