Advertisement
Advertisement
Table of Contents
Related Manuals for Asus PA32UCXR
Summary of Contents for Asus PA32UCXR
- Page 1 Monitor Service Manual Model: PA32UCXR Version no. v1 Release date: 2023/12/18...
- Page 2 Warranty Statement, up to the listed contract price of each product. ASUS will only be responsible for or indemnify you for loss, damages or claims based in contract, tort or infringement under this Warranty Statement.
- Page 3 Table of Contents Safety Precautions---------------------------------------------------------------------04 Exploded View--------------------------------------------------------------------------05 Disassembly and Assembly Procedures--------------------------------------------06 Troubleshooting------------------------------------------------------------------------13...
-
Page 4: Safety Precautions
1. Safety Precau ons Product Announcement: This product is certificated to meet RoHS Directive and Lead-Free produced definition. Using approved critical components only is recommended when the situation to replace defective parts. Vender assumes no liability express or implied, arising out of any unauthorized modification of design or replacing non-RoHS parts. -
Page 5: Exploded View
2. Exploded View... -
Page 6: Disassembly And Assembly Procedures
3. Disassembly and Assembly Procedures 3.1 Disassembly SOP Tear off 1pcs tape, then disconnect the key wire, Use a Philips-head screwdriver to remove four sensor wire, lamp cables, color wire and connect wires screws for unlocking mechanisms. (No.1~4 screw size=M4x11; Torque=9~11kgfxcm) away to the connectors of the board. - Page 7 Put the middle frame on a protect cushion. Tear off the adhesive tape on the key board, then use a Philips-head screwdriver to remove 5pcs(4+1) screws for unlocking the key board and sensor board. (No.1~5 Screw size=M2x2.2, Torque=1±0.2kgfxcm) Disconnect the speakers wires and lamp cable from the connectors of the board, then release wires from the hooks of the bracket chassis, and then release the two speakers from the probers of the main chassis.
- Page 8 Use a Philips-head screwdriver to remove 10pcs screws for unlocking power board, interface board and MCU board. (No.1 screw size=M4x8, Torque=6 kgfxcm; ±1 No.2~10 screw size=M3x6, Torque=6 kgfxcm) ±1 Remove the power board, MCU board and interface board from the bracket chassis carefully, and then disconnect all of the cables.
- Page 9 3.2 Assembly SOP Turn over the interface board and put it into the bracket, then settle all the cable(put 1pcs cushion Place a main bracket chassis base on a protective to protect). Take 1pcs MCU board, then paste 1pcs cushion, then paste 6pcs silicon sheet on the mylar on the MCU board, then connect the MCU correct positions as the picture below shown.
- Page 10 Take 1pcs LVDS(1) to connect with the right connector of the panel, then locate the cable into the hook of the right hinge and fix it with 1pcs acetate tape. Take 1pcs long lamp cable(2) and 1pcs LVDS cable(3) to connect with the panel connectors(left), then locate the cables into hooks of hinge and mylar.
- Page 11 Take a pair of speakers, then locate the two speakers Locate the assembled color bracket into the hooks and wires into the hooks of the bracket chassis as the of the middle frame, then use a Philips-head picture below shown, then connect the speakers wires screwdriver to tighten 3pcs screws for locking the and LVDS cable to the connectors of the board.
- Page 12 Paste 4pcs aluminum foil on the specific positions to fix the cables and bracket as the picture below shown. Assmble1pcs the rear cover with the assembled unit, then use a Philips-head screwdriver to tighten 4pcs screws for unlocking the rear cover with the unit, then paste 1pcs label on the correct position of the rear cover as the picture below shown.
-
Page 13: Troubleshooting
5. Trouble Shoo ng...
Need help?
Do you have a question about the PA32UCXR and is the answer not in the manual?
Questions and answers