English Contents Dear Customer, Guide to Using this Manual Safety Precautions and Working Thank you for choosing a quality engineered STIHL product. Techniques Assembling the Unit It has been built using modern Adjusting the Throttle Cable production techniques and comprehensive quality assurance.
English Engineering improvements Guide to Using this Manual Safety Precautions and Working Techniques STIHL's philosophy is to continually improve all of its products. For this Special safety precau- Pictograms reason we may modify the design, tions must be observed engineering and appearance of our...
Page 4
(e.g. with a hair net, with your doctor before operating a tool by STIHL or are technically cap, hard hat, etc.). power tool. identical. If you have any questions in this respect, consult a servicing dealer.
Page 5
Check that the spark plug boot is After fueling, tighten – secure – a loose boot may cause STIHL offers a comprehensive range of down the screw-type fuel arcing that could ignite combustible personal protective clothing and cap as securely as fumes and cause a fire.
Page 6
Note that combustible fuel immediately by moving the slide control vapor may escape from the fuel system. / stop switch to 0 or STOP. BT 130...
Page 7
– Avoid contact with electri- servicing dealer. The period of usage is shortened by: cal cables or wires – risk STIHL recommends the use of genuine of electric shock. Any personal tendency to suffer – STIHL replacement parts. They are...
Use only high-quality two-stroke engine STIHL MotoMix uses STIHL HP Ultra control handle onto the end of the oil – preferably STIHL HP, HP Super or two-stroke engine oil for an extra long groove HP Ultra, which are specially formulated engine life.
30 days. Exposure to light, the sun, low or high temperatures can quickly make the fuel mix unusable. STIHL MotoMix may be stored for up to 2 years without any problems. Before fueling, clean the filler cap...
(max. 3 seconds) – the auger must not rotate. If the auger brake fails, it must be repaired immediately by a servicing dealer – STIHL recommends the STIHL dealer. BT 130...
(3) align that order. This is the starting throttle position. Insert the retaining pin into the hole Fold down the spring clip of the retaining pin so that it encloses the auger shaft BT 130...
Page 12
– it might otherwise break. speed immediately – or the clutch might otherwise be damaged. Do not let the starter grip snap back. Guide it slowly back into the housing so that the starter rope can rewind properly. Continue cranking. BT 130...
Move the slide control to START. Set the choke knob to e – even if When the engine starts, blip the the engine is cold. throttle trigger to disengage the Now start the engine. starting throttle position – the slide BT 130...
Once the jammed auger is again. For longer out-of-service periods released, check that the auger – see "Storing the Machine". brake functions properly – see "Auger brake" BT 130...
Replace after every 100 operating hours Have checked by servicing dealer Spark arrestor in muffler Have cleaned or replaced by servicing dealer All accessible screws and nuts (not adjust- Retighten ing screws) Check Anti-vibration elements Have replaced by servicing dealer Gearbox Re-lubricate BT 130...
Page 16
The following intervals apply to normal operating conditions only. If your daily work- ing time is longer or operating conditions are difficult (very dusty work area, etc.), shorten the specified intervals accordingly. Drilling spindle Clean Check Auger Replace Safety labels Replace STIHL recommends an authorized STIHL servicing dealer. BT 130...
Right handle: 2.2 m/s Lubrication: STIHL gear The K-factor in accordance with lubricant for STIHL single cylinder four-stroke engine Directive 2006/42/EC is 2.5 dB(A) for brushcutters with mixture lubrication the sound pressure level and sound power level; the K-factor in accordance...
Need help?
Do you have a question about the BT 130 and is the answer not in the manual?
Questions and answers