Table of Contents
Advertisement
Quick Links
Originalfassung
DE
BETRIESANLEITUNG
Übersetzung / Translation
EN
USER MANUAL
ES
INSTRUCCIONES DE SERVICIO
FR
MODE D'EMPLOI
CZ
NÁVOD K POUŽITÍ
SK
NÁVOD NA POUŽITIE
SL
NAVODILA ZA UPORABO
HR
KORISNIČKI PRIRUČNIK
ACHTUNG: Öl kontrollieren!
Motor startet nicht bei Ölmindermenge!!
Edition: 23.03.2022 – Revision 00 – TrT – DE/EN/ES/FR/CZ/SK/SL/HR
ZI-STE2000IV
EAN: 9120039239132
STROMERZEUGER
GENERATOR
GENERADOR
GROUPE ÉLECTROGÈNE
GENERÁTOR ELEKTRICKÉHO PROUDU
GENERÁTOR PRÚDU
ELEKTRIČNI GENERATOR
ELEKTRIČNI GENERATOR
ATTENTION: Check Oil!
Engine don't start with low oil!!
Advertisement
Table of Contents
Related Manuals for ZIPPER MASCHINEN ZI-STE2000IV
Summary of Contents for ZIPPER MASCHINEN ZI-STE2000IV
- Page 1 NÁVOD NA POUŽITIE GENERÁTOR PRÚDU NAVODILA ZA UPORABO ELEKTRIČNI GENERATOR KORISNIČKI PRIRUČNIK ELEKTRIČNI GENERATOR ZI-STE2000IV EAN: 9120039239132 ACHTUNG: Öl kontrollieren! ATTENTION: Check Oil! Motor startet nicht bei Ölmindermenge!! Engine don’t start with low oil!! Edition: 23.03.2022 – Revision 00 – TrT – DE/EN/ES/FR/CZ/SK/SL/HR...
-
Page 2: Dear Customer
Check the goods immediately after receipt and note any complaints on the consignment note when taking over the goods from the deliverer! Transport damage must be reported to us separately to us within 24 hours. ZIPPER MASCHINEN GmbH cannot accept any liability for transport damage that has not been reported. Copyright © 2022 This documentation is protected by copyright. -
Page 3: Intended Use Of The Machine
A higher starting current of inductive loads must be considered. N O TE ZIPPER MASCHINEN assumes no responsibility or warranty for any other use or use beyond this and for any resulting damage to property or injury. -
Page 4: User Requirements
1.5 Ω. As a guideline, the total length of the cables should not exceed 60 m for a cross-section of 1.5 mm2 and 100 m for a cross-section of 2.5 mm2. ZIPPER MASCHINEN GmbH www.zipper-maschinen.at ZI-STE2000IV... -
Page 5: Hazard Warnings
Exhaust fumes contain toxic carbon monoxide. The exposure can cause unconsciousness and • death. No other person, children or pets shall remain within 5m! • 11.7 Hazard warnings 11.7.1 Residual risks Despite intended use, certain residual risk factors remain. ZIPPER MASCHINEN GmbH www.zipper-maschinen.at ZI-STE2000IV... - Page 6 Always switch off the engine when transporting and refuelling the machine! • Ensure that the ON-OFF switch is turned to position “OFF”. After operation, allow the machine to cool down for at least 15 minutes. • ZIPPER MASCHINEN GmbH www.zipper-maschinen.at ZI-STE2000IV...
-
Page 7: Pre-Operation Check
Observe the safety regulations for fuel control. Filter the fuel during refuelling to prevent foreign particles from entering the combustion chamber. Wipe up leaked fuel. WAR N I N G Never refuel if the engine is running ZIPPER MASCHINEN GmbH www.zipper-maschinen.at ZI-STE2000IV... - Page 8 When you recognize that a connected device acts unusual you must stop the machine and disconnect the device. Control whether the device is damaged or if the machine was overloaded by the device. The max. performance of the connected devices must be within the specifications for the • machine. ZIPPER MASCHINEN GmbH www.zipper-maschinen.at ZI-STE2000IV...
- Page 9 Shut down the connected devices and disconnect them from the machine. • Let the machine run for some time without connected devices to cool down. Switch off the machine by putting the ON-OFF switch to position „OFF“. • ZIPPER MASCHINEN GmbH www.zipper-maschinen.at ZI-STE2000IV...
- Page 10 If this happens, wait a few minutes. In order to resume operation, press the DC-circuit breaker 12V (1). 13.9 USB-Port The USB-port on the control panel can be used for charging electrical devices (5Vdc, max. 2A) which are compatible with the USB standard. ZIPPER MASCHINEN GmbH www.zipper-maschinen.at ZI-STE2000IV...
-
Page 11: Maintenance
Control the level Engine oil Change Control Air filter Change X (1) Control Spark plug Change Fuel tank and Clean X (2) fuel filter Fuel pipe Control X (2) ZIPPER MASCHINEN GmbH www.zipper-maschinen.at ZI-STE2000IV... - Page 12 • Loosen the screw (3) and remove the cover (4). • Take out the air filter. • Clean the air filter with soapy water, then rinse with clear water and let it dry thoroughly before reassembling. • The reassembly is done in reverse order. ZIPPER MASCHINEN GmbH www.zipper-maschinen.at ZI-STE2000IV...
- Page 13 N O TE Improper storage can damage and destroy important components. Only store packed or already unpacked parts under the intended ambient conditions! ZIPPER MASCHINEN GmbH www.zipper-maschinen.at ZI-STE2000IV...
-
Page 14: Troubleshooting
Fill engine oil • • Overload indicator light • High temperature protection Cool down the engine • glows activated • Overload protection activated • Reduce existing load • Short circuit protection activated • Check loads ZIPPER MASCHINEN GmbH www.zipper-maschinen.at ZI-STE2000IV...
Need help?
Do you have a question about the ZI-STE2000IV and is the answer not in the manual?
Questions and answers