Page 1
OUTDOOR PIZZA OVEN MODEL# SRPG18003 INSTRUCTION MANUAL Questions, problems, missing / replacement parts? Before returning to your retailer, call our customer service department at 1-888-909-3888, between 7:30 a.m. and 4:30 p.m., PST, Monday through Friday.
Table of contents Before you start..................... Use........................Product maintenance................... Exploded View........................Assembly Instructions....................7-11 Use Instruction....................12-14...
Before you start Important - Food cooking information ALWAYS ALWAYS DO NOT CAUTION - CAUTION - larger cuts of meat Safety warning WARNING – WARNING - WARNING! Only use pellets intended for use in cooking. The recommended pellet length should be no longer than 3cm.
Protection Things to check before you start IMPORTANT - Lighting procedures WARNING! Before each cooking session Replenishing the pellet Extingushing the pizza oven...
Product maintenance The golden rules for care IMPORTANT - At the beginning of the season Before each use After each use Cooking surfaces (pizza stone, etc) Ash tray Pizza oven body After 2 or 3 uses At the end of the season...
Exploded View Parts List PART QUANTITY PART DESCRIPTION QUANTITY DESCRIPTION Ash Tray Pizza Oven Body Assembly Chimney Pipe Poker Hopper Shovel Pizza Stone Hopper Assembly Door Pellet Grid Door Handle Fire Box Assembly Handle Chimney Lid Fire Box Assembly Screw(M4 x10) Estimated Assembly Time: 5 minutes Tools required for assembly (not included): Phillips screwdriver...
Page 7
Assembly Instructions Step 1 With assistance, place the pizza oven body assembly (A) upside down on a soft, level surface. Then unfold four legs (pre-assembled) as illustrated. Step 2 Install the ash tray (H) to the pizza oven body assembly (A) as illustrated.
Assembly Instructions Step 3 Flip over the pizza oven body assembly (A) as illustrated. Step 4 Install the hopper assembly (D) to the pizza oven body assembly (A) with two M4×10 screws (N) as illustrated. Pls disassemble screws (N) from the body (A) when assembling (D).
Page 9
Assembly Instructions Step 5 Put the pizza stone (J) into the pellet pizza oven assembly (A) as illustrated. Step 6 Attach the door handle (L) to the door (K) with 2 pcs M4 x10 screws (N) as illustrated. Tighten screws with screwdriver.
Page 10
Assembly Instructions Step 7 Place the chimney pipe (B) onto the pizza oven body assembly (A) and turn clockwise by hand into position as illustrated. Put the chimney lid (M) onto the chimney pipe (B). Step 8 Place the pellet grid (F) to the fire box assembly (G) first, then put into the pizza oven body assembly (A) as illustrated.
Page 11
Assembly Instructions Step 9 The fire box assembly handle (F) is ready to operate the fire box assembly (G), ash tray (H) and lid of hopper assembly (D). Do not leave the fire box assembly handle (F) on above locations during use as it may get hot.
Use Instruction Lighting 1. Remove the hopper shovel (C, if applicable ) from the top of the chimney pipe (B) and make sure the chimney lid (M) is on top of the chimney pipe (B). 2. Put the door into position and make sure only take it off when adding fuel or operating with food. 3.
Page 13
Use Instruction flames are seen Cooking 1.Baking pizza sticking Reminder: * When the pellet fuel in the pizza oven is burning, the door must be closed unless food needs to be put in or taken out. This is to prevent too much air coming in from the oven door, which may cause heavy smoke inside the fire box assembly(E&G) and hopper assembly(D).
Page 14
Use Instruction 2. Cooking Steak Reminder: *When grilling steak, it is recommended put the steak on the plate(not supplied) to collect grease or gravy. *When the pellet fuel in the pizza oven is burning, the door must be closed unless food needs to be put in or take out.
Page 15
Warranty Information The appliance has been manufactured under the highest standards of quality and workmanship. We warrant to the original consumer purchaser that all aspects of this product will be free of defects in material and workmanship for one year from the date of purchase. A replacement for any defective part will be supplied free of charge for installation by the consumer.
Need help?
Do you have a question about the SRPG18003 and is the answer not in the manual?
Questions and answers