Related Manuals for Asus MB14AHD
Summary of Contents for Asus MB14AHD
- Page 1 Monitor Service Manual Model: MB14AHD Version no. V00 Release date: Apr.12, 2024 ...
- Page 2 ASUS will only be responsible for or indemnify you for loss, damages or claims based in contract, tort or infringement under this Warranty Statement. This limit also applies to ASUS’ suppliers and its reseller. It is the maximum for which ASUS, its suppliers, and your reseller are collectively responsible.
- Page 3 Table of Contents 1. Safety Precautions ..............................4 2. Exploded View ..............................5 3. Disassembly & Assembly SOP ..........................7 4. Trouble shooting ..............................18...
-
Page 4: Safety Precautions
1. Safety Precautions Safety information Before setting up the monitor, carefully read all the documentation that came with the package. To prevent fire or shock hazard, never expose the monitor to rain or moisture. Never try to open the monitor cabinet. The dangerous high voltages inside the monitor may result in serious physical injury. -
Page 5: Exploded View
2. Exploded View ... - Page 6 ASUS Description 1+10 PANEL ASS’Y BKT_USB STYLUS PEN REAR COVER HINGE_LEFT HINGE_RIGHT KICK STAND MAIN BOARD KEY BOARD SCREW Q2 2.5 SCREW M2 1.7 SCREW Q2 3.2 SCREW M2 3 ...
-
Page 7: Disassembly & Assembly Sop
3. Disassembly & Assembly SOP 3.1. Precaution Please read the precautions as follows to prevent any damages to the LCD Monitor. Make sure all power connection is removed. Be sure that the LCD Monitor is in power off status. Prepare soft cloth and sponge as working platform to place LCD monitor horizontally. - Page 8 (Note： Please use disassembly tool very carefully to avoid scratching.)
- Page 9 Information in this section is to perform the disassembly procedure of the LCD monitor. Depending on the failures, replace the defective parts accordingly. ASUS MB14AHD LCD monitor consists of various subsystems. This section describes the procedures for LCD monitor disassembly. In addition, the detailed disassembly procedures of individual subsystem will be provided for your service needs.
- Page 10 2. Put a plastic knife into the small gap to open all the latches along the edge of the Rear Cover. Carefully separate the panel module from rear cover. 3. Lay down the rear cover and panel module on a flat, soft and clean surface Tear off the tapes and disconnect the . ...
- Page 11 Main Board and Key board 1. Unscrew the screws to remove the main board, key board and BKT_USB. Disconnect the pin. Description Q’ty Screw Torque Picture &Spec Screw(main 1.2±0.4kgf.cm board/Rear cover) ...
- Page 12 2. Unscrew the screws to remove the HINGE_RIGHT and HINGE_LEFT. Description Q’ty Screw Torque Picture &Spec Screw(HINGE 2.5±0.5kgf.cm /Rear cover) marked in blue Screw(HINGE /Rear cover) 1.2±0.4kgf.cm marked in red ...
- Page 13 ...
- Page 14 3.4 Assembly Procedure Main Board and Key board 1. Prepare the rear cover, kick stand, HINGE_RIGHT and HINGE_LEFT. Use a screwdriver to tighten the screws. Description Q’ty Screw Torque Picture &Spec Screw(HINGE /Rear 2.5±0.5kgf.cm cover) marked in blue Screw(HINGE /Rear cover) marked in red 1.2±0.4kgf.cm...
- Page 15 2. Connect the pin. Assemble the main board, key board and BKT_USB. Description Q’ty Screw Torque Picture &Spec Screw(main 1.2±0.4kgf.cm board/Rear cover) Screw(key board/ 1.2±0.4kgf.cm BKT_USB /Rear cover) ...
- Page 16 Rear cover Subsystem 1. Lay down the rear cover and panel module on a flat, soft and clean surface. Connect the connectors and paste the tapes. Carefully assemble the panel module to rear cover and gently press the side of panel module. ...
- Page 17 ...
-
Page 18: Trouble Shooting
4. Trouble shooting ...
Need help?
Do you have a question about the MB14AHD and is the answer not in the manual?
Questions and answers