Related Manuals for TRENDnet TV-IP100-N
Summary of Contents for TRENDnet TV-IP100-N
- Page 1 Quick Installation Guide TV-IP100-N TV-IP100W-N H/W: 1.0 R...
-
Page 2: Table Of Contents
Table of Contents Table of Contents English ...................... 1 1. Before You Start ................. 2. Hardware Installation ................. 3. Configure the Internet Camera ............Português Para Guia de Instalação em Português, favor ver CD. Eesti Eestikeelse paigaldusjuhendi leiate kaasasolevalt CD-plaadilt. Troubleshooting .................. -
Page 3: English
1. Before You Start Package Contents TV-IP100-N/TV-IP100W-N Utility CD-ROM Quick Installation Guide 1 x 2dBi Detachable Antenna (TV-IP100W-N AC Power Adapter (5V, 2.5A) Camera Mounting Stand System Requirements 10/100Mbps Ethernet Wireless router or wireless access point (TV-IP100W-N) CPU: 1GHz processor or above Memory: 256MB RAM or above/ 512MB RAM or above (Windows Vista) VGA Resolution: 800 x 600 or above Web Brower: Internet Exploreer (6.0 or higher) - Page 4 Application Office Monitoring Front Gate Monitoring (TV-IP100-N) (TV-IP100-N) Wireless N Gigabit Router (TEW-633GR) Internet Parking Monitoring Warehouse Monitoring Cable/DSL Modem (TV-IP100W-N) (TV-IP100W-N) Parking Monitoring Warehouse Monitoring (TV-IP100W-N) (TV-IP100W-N) Wireless N Gigabit Router (TEW-633GR) Internet Office Monitoring Front Gate Monitoring (TV-IP100-N) Cable/DSL Modem (TV-IP100-N) English...
-
Page 5: Hardware Installation
2. Hardware Installation 1. Connect a RJ-45 network cable from a Switch/Router to the Ethernet port of the Internet Camera Server. 2. Attach the Antenna. (TV-IP100W-N) 3. Connect the AC Power Adapter to the Internet Camera Server and then to a power outlet. 4. -
Page 6: Configure The Internet Camera
CD-ROM drive and then click Setup Wizard. 2. Follow the Installation Wizard instructions and then click Finish. 3. Go to Start -> Programs -> TRENDnet -> Setup Wizard and click Setup Wizard. 4. Select the Internet Camera and click Wizard. English... - Page 7 5. Enter the Admin ID and Password, and then click OK. By default: Admin ID: admin Password: admin If you like to change the Admin ID and password, click Change, enter the New ID and the New Password and confirm the New ID and New Password.
- Page 8 8. If WEP is enabled on your wireless network, select the Encryption Mode (e.g. 64-bit, 128-bit), the Key Format (e.g. Hex, ASCII) and the Default Key (e.g. Key_1, Key_2, Key_3, Key_4). Then enter the encryption key in the Key1, Key2, Key3 or Key 4 field.
- Page 9 Active X Control. 15. Click Install. Your installation is now complete. Note: For detailed information regarding the TV-IP100-N/IP100W-N configuration and advanced settings, please refer to the Troubleshooting section, User's Guide on the Utility CD-ROM, or TRENDnet's website at http://www.trendnet.com. English...
-
Page 10: Troubleshooting
This will return settings back to factory defaults. The default IP address is 192.168.10.30. By default, the Admin ID and Password is admin. If you still encounter problems or have any questions regarding the TV-IP100-N/TV-IP100W-N, please contact TRENDnet’s Technical Support Department. - Page 11 Certifications This equipment has been tested and found to comply with FCC and CE Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received. Including interference that may cause undesired operation.
- Page 12 Telephone: +(31) (0) 20 504 05 35 English/Espanol - 24/7 Product Warranty Registration Please take a moment to register your product online. Go to TRENDnet’s website at http://www.trendnet.com/register 20675 Manhattan Place Torrance, CA 90501 Copyright ©2008. All Rights Reserved. TRENDnet.
Need help?
Do you have a question about the TV-IP100-N and is the answer not in the manual?
Questions and answers