Husqvarna Attachment kit J-handle 520iLX Operator's Manual

Hide thumbs Also See for Attachment kit J-handle 520iLX:

Operator's manual (208 pages)

Workshop manual (52 pages)

Operator's manual (24 pages)

Table Of Contents

Quick Links

Download this manual

Attachment kit J-handle 520iLX

Operator's manual

2-11

Table of Contents

Need help?

Do you have a question about the Attachment kit J-handle 520iLX and is the answer not in the manual?

Questions and answers

Summary of Contents for Husqvarna Attachment kit J-handle 520iLX

Page 1 Attachment kit J-handle 520iLX Operator's manual 2-11...
Page 2: Table Of Contents
Contents Introduction..............2 Maintenance..............8 Safety................3 Transportation, storage and disposal......8 Assembly................ 5 Technical data..............8 Operation................ 6 Declaration of Conformity..........10 Introduction Product description Intended use We have a policy of continuous product development WARNING: The J-handle and cutting and therefore reserve the right to modify the design and attachment must only be used together with appearance of the products without prior notice.
Page 3: Safety
5. Single harness • the product is incorrectly repaired. 6. Socket wrench • the product is repaired with parts that are not from the manufacturer or not approved by the 7. Drive disc manufacturer. 8. Grass blade • the product has an accessory that is not from the 9.
Page 4: Safety Instructions For Operation
blade is in motion, otherwise blade thrust may occur. wire, string, etcetera, that could be thrown out or Investigate and take corrective actions to eliminate become wrapped around the cutting attachment. the cause of blade binding. • Make sure that you can move and stand safely. •...
Page 5: Assembly
• Always stop the product, remove the battery and blade shaft or caught between the guard and the make sure that the cutting equipment does not rotate cutting attachment. before you remove material that is wound around the Assembly To assemble the J-handle 3.
Page 6: Operation
7. Tighten the locknut with the socket wrench. Hold the 2. Put the locking pin (C) into the hole on the shaft to shaft of the socket wrench near the blade guard. lock the shaft. Tighten in the opposite direction to how the cutting 3.
Page 7: Blade Thrust
2. Press the stop button. 3. Push the release buttons on the battery and pull the battery out. • Examine the trimmer head and cutting attachment guard for damages or cracks. Replace the trimmer head and cutting attachment guard if they have been hit or if they have cracks.
Page 8: Maintenance
3. The grass is cut down with a sideways, swinging 6. Let the support cup rest lightly against the ground. It movement, where the movement from right-to-left is used to protect the blade from hitting the ground. is the clearing stoke and the movement from left-to- 7.
Page 9 Equivalent sound pressure level at the operator's ear, measured according to EN 62841-4-4 and ISO 22868, dB (A) Vibration levels Vibration levels at handles, measured according to EN 62841-4-4, m/s Equipped with Grassblad 0.7/1.8 255-4, left/right Reported data for vibration level has a typical statistical dispersion (standard deviation) of 2 m/s 2360 - 001 - 03.06.2024...
Page 10: Declaration Of Conformity
Declaration of Conformity EU Declaration of conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Battery-operated Grass Trimmer Husqvarna Brand Attachment kit J-handle 520iLX Type / Model Identification Serial numbers dating from 2024 and onwards...
Page 11 UK Declaration of Conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Battery-operated Grass Trimmer Husqvarna Brand Attachment kit J-handle 520iLX Type / Model Identification Serial numbers dating from 2024 and onwards...
Page 12 Original instructions 1143934-26 2024-06-07...

This manual is also suitable for:

J-handle 520ilx