Page 2
Do not attempt to service this product yourself. Refer all servicing to authorized service centers, 2016 and all other applicable UK regulations. The complete declaration of installers, technicians, dealers or distributors. To contact Bose Professional or to find a dealer or conformity can be found at: www.Bose.com/compliance ...
Do not expose loudspeaker or mounting components to any chemical substances that are not specified by Bose Professional, including but not limited to lubricants, cleaning agents, contact sprays, or other hydrocarbon-based solvents. Exposure to such substances can lead to degradation of the plastic material, resulting in cracking and creating a falling hazard.
Page 4
3/8-inch single in 3/8-inch duplex in/loop Wiring the Loudspeaker Wire Gauge The DesignMax DM6C loudspeaker is designed to work with 18 AWG (0.8 mm ) to 14 AWG (2.1 mm ) size wire only. Connection Diagrams Expose six millimeters (1/4 inch) of bare wire to attach to the terminals.
Page 5
Pull the rails outward to secure them together. Bose Professional recommends using (1) a safety wire or Align the rails parallel to each other and press the tile (2) a safety cable as a secondary securing mechanism.
Page 6
Tighten the anchor arm screws to secure the loudspeaker. If using a power drill, set to a low torque setting. WARNING: Over-tightening the screws may result in damage to the anchor attachment point or the ceiling, which could lead to a falling hazard. 6 • English DesignMax DM6C • Installation Guide...
Page 7
NFPA 70, National Electrical Code, 2017, Article 300-22(c) NFPA 90-A, 2015, Installation of Air Conditioning and Ventilation Systems, Paragraph 4.3.11.2.6.5 The DesignMax DM6C loudspeaker has been designed to the requirements defined in the following European regulatory specification for combination systems: Tested to IEC60268-5, 2007 Installation Guide •...
Para comunicarse con Este producto cumple con todos los requisitos correspondientes de la Directiva de Bose Professional o para encontrar un distribuidor cerca de usted, visite la UE. La declaración de conformidad completa se puede encontrar en: BoseProfessional.com.
Page 9
17.74 kg (39.1 lb) No exponga el altavoz ni los componentes de montaje a sustancias químicas que no hayan sido especificadas por Bose Professional, incluidos, entre otros, lubricantes, productos de limpieza, aerosoles de contacto u otros disolventes a base de hidrocarburos. La exposición a estas sustancias puede degradar el plástico, lo...
Page 10
3/8 pulgadas Cableado de los altavoces Calibre de cable El altavoz DesignMax DM6C está diseñado para funcionar únicamente con cables que midan de 18 AWG (0.8 mm a 14 AWG (2.1 mm Diagramas de conexión Exponga 6 milímetros (1/4") de cable sin aislación para...
Page 11
Ubique el puente de mosaico montado en la cuadrícula del techo. Si es necesario, ajuste el puente de mosaico de modo que los rieles descansen sobre la cuadrícula del techo. Reemplace el mosaico del techo. Guía de instalación de • DesignMax DM6C Español • 11...
Page 12
ADVERTENCIA: Apretar demasiado los tornillos puede dañar el punto de conexión del anclaje o el techo, lo que puede producir el riesgo de que se caiga el dispositivo. 12 • Español Guía de instalación de • DesignMax DM6C...
Page 13
Estándar NFPA 70, Código Eléctrico Nacional, 2017, Artículo 300-22(c) Estándar NFPA 90-A, 2015, instalación de sistemas de aire acondicionado y ventilación, Párrafo 4.3.11.2.6.5 El altavoz DesignMax DM6C se diseñó según los requisitos definidos en la siguiente especificación reglamentaria europea para sistemas combinados: Probado según IEC60268-5, 2007...
Page 14
à des centres de service, installateurs, techniciens, revendeurs ou distributeurs agréés. Pour appliquent. La déclaration de conformité complète est disponible à l’adresse contacter Bose Professional ou pour trouver un revendeur ou un distributeur près de chez vous, suivante : www.Bose.com/compliance.
Page 15
Caractéristiques techniques Informations importantes concernant l’installation Vous trouverez des caractéristiques supplémentaires dans la fiche technique des enceintes DesignMax DM6C sur Ce produit est destiné à un usage en intérieur uniquement. BoseProfessional.com. L’installateur est responsable du respect de tous les codes et règlements locaux et nationaux en vigueur applicables à...
Page 16
3/8 pouces boucle 3/8 pouces Câblage de l’enceinte Épaisseur des câbles L’enceinte DesignMax DM6C est conçue pour fonctionner avec des câbles de taille 18 (0,8 mm ) à 14 AWG (2,1 mm uniquement. Diagrammes de connexion Exposez six millimètres (1/4 po) de fil dénudé...
Page 17
Alignez les bras et insérez les languettes dans les fentes. avec le code de l’urbanisme local. Tirez les bras vers l’extérieur pour les fixer les uns Bose Professional recommande l’utilisation de : (1) un fil aux autres. de sécurité ou (2) un câble de sécurité comme dispositif de sécurité...
Page 18
Serrez les vis des bras de fixation pour fixer l’enceinte. Si vous utilisez une visseuse électrique, réglez-la sur un couple faible. AVERTISSEMENT : un serrage excessif des vis peut endommager les points de fixation ou le plafond, ce qui pourrait créer un risque de chute. 18 • Français DesignMax DM6C • Guide d’installation...
Page 19
Conformité aux réglementations et aux normes de sécurité en vigueur L’enceinte DesignMax DM6C a été soumise avec succès à une phase complète de tests et elle est conforme aux spécifications et utilisations suivantes : Conformes à la norme ANSI/UL 1480A-2016, Enceintes destinées à un usage professionnel (sécurité) et commercial Utilisation générale, catégorie UL UEAY, dossier S 5591, numéro de contrôle 3N89...
Versuchen Sie nicht, dieses Produkt selbst zu warten. Lassen Sie jegliche Reparatur- und Dieses Produkt entspricht allen Anforderungen der geltenden EU-Richtlinien. Die Wartungsarbeiten nur von autorisierten Servicepartnern, Monteuren, Technikern, Händlern oder Distributoren durchführen. Die Bose Professional Kontaktdaten für Ihr Land finden Sie auf vollständige Konformitätserklärung ist einsehbar unter: BoseProfessional.com.
Page 21
Bauvorschriften zu achten. Stellen Sie sicher, dass der Lautsprecher und die Montagekomponenten nicht mit chemischen Substanzen in Berührung kommen, die nicht von Bose Professional zugelassen sind. Dies umfasst unter anderem Schmiermittel, Reinigungsmittel, Kontaktspray oder andere Lösungsmittel auf Kohlenwasserstoffbasis. Der Kontakt mit solchen Mitteln kann zu Rissen im Kunststoffmaterial und infolgedessen zum Herunterfallen führen.
Page 22
3/8 Zoll Duplex-Anschluss/ Einzelanschluss Schleife Verkabeln des Lautsprechers Kabeldurchmesser Der DesignMax DM6C Lautsprecher wurde für den ausschließlichen Gebrauch mit Kabeln der Größen 18 AWG (0,8 mm bis 14 AWG (2,1 mm ) entwickelt. Anschlussdiagramme Isolieren Sie einen Teil des Drahtes (6 mm) für den Anschluss an die Anschlüsse ab.
Page 23
Bauvorschriften entsprechen. Richten Sie die Schienen aus und passen Sie die Laschen in die Aussparungen ein. Bose Professional empfiehlt die Verwendung (1) eines Sicherungsdrahtes oder (2) eines Sicherungsseils Ziehen Sie die Schienen nach außen, um sie zu befestigen. zur zusätzlichen Absicherung der Konstruktion.
Page 24
Ziehen Sie die Halterungsschrauben fest, um den Lautsprecher zu fixieren. Wenn Sie einen Akkuschrauber verwenden, stellen Sie eine niedrige Drehmomentstufe ein. WICHTIGER HINWEIS: Ein Überdrehen der Schrauben kann die Stabilität des Verankerungspunkts oder der Decke beeinträchtigen und möglicherweise zum Herunterfallen führen. 24 • Deutsch DesignMax DM6C • Installationsanleitung...
Page 25
Händen auf dem Lautsprecher. Das Abdeckgitter haftet magnetisch am Lautsprecher. Sicherheitshinweise und gesetzliche Bestimmungen Der DesignMax DM6C Lautsprecher hat die Testreihen bestanden und entspricht den folgenden Normen und Einsatzanforderungen: Zertifiziert gemäß ANSI/UL 1480A-2016, Speakers for Commercial & Professional Use Allgemeine Gebrauchsfähigkeit –...
Page 26
Per Informazioni sulle normative contattare Bose Professional o per trovare il rivenditore o distributore più vicino, visita Questo prodotto è conforme a tutti i requisiti pertinenti delle direttive UE.
Evitare di esporre il diffusore o i suoi componenti di montaggio a sostanze chimiche non specificate da Bose Professional, incluse senza limitazione quelle lubrificanti e detergenti, gli spray per contatti e altri solventi a base di idrocarburi.
Page 28
9,5 mm da 9,5 mm Cablaggio del diffusore Diametro dei cablaggi Il diffusore DesignMax DM6C è concepito esclusivamente per l’impiego con cavi di dimensioni comprese tra 18 AWG (0,8 mm ) e 14 AWG (2,1 mm Schemi di collegamento Scoprire 6 mm di filo non rivestito da collegare ai terminali.
Page 29
Tirare le barre in direzione opposta per fissarle l’una all’altra. Bose Professional raccomanda l’utilizzo di (1) un cavo di frenatura o di (2) un cavo di sicurezza come meccanismo Allineare le barre in modo che siano parallele l’una di fissaggio secondario.
Page 30
Serrare le viti della staffa di ancoraggio per fissare il diffusore. Se si utilizza un avvitatore elettrico, impostare un basso valore di coppia. AVVERTENZA: un serraggio eccessivo delle viti può danneggiare il punto di aggancio dell’elemento di ancoraggio o il soffitto, con conseguenti rischi di caduta. 30 • Italiano DesignMax DM6C • Guida all’installazione...
Page 31
La griglia si aggancia magneticamente al diffusore. Conformità alle norme di sicurezza Il diffusore DesignMax DM6C ha superato i test ai quali è stato sottoposto, risultando conforme alle specifiche e alle applicazioni indicate di seguito: Conforme alle specifiche ANSI/UL 1480A-2016, Diffusori per uso professionale e commerciale e di sicurezza...
Dit product voldoet aan alle vereisten van de van toepassing zijnde geautoriseerd servicecenter, installateur, technicus, dealer of distributeur. Om contact op te EU-richtlijnen. De volledige conformiteitsverklaring kunt u vinden op: nemen met Bose Professional en voor informatie over de dichtstbijzijnde dealer of distributeur, www.Bose.com/compliance. gaat u naar BoseProfessional.com.
Page 33
Dit product is alleen bestemd voor binnengebruik. Raadpleeg voor aanvullende specificaties het datasheet Het is de verantwoordelijkheid van de installateur om ervoor met technische gegevens voor de DesignMax DM6C op te zorgen dat de installatie van de luidsprekers en het BoseProfessional.com.
Page 34
9,5 mm enkel in 9,5 mm duplex in/lus De luidspreker bekabelen Bekabelingsdiameter De DesignMax DM6C loudspeaker is uitsluitend ontworpen voor bedrading van 18 AWG (0,8 mm ) tot 14 AWG (2,1 mm Aansluitdiagrammen Strip zes millimeter van de kabelisolatie voor bevestiging van de kale kabel aan de aansluitingen.
Page 35
Lijn de rails uit en steek de lipjes door de openingen. geldende bouwvoorschriften en -verordeningen. Trek de rails naar buiten om de onderdelen te bevestigen. Bose Professional raadt aan (1) een veiligheidsdraad Zorg dat de rails evenwijdig aan elkaar liggen en druk de of (2) veiligheidskabel te gebruiken als secundaire ring van de tegelbrug naar beneden om de ring aan de bevestigingsmethode.
Page 36
Draai de ankerarmschroeven vast om de luidspreker te bevestigen. Stel bij gebruik van een elektrische boor-/ schroefmachine het apparaat in op een laag koppel. WAARSCHUWING: Wanneer u de schroeven te vast draait, kan het ankerbevestigingspunt of het plafond beschadigen, wat kan leiden tot een risico op vallen. 36 • Nederlands DesignMax DM6C • Installatiehandleiding...
Page 37
NFPA 70, National Electrical Code, 2017, artikel 300-22(c) NFPA 90-A, 2015, Installation of Air Conditioning and Ventilation Systems, Paragraph 4.3.11.2.6.5 De DesignMax DM6C loudspeaker is ontworpen volgens de vereisten die zijn vastgelegd in onderstaande specificatie van Europese regelgeving voor combinatiesystemen: Getest volgens IEC60268-5, 2007 Installatiehandleiding •...
Page 39
Sørg for at braketten er montert i henhold til lokale byggeforskrifter. Ikke eksponer høyttaleren eller monteringskomponentene for kjemikalier som ikke er spesifisert av Bose Professional, inkludert, men ikke begrenset til, smøremidler, rengjøringsmidler, kontaktsprayer eller andre hydrokarbonbaserte oppløsningsmidler. Slike midler kan forårsake at plastmaterialet brytes ned, som igjen kan forårsake sprekker...
Page 40
3/8-tommers dobbel inngang inngang / sløyfe Kable høyttaleren Kabeldiameter DesignMax DM6C-høyttaleren er utformet for å fungere kun med kabler på mellom 18 AWG (0,8 mm ) til 14 AWG (2,1 mm Koblingsdiagrammer Eksponer seks millimeter av ledningen for å feste til terminalene.
Page 41
Sett skinnene over hverandre og sett inn tappene bestemmelser. i sporene. Bose Professional anbefaler at du bruker (1) en Dra skinnene utover for å feste dem sammen. sikkerhetsledning, (2) en sikkerhetskabel som sekundær Sett skinnene parallelt med hverandre og trykk ned sikringsmekanisme.
Page 42
Stram skruene på ankerarmen for å feste høyttaleren. Hvis du bruker en elektrisk drill, må du stille den inn på lavt dreiemoment. ADVARSEL: Hvis skruene strammes for mye, kan dette forårsake skade på ankerfestepunktet eller taket, og at høyttaleren faller ned. 42 • Norsk DesignMax DM6C • Monteringsveiledning...
Page 43
NFPA 70, National Electrical Code, 2017, artikkel 300-22(c) NFPA 90-A, 2015, montering av klimaanlegg og ventilasjonssystemer, paragraf 4.3.11.2.6.5 DesignMax DM6C-høyttaleren er utformet i henhold til kravene som er definert i følgende europeiske forskrifter for kombinasjonssystemer: Testet i samsvar med IEC60268-5, 2007 Monteringsveiledning •...
Page 45
Waga przesyłki (para) 17,74 kg (39,1 funta) działanie substancji chemicznych, które nie zostały dozwolone przez firmę Bose Professional, w tym m.in. środków smarnych i czyszczących, środków do ochrony instalacji elektrycznych oraz innych rozpuszczalników na bazie węglowodorów. Narażenie na działanie takich substancji może prowadzić do degradacji materiałów plastikowych, a w rezultacie do pękania i stworzenia...
Page 46
3/8 cala, pojedynczy 3/8 cala, podwójne wejście/pętla Okablowanie głośnika Grubość przewodu Do montażu głośnika DesignMax DM6C należy stosować wyłącznie przewody o rozmiarze od 18 AWG (0,8 mm do 14 AWG (2,1 mm Schematy połączeń Odsłonić sześć milimetrów (1/4 cala) nieizolowanego przewodu, aby podłączyć...
Page 47
Pociągnąć szyny na zewnątrz, aby je zamocować. Firma Bose Professional zaleca użycie (1) przewodu Ustawić szyny równolegle do siebie i wcisnąć zabezpieczającego lub (2) kabla zabezpieczającego pierścień mostka płytkowego, aby zamocować...
Page 48
Dokręcić śruby ramienia kotwiącego, aby zamocować głośnik. W przypadku używania wiertarki udarowej należy ustawić niski moment obrotowy. OSTRZEŻENIE: zbyt mocne dokręcenie śrub może spowodować uszkodzenie punktu mocowania zaczepu lub sufitu, co może prowadzić do zagrożenia upadkiem. 48 • Polski DesignMax DM6C • Podręcznik instalacji...
Page 49
Informacje dotyczące bezpieczeństwa i zgodności Głośnik DesignMax DM6C przeszedł testy i jest zgodny z następującymi specyfikacjami i zastosowaniami: Zgodność z normami ANSI/UL 1480A-2016, Głośniki do bezpiecznego użytku komercyjnego i specjalistycznego Do zastosowań ogólnych – kategoria UL UEAY, numer pliku S 5591, numer kontrolny 3N89 UL-2043, 2013, Test pożarowy i widzialne uwalnianie dymu dla produktów dyskretnych i ich akcesoriów...
Page 61
60 頁「安裝揚聲器」。 安裝網罩 將安全短繩針插入揚聲器的孔洞。請使用雙手將網罩對準揚聲器。網罩會以磁力吸附在揚聲器上。 安全與規章遵循 DesignMax DM6C loudspeaker 揚聲器通過測試,且符合下列規格及用途: 名列 ANSI/UL 1480A-2016 適合商業及安全專業用途的揚聲器 一般用途 - UL Category UEAY,案號 S 5591,控制號 3N89 UL-2043,2013 年,《Fire Test and Visible Smoke Release for Discrete Products and their Accessories Installed in Air Handling Spaces》(裝於空氣調節空間之分離性產品及其配件的防火測試及可視煙霧釋放)。適合用於空氣調節 (氣室) 空間。...
Page 67
一般用途向けの使用 - UL Category UEAY、File Number S 5591 Control Number 3N89 UL-2043、2013年、Fire Test and Visible Smoke Release for Discrete Products and their Accessories Installed in Air Handling Spaces空調(プレナム)空間内での使用に対応 NFPA 70、米国電気工事規程(2017年、第640条)に準拠したクラス1、クラス2、クラス3の配線による設置に対応 NFPA 70、米国電気工事規程、2017年、第300-22(c)条 NFPA 90-A、2015年、Installation of Air Conditioning and Ventilation Systems、第4.3.11.2.6.5節 DesignMax DM6Cは、コンビネーションシステム向けの以下の欧州規制仕様で規定されている要件に適合するように作られています。 IEC60268-5準拠試験を実施、2007年 設置ガイド • DesignMax DM6C 日本語 • 67...
Need help?
Do you have a question about the DesignMax DM6C and is the answer not in the manual?
Questions and answers