Related Manuals for Hyundai power products HDBT314T-1
Summary of Contents for Hyundai power products HDBT314T-1
- Page 1 PETROL BRUSH CUTTER & GRASS TRIMMER HDBT314T-1 WARNING: Read thoroughly the instruction manual before use.
-
Page 2: Table Of Contents
CONTENTS 1. SECURITY WARNINGS 2. YOUR PRODUCT 3. ASSEMBLY 4. FILLING OIL TANK AND FUEL TANK 5. OPERATION 6. MAINTENANCE AND STORAGE 7. CE DECLARATION 8. WARRANTY 9. PRODUCT FAILURE 10. WARRANTY EXCLUSIONS... -
Page 3: Security Warnings
1. SAFETY WARNINGS Proper safety precautions must be observed. Like all power equipment this unit must be handled carefully. DO NOT EXPOSE YOURSELF OR OTHERS TO DANGER. Follow these general rules. Do not permit others to use this machine unless they are thoroughly responsible and have read, and understand the machine manual and are trained in its operation. - Page 4 dealer. The use of any other accessories or attachments may cause a potential hazard or injury to the user, damage to the machine and void this warranty. Clean the machine completely, especially, the fuel tank, its surroundings, and the air cleaner. ...
- Page 5 loss of feeling, consult your physician before further exposing yourself to cold and vibration. Always wear ear protection, loud noise for long time can make hearing debase even lost hearing. Total face and head protection must be wearing to prevent damage from plummet or branch. ...
- Page 6 Kickback and Related Warnings ● Kickback is a sudden reaction to a pinched or snagged rotating wheel, backing pad, brush or any other accessory. Pinching or snagging causes rapid stalling of the rotating accessory which in turn causes the uncontrolled power tool to be forced in the direction opposite of the accessory’s rotation at the point of the binding.
- Page 7 Do not smoke and do use the tool near naked flame The accessible part are hot when operate the tool Caution! Risk of rebound Keep bystanders away at least 15mm Caution! The tool can contact to a voluminous material. Loss of control and injuries can be created.
-
Page 8: Your Product
Skin contact with oil / gasoline Inhalation of gasoline / oil vapors Contact with projected objects Burns when touching with hot surfaces Prolonged use of this product exposes the operator to vibration and can produce so-called "white finger" disease. To reduce the risk, wear gloves and keep your hands warm. If any of the symptoms of "white finger syndrome"... - Page 9 5. Harness 6. Oil cup 7. 3 teethes blade 8. Wrench 9. Metal lock pin/ wrench 10. Nylon cutting head 11. Bar assembly 12. Bracket (handle part support) 13. Handle 14. Handle with throttle trigger, ON/OFF switch and throttle trigger lockout 15.
- Page 10 b. Technical data Engine displacement 31cm³ Maximum engine speed Brush cutter: 9300min-¹ Grass trimmer: 8000min-¹ Maximum power 0,7kW Mass Empty tank: 7,3kg Empty tank with specified attachment: 8kg Full tank and specified attachment: 8,5kg Volume of fuel tank 0,7l Volume of oil tank 0,08l Cutting diameter Grass trimmer: 480mm...
-
Page 11: Assembly
3. ASSEMBLY a) Installation of the tube on the tool Unscrew the bolt (1) and remove the screw cap (2). See Fig 1. Insert the attachment into the connector (Fig 2). Make sure to fix the pin into the hole of the tube. Put back the screw cap (2) and screw the bolt on it (3). - Page 13 c) Installation of the carter of protection Remove the screws which are on the carter of protection (fig7). Install the tube on the carter of protection. Make sure that you have installed it in the correct position (Fig 8). Screw the carter on the tube with the two screws (Fig 9).
- Page 14 d) Installation of the nylon cutting head (for grass trimmer operation) Insert a metal locking tool into the hole on the side of the drive gear and on the tool drive (Fig 10). Remove cover bell and the holding nut from the shaft (Fig 11). Install and screw the nylon cutting head.
- Page 15 e) Installation of metal blade (for brush cutter operation) Insert a metal locking tool into the hole on the side of the drive gear and on the tool drive (Fig 10). Remove cover bell and the holding nut from the shaft (Fig 11). Install, in the following order, on the shaft: the blade, the cover bell and then the holding nut (Fig 13).
-
Page 16: Filling Oil Tank And Fuel Tank
NOTE After installation, always check if the installation is correct. If blade is not well install, it will vibrate excessively and can cause injury. When operation, if there is abnormal vibration, immediately stop the tool and check the installation. 4. FILLING OIL TANK AND FUEL TANK a) Fuel Warning: Gasoline is highly flammable. - Page 17 Filling the tank Unscrew the tank cap. Fill the tank to 80% of its capacity. Screw the fuel cap back on. Clean the fuel tank cap and the area around after filling the fuel tank. Eliminate overfill of fuel mixture by rubbing. b) Oil Open the oil tank.
-
Page 18: Operation
5. OPERATION a) Starting the tool Move the ON/OFF switch to “ON” position (I). Pull the recoil starter until engine starts. For the operation, push and hold the throttle trigger lockout (1) and then push the throttle trigger (2). b) Stopping the tool Release the throttle trigger and the throttle trigger lockout. - Page 19 c) Grass trimmer operation Trimming Tilt the head slowly to direct debris away from you. If cutting up to a barrier such as fence, wall or tree, approach from an angle where any debris ricocheting off the barrier will fly away from you, Move the line head slowly until the grass is cut right up the barrier, but do not jam (overfeed) the line into the barrier.
-
Page 20: Maintenance And Storage
Use the shoulder harness at all times adjust both harness and harness clamp on the unit so that the unit hangs a few inches above ground level .The cutting head and the debris shield should be level in all directions. Harness the unit on the right side of your body. - Page 21 Clean or replace the spark plug in case of ozone contamination. Replace the spark plug if the end of the center electrode is worn. e) Handling and transport The engine should be turned off when the unit is moved between work areas. After the engine has stopped, the muffler is still hot.
-
Page 22: Ce Declaration
Tel : +33 (0)5.34.502.502 Fax : +33 (0)5.34.502.503 declares that the machine: PETROL BRUSH CUTTER & GRASS TRIMMER HDBT314T-1 Serial No: 2021040000321~2021040000580 the people name holding the technical file：Mr. Olivier Patriarca have been designed in compliance with the following standards:... -
Page 23: Warranty
8. WA R R A N T Y WARRANTY The manufacturer guarantees the product against defects in material and workmanship for a period of 2 years from the date of the original purchase. The warranty only applies if the product is for household use. The warranty does not cover breakdowns due to normal wear and tear. -
Page 24: Product Failure
9. P R O D U C T FA I L U R E WHAT TO DO IF MY MACHINE BREAKS DOWN? If you bought your product in a store: a) Empty the fuel tank. b) Make sure that your machine is complete with all accessories supplied, and clean! If this is not the case, the repairer will refuse the machine. -
Page 25: Warranty Exclusions
10. WA R R A N T Y E X C L U S I O N S THE WARRANTY DOES NOT COVER: • Start-up and setting up of the product. • Damage resulting from normal wear and tear of the product. •...
Need help?
Do you have a question about the HDBT314T-1 and is the answer not in the manual?
Questions and answers