Page 3
�.If the printer is not going to be used for and extended period of time unplug the power cord. �.Each printer is thoroughly tested before leaving the factory to ensure quality and functionality. It is normal to find evidence of prior use. ��.Visit the official Flsun Wiki for more tutorials on machine use and maintenance: http://wiki.flsun�d.com/en/home.
Component Introduction Filament Dryer Box Parallel Arm Effector Belt Tensioner Hot Bed USB Flash Port Status Indicator Light On/Off Button Orange light indicates abnormal printing, Short press to turn on, long press to turn off. white light prints normally. Dry Box Air Filter Handle Linear Guide...
Packing List ���g PLA-HS Screen Module Service Policy Flsun S� Power Cord Accessory Box Instruction Manual...
Page 8
Accessory Box Packing List Diagonal Plier Silver Needle Hotend Kit Glue Stick Hinges USB Flash Socket Wrench Wrench Set Grease M�*� (�) Screws For fixing hinges M�*��(�)Screws M�*�(�)Screws Open-end Wrench PTFE Tube M�*�(�)Screws For fixing glass door For fixing the screen...
Page 9
Unboxing Remove the tape securing the glass door and Remove the glass door from the packing bag; the wiring harness. Remove glass door;...
Page 10
Unboxing Use M�X� screws to attach the two hinges Fix the glass door using the screws M�*� to the X axis as shown; (with Silicone Plugs) in the accessory box; *Gently tighten the screws Remove the clips from the three belts to unlock the sliders.
Screen Installation Remove the tape securing the wiring harness and plug the display Insert the screen horizontally into the printer slot; power cable and the three data cables into the corresponding connection ports; *The three USB cables are connected by the number. Secure the top of the screen using the M�*�...
Page 12
Connect And Power On Connect the power cord to the right side of the Press the power on/off button to turn on the printer. printer. Press the power switch. The switch will light indicating it is in standby mode. *In case of an emergency while the printer is operating, press and hold the on/off...
Language Settings Please click “ ” ; Please select the language and start using the printer. WiFi Settings Please click “ ” to select the wireless network,you Unable to click "Next" during setup of network connection; want to connect to;...
Page 14
WiFi Settings Enter WiFi password; Click "Join" to connect to the network; If the connection fails, click "Confirm" to attempt to After the printer successfully connects to the network click "Next" to start the printer calibration. reconnect to a new connection.
Page 15
Calibrations Click “Start ” and the printer will complete the During calibration, the "Back" and "Start" buttons are locked calibration in sequence; and cannot be clicked, so please be patient and wait until calibration is complete; Vibration and noise are normal during calibration; You will be prompted on screen when the calibration process is complete.
Loading Filament Install the filament into the filament holder; Push one end of the filament into the feed tube on the right side of the filament dryer box, passing through the filament detector and filam- ent clogging detector, and push the filament down into the effector until the filament cannot move forward;...
Page 17
Loading Filament Wait for the temperature to rise to ���°C; The extruder is loading the filament until the filament is extruded from the nozzle.
First Printing Apply a layer of glue stick to the PEI sheet; Click on "Print" and select the model you want to print; Click "Print" to start printing. *Functions can be manually enabled based on your printing requirements.
Page 19
First Printing filament filament filament The nozzle is too colse Proper distance The nozzle is too far to the hot bed from the hot bed If the nozzle is too low or too high when printing the first layer, you can click " "...
Page 20
Please go to flsun official website to download Flsun Slicer : Official website: https://flsun�d.com Please visit the official Flsun Wiki for more information on machine use, maintenance and FAQs: http://wiki.flsun�d.com/en/home By scanning the QR code you can choose any channel to get the latest product updates and related news.
Page 21
Go all the way forward and break through the limitations!
Page 23
Bring the personalized production capacity to everyone's desktop www.flsun�d.com...
Need help?
Do you have a question about the S1 and is the answer not in the manual?
Questions and answers