Motorola QG-HS830 Quick Start Manual

HS830
Bluetooth®
Wireless Module
Get Connected in
5 Quick Steps
1 - CHARGE
2 - START
BLUETOOTH
FEATURE
3 - PAIR
4 - CONNECT
TO NECK
STRAP
5 - TEST AND
USE
Motorola, Inc.
Consumer Advocacy Office
1307 East Algonquin Road
Schaumburg, IL 60196 USA
Part Number: 6809495A49-O
MOTOROLA and the Stylized M Logo are registered in the US
Patent & Trademark Office. The Bluetooth trademarks are
owned by their proprietor and used by Motorola, Inc. under
license. All other product or service names are the property of
their respective owners.
The use of wireless devices and their accessories may be
prohibited or restricted in certain areas. Always obey the laws
and regulations on the use of these products.
© Motorola, Inc. 2005.
BEFORE YOU
BEGIN
Before using this product, read the Important Safety and Legal
Information pamphlet and follow its instructions.
Take a moment before you get started to
familiarize yourself with your new
HS830 Wireless Module.
Charging Port
Volume
Volume
Up
Down
Button
Button
Indicator Call Button
Light
Module
Jack
3 PAIR
CONTINUED
Your Phone
Step B - SET YOUR PHONE TO LOOK FOR
YOUR MODULE
For most Motorola phones:
Menu >
1 On your Motorola phone, press ( )
M(
Settings > Connection > Bluetooth Link >
Handsfree > Look for Devices.
The phone lists Bluetooth devices it finds.
2
Select Motorola HS830.
3
Select OK or Yes to pair your module with
your phone.
4
Enter the passkey: 0000
5 Select OK.
When your wireless module successfully
pairs with your phone, the indicator light
changes from steadily lit to flashing.
Note: These steps are for most Motorola phones. For other
phones, see your phone's user's guide.
1
CHARGE
Your Module's Battery
Release Tab Down
1
Plug the Motorola charger into the end of
the module with the release tab facing
down.
The indicator light turns on when the battery
is charging. It may take up to 1 minute for
the indicator light to turn on. When the
module's battery is fully charged (about 2
hours), the indicator light turns off.
2
Disconnect the charger.
Note: Module is not functional while charging.
4
CONNECT
Your Module to Neck Strap
1
Insert the 2.5mm plug from the
neck strap into the module jack on the
bottom of the wireless module.
Slots
Plug
Neck
Strap
Holder
Module
Jack
2 Push the wireless module back
into the neck strap holder.
3
Insert the two tabs on the neck
strap holder into the slots on the
top of the wireless module.
4
Place the neck strap around your
neck and insert the earbud in your
ear.
2
START BLUETOOTH
FEATURE
Your Phone
Your phone's Bluetooth feature is off by default.
To use your wireless module, you must turn on
the Bluetooth feature in your phone.
For most Motorola phones:
Menu > Settings > Connection >
1 Press M( ( )
Bluetooth Link > Setup.
2 Scroll to
Power.
3
Select Change.
4 Scroll to On.
5
Press Select to turn on the Bluetooth
feature. The Bluetooth feature remains on
until you turn the feature off.
Note: These steps are for most Motorola phones. For other
phones, see your phone's user's guide.
5

TEST AND USE

Your phone and wireless module are now
paired and ready to make and receive calls.
To make a call:
1 Place the neck strap on and the earbud in
your ear.
2
On your phone, dial the number you want
to call and press the SEND key.
3
If your phone and module are successfully
paired, you will hear ringing on the earbud.
After you have successfully paired your
phone and module, you don't need to
repeat these steps. For daily use, ensure
that your module is turned ON and that
your phone's Bluetooth feature is ON.
To save battery power, turn OFF the
module when you don't use it for an
extended time.
3
PAIR
Your Module
Before you can use your wireless module, you
must pair (link) it with your phone.
Step A - PUT THE MODULE IN PAIRING
MODE
Indicator
Light
1 Ensure the wireless module is turned off
(indicator light not blinking).
2
Press and hold the Call E button for 6
seconds. The indicator light will initially flash,
but continue to hold down the button until
the indicator light is steadily lit.
If the indicator light is flashing or not steadily
lit when releasing the button, repeat both
steps 1 and 2 on this page.

TROUBLESHOOTING

My phone doesn't find my wireless module.
Make sure the indicator light on your wireless
module is on and steady when your phone is
searching for devices (see step 3).
My wireless module worked before but now
it's not working.
Make sure your phone is on and the Bluetooth
feature is turned on in your phone (see step 2).
If the Bluetooth feature was turned off or was
turned on only temporarily, you may need to
restart the Bluetooth feature (see step 2) and
pair your phone and wireless module again (see
step 3).